Black And Decker WM525 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Black And Decker WM525 (20 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20
Workmate®525
Copyright © 2004 Black & Decker Printed in China
Cat. No. WM525 Form No. B&D 588974-03, Rev. 1 (Sept. ‘04)
588974-03,01,WM525* 9/24/04 2:07 PM Page 1
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PRODUCT,
CALL .1-800-54-HOW-TO (544-6986)
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE, CATALOG NO., TYPE NO., AND DATE CODE.
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE
YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR
COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
(544-6986)
I
MPORTANT SAFETY INSTRUCTIONS
WARNING:
1. Do not load with more than 450 lbs (204 kg) in Workmate Mode or 200 lbs (91 kg)
in Hand Cart Mode.
2. Do not apply an unbalanced load which could cause the Workmate to tip over.
3. Do not step on or stand on Workmate. Do not use the Workmate as a stepladder or
standing platform.
4. Do not store Workmate outdoors or in a damp location.
5. Avoid applying excessive force when clamping with the Swivel Grips.
6. Be sure that the legs are fully open and that the Transition Lever and Toe Plate Slider
locks in position. Secure Hand Cart loads to steel frame members as necessary
7. When using a power tool with the Workmate, follow the safety instructions in the
tool’s instruction manual.
8. Always wear safety glasses when operating power or hand tools.
9. An even pressure of the Vise Jaws on the workpiece is essential. Tighten both
Vise Hand Cranks uniformly.
10. Cutting or drilling into work surface may result in striking metal jaw support below,
damaging tool or work centre.
11. Caution required when using high temperature tools (heat guns, torch, solder
iron, etc.). May damage work surface and reduce clamping capability.
WARNING: This product contains chemicals, including lead, known to the
State of California to cause cancer, and birth defects or other reproductive harm.
Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
NOTE! The assembly of the Workmate should take approximately 1 hour.
Before you proceed to assemble you will need the following tools.
1 - Hammer
1 - Phillips Screwdriver
1 - Nut Driver (supplied – item R of Fig.1))
1 - Combination Wrench (supplied) (not shown)
Fig. 1 : Unpack
Important: Check that you have received all the parts.
Remove the contents of the carton. The following components are in the carton.
(A) 1 - Frame Assembly 1 - Parts Bag containing:
(B) (H)2 - Vise Screw Packing Pieces 4- Top Blocks
(installed to (C) (I) ) 2- Top Blocks (one side flat)
(C) (J)2 - Vise Brackets 2- M6 x 36.5mm Bolts
1
588974-03,01,WM525* 9/24/04 2:07 PM Page 2
2
(D) (K)1 - Front Vise Jaw 2 - M6 x 30mm Bolts
(E) 1 - Middle Vise Jaw (narrow) (L) 4 - M6 Locking Nuts
(F) 1 - Rear Vise Jaw (wide) (M) 6 - M8 Bolts
(G) (N)2 - Wheels 4 - Swivel Grips
(O) 2 - Spring Pins
(P) 2 - Vise Hand Cranks
(Q) 2 - Snap-in Knobs
(R) 1 - Nut Driver
(S) 2 - M8 Wheel Nuts
(T) 2 - Flat Washer
(U) 2 - Vise Screw Protectors
(not shown) 1 - Combination Wrench
Assembly:
WARNING: Wear eye protection when assembling Workmate.
Fig. 2 & 3: Frame Assembly
1. Pick up the Frame Assembly Fig. 2: (A) as shown. Place foot on the lower portion of
the assembly and push the Transition Lever to the right to unlock the unit.
2. While holding the Transition Lever in the unlocked position, lift up on the upper cross
member until it is fully extended.
3. Rotate the upper cross member toward you and push back on the lower leg assembly
shown.
4. Fig. 3: Continue to push down on the upper cross member until the unit locks in the
fully open position.
5. Note! Make sure that the locking pin, is engaged and locked into the opposite
frame hole a click sound will be heard when locked in place.
Fig. 3: Wheel Assembly
1. Using Wheels , M8 Wheel Nuts , assemble to the axles as(G) (S) and Flat Washers (T)
shown.
Tighten the M8 Wheel Nuts using the Nut Driver (R).
Fig. 4: Assembly of the Vise Brackets
1. Assemble the left hand Vise Bracket as shown (Each bracket is stamped either (C)
LH or RH).
2. NOTE! The Vise Brackets must be in the “Tiltposition as shown to assemble to
the legs.
3. Pull vertical the locking button located on the side of the Vise Bracket back Fig. 15:
toward the handle end of the unit as shown in the inset, and lift up on the tilting
bracket, until the assembly locks into a vertical position.
4. Insert one M6 x 36.5mm Bolt Fig. 4: (J) through the rear leg of Frame Assembly, then
through the rear of the Vise Bracket as shown. Using a Phillips screwdriver and a
Combination Wrench, tighten the M6 Lock Nut (L) onto the bolt.
5. Assemble the front leg of the Frame Assembly to the front of the Vise Bracket (C) as
shown.
6. Insert one M6 x 30 mm Bolt (K) completely through the front leg assembly and then
through the hole in the side of the Vise Bracket as shown. Thread an M6 Lock Nut (L)
onto the end of the bolt and tighten with a Combination Wrench and Phillips screw driver.
7. Repeat for the right side (RH) Vise Bracket
Fig. 5: Assembling the Front Vise Jaw
1. Return the Tilt Bracket to the horizontal position by pulling the tilt lock button back to
disengage the lock and rotate the brackets back to the horizontal position as shown.
2. Assemble the front Top Blocks ( - one side flat) to the Front Vise Jaw (I) (D) as shown.
3. Thread an M8 Bolt through the jaw, then through the mounting block.(M)
4. While holding the Vise Screw and Pivot Nut up from the underside of the Tilt Bracket,
thread the M8 Bolt into the mounting hole in the pivot nut.
5. Tighten the M8 Bolts using the Nut Driver (R) (or Combination Wrench provided)
588974-03,01,WM525* 9/24/04 2:07 PM Page 3


Product specificaties

Merk: Black And Decker
Categorie: Niet gecategoriseerd
Model: WM525

Heb je hulp nodig?

Als je hulp nodig hebt met Black And Decker WM525 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Black And Decker

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd