Blaupunkt BX-S1 Handleiding

Blaupunkt Bewakingscamera BX-S1

Lees hieronder de 📖 handleiding in het Nederlandse voor Blaupunkt BX-S1 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Wireless Outdoor Bell Box (BX-S1)

1. Mounting Holes x 4

2. Tamper Switch

The tamper switch protects the device from being opened or from

being removed from mounting surface.

3. Function Switch Block

Contains 7 DIP Switches to enable the learning mode and to set

the alarm period of siren and strobe light.

4. Power Switch

To enable/disable the power supply

5. Securing Screw

6. LEDs

1 x Outdoor Bell Box

4 x large wall plugs and screws

4 x 1.5V D alkaline batteries

1. Open the front cover and locate the Function Switch Block.

2. Use a sharp object to set Dip SW3 & SW4 on the function

switch block to your desired alarm length.

3. Enter learning mode for your control panel.

4. Slide the Power Switch to ON position to power on the Bellbox.

5. Slide Dip SW1 to the ON position. The Bell Box LED 1 & 3 will

flash once with a short beep. The BX-S1 is now in learning

mode. After 3 seconds, the Bell Box will send out a learning

code, the LED 1 & 3 will flash once to confirm

6. If the Control Panel receives the learning signal, please refer to

the Control Panel manual to complete the learning process.

When learning is complete, the Control Panel will send signal

to the Bell Box to confirm. The Bell Box will sound a short beep

and LED 1 & 3 will flash once to indicate learning is successful.

7. If the Control Panel fails receive a learning code, slide Dip SW1

back to OFF, and then ON position again to enter learning

mode again.

8. If the Bell Box does not respond, please remove the Bell Box

from the control panel and repeat steps 3-6 again.

9. Slide Dip SW1 to the OFF position to leave learning mode. If

you do not slide Dip SW1 back to OFF position, the Bell Box

will automatically leave the learning mode in one hour.

The Outdoor Bell Box has 4 mounting holes on the back cover for

wall mounting.

Before Installation, refer to your Control Panel manual to

temporarily disable the Siren Tamper function to avoid

accidental alarm trigger.

SW1 Siren Learnin

OFF Normal o

eration

ON Learn-in mode

SW2 Strobe Activation

OFF onl

durin

siren alarm

eriod

ON until alarm is disarmed

SW3 SW4 Siren Duration

OFF OFF 3 min.

ON OFF 5 min.

OFF ON 10 min.

ON ON 1 second

(

test

)

SW5 Reserved

SW6 Memor

Reset

OFF Normal

ON Clear Memor

SW7 Su

ervision

OFF Su

ervision function disable

ON Su

ervision function enable

 For further detail please see

aanndd

Mounting Holes

x 4

1. Use the 4 mounting holes on the back to mark position on the

wall.

2. Drill holes into the wall using the mounting holes as template.

3. Fix the base onto the wall with the screw and plugs provided.

4. Replace the front cover onto the base.

5. Enable the Siren Tamper function on you Control Panel.

When mounting the Bell Box, please take note of the following

points:

 Mount on the external wall at a prominent location.

 Mount as high as possible out of easy reach.

The Bell Box is protected by a tamper switch which will be

activated if the Bell Box is removed from the mounted location, or

its cover opened. When installing the Bell Box, please make sure

the tamper switch is properly compressed against the wall, and

the front cover is secured with screw.

Before installing the Bell Box, changing mounting location or

batteries, please make sure to disable the tamper switch

temporarily using your Control Panel’s Siren Tamper function and

enable the tamper switch again after finish working on the Bell

Box. Please refer to your Control Panel manual for detail.

The siren produces a minimum of 104 dBA sound pressure at 1

meter range when activated.

For Burglar and Panic Alarm, the Bell Box gives a continuous

alarm sound.

For Fire / Water alarm, the Bell Box gives an intermittent alarm

sound of 2-sec siren followed by a 1 sec interval.

The siren is silenced when either the programmed siren length

expires or when the Control Panel is disarmed to turn off the siren.

Please refer to Dip Switch table above to set your desired alarm

length through Dip Switch SW3 and SW4 setting.

SSttrroobbee ((LLEEDD)) LLiigghhtt

When the Bell Box is activated, the LED strobe light will also flash

to indicate the Bell Box is alarming. The duration of strobe light

flash is determined by Dip Switch SW2 setting. When set to OFF,

the strobe light will flash according to the alarm length set by Dip

Switch SW3 and SW4. When set to ON, the strobe light will flash

after the alarm length has expired until the control panel is

disarmed.

Audio & Visual Status Indication Table

The Bell Box will activate its siren and strobe light to notify the

user of system status, please refer to below table.

* Siren Audio indication will be effected by the Confirmation ON /

OFF setting in your Control Panel settings.

The Bell Box uses four 1.5V D alkaline batteries as its power

source. It also features low battery detection function to notify the

Control Panel when battery voltage is low.

When the Bell box is on low battery, follow the procedure below

to change the batteries.

1. Temporarily disable the Bell Box’s tamper protection function

(please refer to your Control Panel manual for detail). The Bell

Box will sound a beep to indicate the tamper is disabled.

2. Remove the front cover.

3. Remove the four screws fixing the battery compartment and

take off the compartment lid.

4. Remove the old batteries and press the Tamper Switch twice to

discharge.

5. Insert the new D cell alkaline batteries into the battery

compartment according to correct polarity.

6. The Bell Box will emit beeps and flash when the last battery is

inserted.

7. Replace the battery compartment lid and front cover

8. Enable the tamper protection function through your Control

Panel. The Bell Box will sound a beep to indicate.

EEnnvviirroonnmmeennttaall CCoonnddiittiioonn

-10°C to 40°C, relative humidity 85% non-condensing.

433 MHz

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

FFCCCC CCaauuttiioonn::

To assure continued compliance, any changes or modifications

not expressly approved by the party responsible for compliance

may void the user's authority to operate this equipment. (Example

- use only shielded interface cables when connecting to computer

or peripheral devices).

Arm/Home 1 beep* 3 LED flashes at

once

Disarm 2 beeps* Sequentially

flashes for 1 cycle

Arm (Low Battery) 5 beeps 3 LED flashes for

three times

Disarm (Low

Battery) 5 beeps Sequentially

flashes for 2 cycles

Arm (Tamper) 5 beeps 3 LED flashes for

three times

Disarm (Tamper) 2 beeps* Sequentially

flashes for 2 cycles

Previous alarm

warning 3 sec beep Sequentially

flashes for 2 cycles

Tamper Alarm Continuous beeps Sequentially

flashes

Entry/Exit Sound Count-down beeps None

Product specificaties

Merk:	Blaupunkt
Categorie:	Bewakingscamera
Model:	BX-S1
Kleur van het product:	Wit
Connectiviteitstechnologie:	Draadloos
Aantal:	1
Afmetingen (B x D x H):	287 x 220 x 63 mm
Bedrijfstemperatuur (T-T):	-10 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 85 procent
Sensor afstand:	200 m