Blaupunkt IR-S1L Handleiding

Blaupunkt Bewakingscamera IR-S1L

Lees hieronder de 📖 handleiding in het Nederlandse voor Blaupunkt IR-S1L (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Wireless - P- Pet Immune PIR Motion Sensor (IR S1L)

1. Learn/Test Button LED indicator&

Press the button to transmit a learn/test code and enter Test

mode for 3 minutes. The LED will light up whenever a movement

is detected under Test mode.

2. Battery Insulator

3. Supervision Enable/Disable Jumper Switch

(JP2)

4. High/Low S umper Switch (JPensitivity J 3)

5. Tamper Switch

The Tamper switch protects the unauthorized cover PIR from

opening.

1 x PIR Sensor

4 x wall plugs and screws

1 y - x 3V lithium batter (pre installed)

Supervision Enable/Disable Jumper Switch (JP2)

If enabled, the PIR sensor will transmit supervision signal to

Control Panel periodically for the sensor to monitor PIR sensor

condition.

Jumper set to ON = supervision function is Disabled

Jumper set to OFF = supervision function is Enabled (Default)

High/Low Sensitivity Jumper Switch (JP3)

Jumper set to ON = PIR sensitivity is set to High (Default)

Jumper set to OFF= PIR sensitivity is set to Low

Put the Control Panel into learning mode, then press the learn

button to transmit learn code. Please refer to Control Panel

manual for to complete the learning process.

The PIR Sensor has knockouts on the back where plastic is

thinner. The 2 center knockouts are for flat wall mounting, and the

4 side knockouts are for corner mounting Mount the PIR Sensor .

at 1.9m to 2m height for optimal performance.

1. Break through the knockouts; use the knockouts to mark

position on the wall or corner.

2. Drill holes into the wall or corner using the knockouts as

template.

3. Fix the PIR Sensor base onto the wall with the screws and

plugs provided.

4. Replace the PIR Sensor cover onto the base.

The PIR ” of approxifeatures a “sleep time mately 1 minute for

power conservation . After transmitting a detected movement, the

PIR will not retransmit for 1 minute. Any further movement

detected during this sleep period will extend the sleep time by

another minute. In this way continuous movement in front of a

PIR will not unduly exhaust the battery.

Press the Test Button to enter Test mode for 3 minutes. Sleep

timer will be disabled under Test mode, and the LED indicator will

flash every time a movement is detected. Use the Test mode to

determine PIR detection coverage and plan the installation

location accordingly.

LLEEDD IInnddiiccaattoorr

Off

Normal Operation

On (2 seconds)

- When Tamper Switch is triggered

- Movement detection under low battery,

tamper triggered, or Test mode.

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is removed

parked on one pin.

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is removed

parked on one pin.

Surface Fixing

Knockouts x 2

(Inside)

Corner Fixing

Knockouts x 4

The PIR -has pet immune function and will not trigger false alarm

from household pet under approximately 27 kg within 7 meters.

Please note this is a rough estimate number and the actual pet

immune performance may vary according to your home

environment and pet size. For example, a dog standing on its

hind leg or a cat climbing on furniture may trigger alarm more s

easily than when they are standing on floor. Please test the pet

immune function with your pets to find out the ideal installation

location before mounting the PIR.

The PIR uses one 3V lithium battery as its power source.

Remove the battery insulator to activate battery. It also features

low battery detection function to notify the Control Panel when

battery voltage is low.

When PIR is on low battery, follow the procedure below to

change the batteries.

1. Open the PIR back cover.

2. Remove the old batteries.

3. Press the tamper switch several times to fully discharge.

4. Insert the new batteries observing correct polarity. The PIR

LED will light up for 30 seconds to indicate it is warming up.

5. Replace the PIR back cover.

EEnnvviirroonnmmeennttaall CCoonnddiittiioonn

- - 10°C to 40°C, relative humidity 85% non condensing.

868 MHz

Product specificaties

Merk:	Blaupunkt
Categorie:	Bewakingscamera
Model:	IR-S1L
Kleur van het product:	Wit
Connectiviteitstechnologie:	Draadloos
Aantal:	1
Afmetingen (B x D x H):	87.7 x 66.4 x 47.7 mm
Kijkhoek:	110 °
Bedrijfstemperatuur (T-T):	-10 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 85 procent
Sensor afstand:	200 m