Black And Decker BDS200 Handleiding

Black And Decker Detector BDS200

Lees hieronder de 📖 handleiding in het Nederlandse voor Black And Decker BDS200 (43 pagina's) in de categorie Detector. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/43

www.blackanddecker.eu

English 3

Deutsch 6

Français 10

Italiano 13

Nederlands 16

Español 19

Português 22

Svenska 25

Norsk 28

Dansk 31

Suomi 34

Ελληνικά 37

ENGLISH

Intended use

This Black & Decker tool has been designed to aid in locating

live wires operating at mains voltage (230 V AC) and metal

pipes behind internal walls. This tool is intended for consumer

use only.

Safety instructions

 Warning! When using battery-powered tools, basic safety

precautions, including the following, should always be

followed to reduce the risk of ﬁre, leaking batteries,

personal injury and material damage.

 Read all of this manual carefully before operating the tool.

 Retain this manual for future reference.

Keep work area clean

Cluttered areas and benches can cause accidents.

Consider work area environment

Do not expose the tool to rain. Do not use the tool in damp or

wet conditions. Keep the work area well lit. Do not use the

tool where there is a risk of causing ﬁre or explosion, e.g. in

the presence of ﬂammable liquids and gases.

Keep children away

Do not allow children, visitors or animals to come near the

work area or to touch the tool.

Do not overreach

Keep proper footing and balance at all times.

Stay alert

Watch what you are doing. Use common sense.

Do not operate the tool when you are tired.

Use appropriate tool

The intended use is described in this instruction manual.

Warning! The use of any accessory or attachment or

performance of any operation with this tool other than those

recommended in this instruction manual may present a risk of

personal injury.

Check for damaged parts

Before use, carefully check the tool for damage. Ensure that

the tool will operate properly and perform its intended function.

Do not use the tool if any part is damaged or defective.

Store idle tools

When not in use, tools and batteries should be stored in a dry,

locked up or high place, out of reach of children.

Repairs

This tool complies with relevant safety requirements.

Repairs should only be carried out by qualiﬁed persons using

original spare parts; otherwise this may result in considerable

danger to the user.

Additional safety instructions for non-rechargeable

batteries

 Never attempt to open for any reason.

 Do not store in locations where the temperature may

exceed 40 °C.

 When disposing of batteries, follow the instructions given

in the section "Protecting the environment". Do not

incinerate the batteries.

 Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries, proceed as

follows:

- Carefully wipe the liquid off using a cloth.

Avoid skin contact.

Additional safety instructions for pipe and wire

detectors

 Do not use the tool to detect AC voltage in uninsulated,

exposed or free wires.

 Do not use the tool as a substitute for a voltmeter.

 Be aware that the tool may not always properly detect all

pipes and wires. The following conditions can cause

inaccurate results:

- Low battery

- Thick walls with thin pipes or wires

- Very thick walls

- Very deep wires or pipes

- Walls covered with metal

- Very humid conditions

- Shielded cables

 Before use, always test the tool by detecting a known pipe

or wire.

 If in doubt contact a qualiﬁed contractor.

Warning! This tool will not detect wires in circuits isolated

from the mains supply, cables operating at direct current (DC)

or wires used for telecommunication or computer systems.

Hidden wires (e.g. wall lights) may not be detected when

switches are in the off position.

Warning! This tool will not detect pipes of any other material

than metal.

Features

1. Mode selector switch

2. LED indicator

3. Sensitivity dial

Fig. A

4. Battery cover

Assembly

Fitting the battery (ﬁg. B)

 Slide the battery cover (4) off the tool.

 Connect the battery to the connector. The larger battery

terminal connects to the smaller connector terminal.

Product specificaties

Merk:	Black And Decker
Categorie:	Detector
Model:	BDS200
Kleur van het product:	Black, Red
Accu/Batterij voltage:	9 V
Aantal per verpakking:	1 stuk(s)
Batterijtechnologie:	Alkaline
Detecteerbare materialen:	Ferrous metal, Live cable
Maximum detectie diepte (live kabel):	50 mm
Maximum detectie diepte (koper):	25 mm
Maximum detectie diepte (staal):	50 mm