Black And Decker 9049 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Black And Decker 9049 (27 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/27
INFORMACIONS CLAVE
QUE DEBE SABE
.
El taladro debe cargarse durante
16 hor.
El taladro viene con el interruptor
trabado en posición de apagado
Antes de intentar usario, vea
página 18.
Apriete el portabrocas utilzando
los tres agujeros.
RENSEIGNEMENTS
IMPORTANTS
G U I D E D ' U T I L I S A T I O N
1 8 0 0 7 6 2 - 6 6 7 2
Il faut charger la perceuse pendant 16
heyres avant la première utilisation.
L’interrupteur de la perceuse est
verrouillé en position d’arrêt à sa
sortie de l’`eusine. Lire la page 9
avant d’utiliser la perceuse.
Resserrer le mandrin dans vchacun
des troistrous.
PERCEUSE SANS FIL À
2 VITESSES DE 4,8/6,0
VOLTS
TALADRO INALAMBRICO DE
4,8/6,0 VOLTS DE 2
VELOCIDADES
AVERTISSEMENT : POUR S'ASSURER
DU FONCTIONNEMENT SÛR, LIRE
GUIDE D'UTILISATION. POUR
OBTENIR DE PLUS AMPLES
RESEIGNEMENTS, COMPOSER SANS
FRAIS LE NURO SUIVANT.
I9049
9049
9049 Form No. 154433 MAR95-CO-1 Copyright © 1995 Printed in U.S.A.
9 1 - 8 0 0 - 7 0 1 - 2 8
INSTRUCTIVO DE OPERACIÓN,
CENTROS DE SERVICIO Y LIZA DE
GARANTÍA.
ADVERTENCIA: ASE ESTE
INSTRUCTIVO ANTES DE USAR EL
PRODUCTO. SI TIENE DUDAS, POR
FAVOR LLAME.
MANUAL DE INSTRUCCIONES
154433/-9049 SHORT2 12/8/03 10:05 AM Page 2
EN G L I S H
KEY INFORMATION
YOU SHOULD KNOW
9 0 4 9
I N S T R U C T I O N M A N U A L
WARNING: FOR SAFE OPERATION
READ INSTRUCTION MANUAL.
IF YOU HAVE ANY QUESTIONS,
CALL US TOLL FREE: 1 - 8 0 0 - 7 6 2 - 6 6 7 2
Drill must be charged for 16 hours before
initial use.
Drill is shipped with switch locked off.
Before attempting to use drill, see page 2.
Tighten chuck using all three holes.
4.8 VOLT 2-SPEED CORDLESS DRILL
6.0 VOLT 2-SPEED CORDLESS DRILL
VEA EL ESPAÑOL EN LA
CONTRAPORTADA.
POUR LE FRANÇAIS, VOIR LA
COUVERTURE ARRIÉRE.
154433/-9049 SHORT2 12/8/03 10:05 AM Page 3
SECURE WORK. Use clamps or a vise to hold work. It’s safer than
using your hand and it frees both hands to operate tool.
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for
better and safer performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords periodically and if
damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep
handles dry, clean, and free from oil and grease.
DISCONNECT OR LOCK OFF TOOLS when not in use, before
servicing, and when changing accessories, such as blades, bits,
cutters.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of
checking to see that keys and adjusting wrenches are removed
from tool before turning it on.
AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger
on switch. Be sure switch is off when plugging in.
EXTENSION CORDS. Make sure your extension cord is in good
condition. When using an extension cord, be sure to use one
heavy enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size
to use depending on cord length and nameplate ampere rating. If
in doubt, use the next heavier gage. The smaller the gage number,
the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more AWG
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
EN G L I S H
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric tools, basic safety precautions should
always be followed to reduce risk of fire, electric shock, and personal
injury, including the following:
READ ALL INSTRUCTIONS
Safety Instructions For All Tools
KEEP WORK AREA CLEAN. Cluttered areas and benches invite
injuries.
CONSIDER WORK AREA ENVIRONMENT. Don’t expose power
tools to rain. Don’t use power tools in damp or wet locations. Keep
work area well lit. Do not use tool in presence of flammable liquids
or gases.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with
grounded surfaces. For example; pipes, radiators, ranges, and
refrigerator enclosures.
KEEP CHILDREN AWAY. Do not let visitors contact tool or extension
cord. All visitors should be kept away from work area.
STORE IDLE TOOLS. When not in use, tools should be stored in dry,
and high or locked-up place — out of reach of children.
DON’T FORCE TOOL. It will do the job better and safer at the rate
for which it was intended.
USE RIGHT TOOL. Don’t force small tool or attachment to do the
job of a heavy-duty tool. Don’t use tool for purpose not intended.
DRESS PROPERLY. Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and non-skid footwear
are recommended when working outdoors. Wear protective hair
covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if operation is
dusty.
DON’T ABUSE CORD. Never carry tool by cord or yank it to
disconnect from receptacle. Keep cord from heat, oil, and sharp
edges.
1
154433/-9049 SHORT2 12/8/03 10:05 AM Page 1


Product specificaties

Merk: Black And Decker
Categorie: Boormachine
Model: 9049

Heb je hulp nodig?

Als je hulp nodig hebt met Black And Decker 9049 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Boormachine Black And Decker

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine