Black And Decker FS1800ID Handleiding

Black And Decker Boormachine FS1800ID

Lees hieronder de 📖 handleiding in het Nederlandse voor Black And Decker FS1800ID (23 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/23

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust

. Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can

cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs

and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current

device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection.

Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench

or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables bet-

ter control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of dust collection

can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be

performed.

Use of the power tool for operations different from those intended could

result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by the manufacturer.

A charger that is

suitable for one type of battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together

may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid contact.

If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally

seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

Additional Specific Safety Rules

•Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a

"live" wire will make exposed metal parts of the tool "live" and shock the operator.

•Wear safety goggles or other eye protection. Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

•Bits, sockets and tools get hot during operation. Wear gloves when touching them.

•Do not operate this tool for long periods of time. Vibration caused by tool action may

be harmful to your hands and arms. Use gloves to provide extra cushion and limit

exposure by taking frequent rest periods.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from face and

body.

CAUTION: When not in use, place tool on its side on a stable surface where it will

not cause a tripping or falling hazard. Some tools with large battery packs will stand

upright on the battery pack but may be easily knocked over.

CAUTION: Wear appropriate personal hearing protection during use. Under some

conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety

glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETY EQUIPMENT:

•

ANSI Z87.1 eye protection (CAN/CSA Z94.3)

•

ANSI S12.6 (S3.19) hearing protection

•

NIOSH/OSHA/MSHA respiratory protection

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual.

The information it contains relates to protecting YOUR SAFETY and PREVENTING

PROBLEMS. The symbols below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situa-

tion which, if not avoided, may result in property damage

• The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

V..........volts A ..........amperes

Hz........hertz W ..........watts

min ......minutes ........alternating current

....direct current no ........no load speed

........Class II Construction …/min ..revolutions

........earthing terminal ..............per minute

........safety alert symbol BPM......beats per minute

Battery Cap Information

Battery storage and carrying caps are provided for use whenever the battery is out of the

tool or charger. Remove cap before placing battery in charger or tool.

WARNING: Do not store or carry battery so that metal objects can contact exposed

battery terminals. For example, do not place battery in aprons, pockets, tool boxes,

INSTRUCTION MANUAL

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTESADVERTENCIA:

DE USAR EL PRODUCTO.

CAT. NOS. BDID1202, BDID1802, FS1800ID, BDID182-CA FORM NO. 90532894

Cat. Nos.

BDID1202,

BDID1802,

FS1800ID,

BDID182-CA

Battery Cap

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A

SUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.

THANK

HANK YOU

YOU FOR

FOR CHOOSING

CHOOSING B

BLACK

LACK &

DECKER

ECKER!

OWWW

WWW.B

.BLACKAND

LACKANDD

DECKER

ECKER.

.COM

COM/N

/NEW

EWO

OWNER

WNER

OREGISTER

YOUR NEW

NEW PRODUCT

PRODUCT.

NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery

pack has not been kept on maintenance charge, it may need to be recharged before use. A

battery pack may also slowly lose its charge if left in a charger that is not plugged into an

appropriate AC source.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when

the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery

pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is

important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a

normal condition, and does not indicate a problem.

3. If the battery pack does not charge properly — (1) Check power at receptacle by

plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a

light switch which turns power off when you turn out the lights. (3) Move charger and

battery pack to a location where the surrounding air temperature is approximately

65°F - 75°F (18°- 24°C). (4) If charging problems persist, take or send the tool, battery

pack and charger to your local service center.

4. The battery pack should be recharged when it does not produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE use under these conditions.

Follow the charging procedures. You may also charge a partially used pack whenever

you desire with no adverse affect on the battery pack.

5. Black & Decker battery packs that are labeled “NiMH” should only be used with chargers

labeled “NiMH“ or “NiCd/NiMH.”

6. Under certain conditions, with the charger plugged into the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or

any buildup of metallic particles should be kept away from charger cavities. Always

unplug the charger from the power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

7. Do not immerse charger in water or any other liquid.

SAVE THESE INSTRUCTIONS

Operation

Variable Speed Trigger Switch (Fig. 1)

To turn the tool on, squeeze the trigger switch. To turn the tool off, release the trigger switch.

Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully

released. The variable speed switch enables you to select the best speed for a particular

application. The more you squeeze the trigger, the faster the tool will operate. Use lower

speeds for starting holes without a center punch, drilling in metals or plastics, or driving

screws. For maximum tool life, use variable speed only for starting holes or fasteners.

NOTE: Continuous use in variable speed range is not recommended. It may damage the

switch and should be avoided.

Forward/Reverse Control Button (FIG. 1)

A forward/reverse control button determines the direction of the tool and also serves as a

lock off button. To select forward rotation, release the trigger switch and depress the

forward/reverse control button on the right side of the tool. To select reverse, depress the

forward/reverse control button on the left side of the tool. The center position of the control

button locks the tool in the off position. When changing the position of the control button, be

sure the trigger is released.

Quick Release Chuck – (FIG. 2)

NOTE: The chuck accepts 1/4 in. (6.35 mm) hex accessories only.

Place the switch in the locked off (center) position or remove battery pack before changing

accessories.

To install an accessory, pull the chuck collar away from the front of the tool, insert the

accessory, and release the collar. The accessory is locked in place.

To remove an accessory, pull the chuck collar away from the front of the tool, remove the

accessory and release the collar.

Maintenance

Cleaning

With the motor running, blow dirt and dust out of all air vents with dry air. Wear safety

glasses when performing this procedure. Exterior plastic parts may be cleaned with a damp

cloth and mild detergent. Although these parts are highly solvent resistant, NEVER use

solvents.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service organizations, always using identical replacement

parts.

Accessories

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-54-HOW-TO (544-6986).

WARNING: The use of any accessory not recommended for use with this tool could

be hazardous.

CAUTION: Use only impact sockets. Non-impact sockets may break and cause a

hazardous condition. Inspect sockets prior to use to ensure that it

contains no cracks.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to

recycle the battery (or battery pack) at the end of its useful life have already been paid by

Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the

trash or municipal solid waste stream and the RBRC program provides an environmentally

conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent nickel-

cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service center

or to your local retailer for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery, or call 1-800-8-BATTERY.

product kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap.

Transporting batteries can possibly cause fires if the battery terminals inadvertently come

in contact with conductive materials such as keys, coins, hand tools and the like. The US

Department of Transportation Hazardous Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon

luggage) UNLESS they are properly protected from short circuits. So when transporting

individual batteries, make sure that the battery terminals are protected and well insulated

from materials that could contact them and cause a short circuit."

Important Safety Instructions

•SAVE THESE INSTRUCTIONS. This manual contains important safety and operating

instructions for BDMVC battery charger.

• Before using charger, read all instructions and cautionary markings on (1) charger, (2)

battery pack, and (3) product using battery pack.

DANGER: 120 volts present at charging terminals. Do not probe with conductive objects.

Danger of electric shock or electrocution.

DANGER: If battery pack case is cracked or damaged, do not insert into charger. Danger

of electric shock or electrocution.

DANGER: Never attempt to open the battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service center for recycling.

WARNING: Don’t allow any liquid to get inside charger. Electric shock may result.

CAUTION: To reduce risk of injury, charge only Black & Decker rechargeable batteries.

Other types of batteries may burst, causing personal injury and damage.

• To facilitate the cooling of the battery pack after use, avoid placing the charger or battery

pack in a warm environment such as in a metal shed, or an uninsulated trailer.

• Do not expose charger to rain or snow.

• Use of an attachment not recommended or sold by Black & Decker may result in risk of

fire, electric shock, or injury to persons.

• This charger is not intended for any uses other than charging Black & Decker rechargeable

batteries. Any other uses may result in risk of fire, electric shock or electrocution.

• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

• Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

• An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round

jacketed extension cords should be used, and we recommend that they be listed by

Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must

be suitable for outdoor use. Any cord marked for outdoor use can also be used for

indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable

for outdoor use.

b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety, and to prevent loss of power and overheating. The smaller the gauge number of

the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than

18 gauge. When using more than one extension to make up the total length, be sure

each extension contains at least the minimum wire size.

RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS

Total Extension Cord Length (feet)

25 50 75 100 125 150 175

Wire Gauge

18 18 16 16 14 14 12

• The charger is ventilated through slots in the housing. Do not place any object on top of

charger or place the charger on a soft surface that might block the ventilation slots and

result in excessive internal heat. Place the charger in a position away from any heat source.

• Do not operate charger with damaged cord or plug — have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service or repair

is required. Incorrect reassembly may result in risk of electric shock, electrocution or fire.

• The charger is designed to operate on standard 120 VAC, 60Hz household electrical

power. Do not attempt to use it on any other voltage.

• To reduce risk of electric shock, unplug charger from outlet before attempting any cleaning.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• DO NOT store or use the tool and battery pack in locations where the temperature may

reach or exceed 105°F (such as outside sheds or metal buildings in summer).

SAVE THESE INSTRUCTIONS

Introduction

Your charger is designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any

other voltage. Charge time is 90 to 120 minutes depending on battery pack type and condition.

Charging Procedure

1. Plug the charger into an appropriate outlet.

2. Insert the battery pack into the charger (Fig. A) . Be sure the pack is fully

seated in the charger. The red (charging) light will blink continuously indicating

that the charging process has started.

3. The completion of charge will be indicated by the red light remaining ON

continuously. The pack is fully charged and may be used at this time or left in

the charger.

Charge Indicators

Replace Pack:

These chargers are designed to detect certain problems that can arise with battery packs

which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert

battery pack. If problem persists, try a different battery pack to determine if the charger is OK. If

the new pack charges correctly, then the original pack is defective and should be returned to a

service center for recycling. If the new battery pack gives the same trouble indication as the

original, have charger tested at an authorized service center.

Wall Mounting (Figure B)

A hole is provided in the center of the

charger for mounting on a vertical surface.

Leaving the Battery Pack in the Charger

The charger and battery pack can be left connected with the red light glowing indefinitely. The

charger will keep the battery pack fresh and fully charged.

Fig.A

MOUNTING HOLE

Fig.B

1 2

•Variable Speed

Switch

•Interrupteur à vitesse

variable

•Conmutador de

velocidad variable

•Forward/Reverse

Button

•Bouton de

commande de

marche avant ou

marche arrière

•Botón de avance y

reversa

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Battery not installed properly. • Check battery installation.

• Battery not charged. • Check battery charging

requirements.

• Battery will not charge. • Battery not inserted into charger. • Insert battery into charger

until red LED appears.

• Charger not plugged in. • Plug charger into a working

outlet. Refer to “Important

Charging Notes” for more

details.

• Check current at receptacle

by plugging in a lamp or other

appliance.

• Check to see if receptacle is

connected to a light switch

which turns power off when

you turn out the lights.

• Surrounding air temperature • Move charger and tool to a

too hot or too cold. surrounding air temperature

of above 40 degree F(4,5°C)

or below 105 degree F

(+40,5°C).

For assistance with your product, visit our website www.blackanddecker.com for the loca-

tion of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Avertissements de sécurité généraux pour les outils

électriques

AVERTISSEMENT! Lire tous les avertissements de sécurité et toutes les

directives. Le non-respect des avertissements et des directives pourrait se solder

par un choc électrique, un incendie et/ou une blessure grave.

Conserver tous les avertissements et toutes les directives pour un usage

ultérieur.

Le terme «outil électrique» cité dans les avertissements se rapporte à votre outil

électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a) Tenir la zone de travail propre et bien éclairée.

Les endroits sombres sont souvent

des causes d'accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, soit en

présence de liquides inflammables, de gaz ou de poussière.

Les outils

électriques produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les curieux au moment d’utiliser un outil électrique.

Une

distraction pourrait vous en faire perdre la maîtrise.

2) Sécurité en matière d’électricité

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais

modifier la fiche en aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un

outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation

de fiches non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des

tuyaux, des radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc

électrique est plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à d'autres conditions où il

pourrait être mouillé.

La pénétration de l’eau dans un outil électrique augmente le

risque de choc électrique.

d) Ne pas utiliser abusivement le cordon d’alimentation. Ne jamais utiliser le

cordon pour transporter, tirer ou débrancher un outil électrique. Tenir le cordon

éloigné de la chaleur, de l’huile, des bords tranchants ou des pièces mobiles.

Les cordons endommagés ou emmêlés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à une telle utilisation.

L’utilisation d’une rallonge conçue pour l’extérieur

réduit les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, utiliser une source d’alimentation dotée d’un disjoncteur de fuite à la

terre.

L’utilisation de ce type de disjoncteur réduit les risques de choc électrique.

3) Sécurité personnelle

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un

outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou

sous l’influence de drogues, d’alcool ou de médicaments.

Un simple moment

d’inattention en utilisant un outil électrique peut entraîner des blessures corporelles

graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une

protection oculaire.

L’utilisation d’équipements de protection comme un masque

antipoussière, des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert réduira les risques de blessures

corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à

la position d’arrêt avant de relier l’outil à une source d’alimentation et/ou

MODE D’EMPLOI

CONSERVER CE MANUEL POUR UN USAGE ULTÉRIEUR.

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUE CE SOIT, COMPOSER LE

1-800-544-6986

AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART DES

CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR

TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS

IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.

MERCI

ERCI D

D’

’A

AVOIR

VOIR CHOISI

CHOISI B

BLACK

LACK & D

& DECKER

ECKER !

VISITEZ

ISITEZ WWW

WWW.B

.B LACKAND

LACKANDD

DECKER

ECKER.

.COM

COM/N

/NEW

EWO

OWNER

WNER

POUR

POUR ENREGISTRER

ENREGISTRER VOTRE

VOTRE NOUVEAU

NOUVEAU PRODUIT

PRODUIT.

S-

-É

ÉC

N° de catalogue BDID1202, BDID1802, FS1800ID, BDID182-CA

d’insérer un bloc-piles, de ramasser ou de transporter l’outil.

Transporter un outil

électrique alors que le doigt repose sur l’interrupteur ou brancher un outil électrique

dont l’interrupteur est à la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé standard avant de démarrer l’outil.

Une clé

standard ou une clé de réglage attachée à une partie pivotante peut causer des blessures.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps.

Cela permet

de mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de

bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces

mobiles.

Les vêtements amples, les bijoux ou les cheveux longs risquent de rester

coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de dispositifs de

dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés et

utilisés.

L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers

engendrés par les poussières.

4) Utilisation et entretien d’un outil électrique

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à

l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus

sûre et à la vitesse pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux.

Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche du secteur ou le bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire, ou avant de ranger l’outil

électrique.

Ces mesures préventives réduisent les risques de démarrage accidentel

de l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants, et ne permettre à

aucune personne n’étant pas familière avec un outil électrique (ou son manuel

d’instruction) d’utiliser ce dernier

. Les outils électriques deviennent dangereux

entre les mains d’utilisateurs inexpérimentés.

e) Entretenir les outils électriques. Vérifier les pièces mobiles pour s’assurer

qu’elles sont bien alignées et tournent librement, qu’elles sont en bon état et ne

sont affectées par aucun trouble susceptible de nuire au bon

fonctionnement de l’outil électrique

En cas de dommage, faire réparer l’outil

électrique avant toute nouvelle utilisation.

Beaucoup d’accidents sont causés par

des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres.

Les outils de coupe

bien entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles

à contrôler.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail à

effectuer.

L’utilisation d’un outil électrique pour toute opération autre que celle pour

laquelle il a été conçu est dangereuse.

5) Utilisation et entretien du bloc-piles

a) Ne recharger l’outil qu’au moyen du chargeur précisé par le fabricant.

L’utilisation

d’un chargeur qui convient à un type de bloc-piles risque de provoquer un incendie s’il

est utilisé avec un autre type de bloc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-piles conçus à cet effet.

L’utilisation de tout autre bloc-piles risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné des objets métalliques,

notamment des trombones, de la monnaie, des clés, des clous, des vis, etc., qui

peuvent établir une connexion entre les deux bornes.

Le court-circuit des bornes

du bloc-piles risque de provoquer des étincelles, des brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors du bloc-piles, éviter tout

contact. Si un contact accidentel se produit, laver à grande eau. Si le liquide

entre en contact avec les yeux, obtenir des soins médicaux.

Le liquide qui gicle

hors du bloc-piles peut provoquer des irritations ou des brûlures.

6) Réparation

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que

des pièces de rechange identiques

. Cela permettra de maintenir une

utilisation sécuritaire de l’outil électrique.

Règles de sécurité particulières

•Saisir l’outil par ses surfaces de prises isolées lorsque l’outil peut entrerélectrique

en contact avec des fils cachés ou son cordon. En cas de contact avec un fil sous

tension, les pièces métalliques de l’outil seront sous tension et l’utilisateur subira des

secousses électriques.

•Toujours porter des lunettes de protection ou toute autre protection oculaire. Lors du

martelage ou du perçage, des débris sont rejetés dans l’air. Ces derniers peuvent causer

des dommages oculaires permanent.

•Mèches, douilles ou outils peuvent chauffer pendant leur utilisation. Toujours porter

des gants avant de les manipuler.

•Ne pas utiliser cet outil pendant des périodes prolongées. Les vibrations causées par

l’outil peuvent poser des risques pour les mains ou les bras. Porter des gants pour amortir les

vibrations, et pour limiter les risques faire des pauses fréquentes.

AVERTISSEMENT : certains outils électriques, tels que les sableuses, les scies, les

meules, les perceuses ou certains autres outils de construction, peuvent produire

de la poussière contenant des produits chimiques reconnus par l’État de la

Californie comme étant susceptibles d’entraîner le cancer, des malformations

congénitales ou pouvant être nocifs pour le système reproductif. Parmi ces

produits chimiques, on retrouve :

· le plomb dans les peintures à base de plomb,

· la silice cristalline dans les briques et le ciment et autres produits de maçonnerie,

· l’arsenic et le chrome dans le bois de sciage ayant subi un traitement chimique.

Le risque associé à de telles expositions varie selon la fréquence avec laquelle on effectue

ces travaux. Pour réduire l’exposition à de tels produits, il faut travailler dans un endroit bien

aéré et utiliser le matériel de sécurité approprié, tel un masque anti-poussières

spécialement conçu pour filtrer les particules microscopiques.

•Éviter tout contact prolongé avec la poussière soulevée par cet outil ou autres

outils électriques. Porter des vêtements de protection et nettoyer les parties

exposées du corps avec de l’eau savonneuse. S’assurer de bien se protéger afin

d’éviter d’absorber par la bouche, les yeux ou la peau des produits chimiques nocifs.

AVERTISSEMENT : cet outil peut produire et répandre de la poussière susceptible

de causer des dommages sérieux et permanents au système respiratoire. Toujours

utiliser un appareil respiratoire anti-poussières approuvé par le NIOSH ou l’OSHA. Diriger

les particules dans le sens opposé du visage et du corps.

MISE EN GARDE : Après utilisation, ranger l’outil sur son côté sur une surface

stable là où il ne pourra faire ni trébucher ni tomber personne. Certains outils équipés

d’un large bloc-pile peuvent tenir à la verticale sur ce dernier mais ils sont alors facilement

déstabilisés.

MISE EN GARDE : Porter des protecteurs d’oreilles appropriés durant l’utilisation.

Selon les conditions et la durée d’utilisation, le bruit émis par cet outil peut causer une perte

auditive.

AVERTISSEMENT : TOUJOURS porter des lunettes de sécurité. Les lunettes de

vue ne constituent PAS des lunettes de sécurité. Utiliser également un masque

facial ou anti-poussière si l’opération de découpe génère de la poussière. TOU-

JOURS PORTER UN ÉQUIPEMENT DE PROTECTION HOMOLOGUÉ :

• protection oculaire conforme à la norme ANSI Z87.1 (CAN/CSA Z94.3);

• protection auditive ANSI S12.6 (S3.19);

• protection des voies respiratoires conformes aux normes NIOSH/OSHA/MSHA.

LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS

Il est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il

contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les

symboles ci-dessous servent à vous aider à reconnaître cette information.

DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas évitée,

causera la mort ou des graves blessures.

AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle n’est

pas évitée, pourrait causer la mort ou de graves blessures.

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide customers

with efficient and reliable power tool service. Whether you need technical advice, repair, or

genuine factory replacement parts, contact the Black & Decker location nearest you. To find

your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material

or workmanship. The defective product will be replaced or repaired at no charge in either of

two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should be

made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after

the sale). Proof of purchase may be required. Please check with the retailer for their specific

return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may be

required. Black & Decker owned and authorized Service Centers are listed under "Tools-

Electric" in the yellow pages of the phone directory and available on our website

www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center. This product

is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-544-6986 for a free replacement.

Product specificaties

Merk:	Black And Decker
Categorie:	Boormachine
Model:	FS1800ID

Heb je hulp nodig?

Als je hulp nodig hebt met Black And Decker FS1800ID stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Black And Decker

Black And Decker TP550 Handleiding

26 Augustus 2024

Black And Decker TP555 Handleiding

26 Augustus 2024

Black And Decker BEH850 Handleiding

10 Juni 2024

Black And Decker DCD709 Handleiding

17 Augustus 2023

Black And Decker BDCDD18N Handleiding

20 Juni 2023

Black And Decker XTC143BK Handleiding

18 Juni 2023

Black And Decker HPD1800 Handleiding

18 Juni 2023

Black And Decker 7157 Handleiding

17 Juni 2023

Black And Decker KR2000K Handleiding

16 Juni 2023

Black And Decker KD354CRE Handleiding

16 Juni 2023

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Makita DDF459 Handleiding

21 December 2024

Total TRHLI1601 Handleiding

16 December 2024

Black Decker 1963 Handleiding

8 December 2024

Black Decker 1350-09 Handleiding

8 December 2024

Gude GTB 16/5 R Handleiding

8 December 2024

Hikoki DV36DA Handleiding

7 December 2024

Hikoki DH26PC2 Handleiding

7 December 2024

Hikoki DH28PCY2 Handleiding

7 December 2024

Zipper ZI-BHA1500DN Handleiding

7 December 2024

Bavaria BRH 850 Handleiding

5 December 2024