Bintec-elmeg S530 Handleiding

Bintec-elmeg Telefoon S530

Lees hieronder de 📖 handleiding in het Nederlandse voor Bintec-elmeg S530 (2 pagina's) in de categorie Telefoon. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

xDSL

elmeg hybird System

Internet

Public

network

5500001619 - V. 1.4

 The connectors for the receiver and the headset must be inserted prior to fixing

the wall bracket.

 Fix the unit to a flat wall. It is important that you get the distances between the drill

holes absolutely accurate.

 The wall brackets are screwed on underneath, at the back of the system telephone.

 The system telephone is supplied without the receiver brackets for wall mounting.

 To mount the system telephone on the wall, the receiver bracket needs to be

replaced by the receiver bracket from the assembly kit. To change it over, it can

be pulled gently upwards and out.

Refer to the manual for information on installation.

Wall mounting

 Note the ambient temperature for storing and operating the device in the specifications.

The device must only be connected once the permissible ambient operating temperature

is reached.

 Please note that condensation may form on or within the device during transitions from

cold to warm temperatures . Only remove the device from the packaging when the

permissible ambient operating temperature has been reached.

 During a storm, you should not connect or disconnect any cables and do not make

any calls.

 Only connect the cords to the connectors provided.

 Position the cords where they will not cause accidents.

 Avoid the following influencing factors:

- Direct sunlight

- Heat sources (e. g. heating elements)

- Electronic devices (e. g. sound systems, office equipment or microwaves)

- Penetration of humidity or liquids

- Corrosive liquids or vapours

- High levels of dust

 Do not use the device in humid or explosive areas.

 Only open those parts of the unit which are shown in the assembly/operating instructions.

 Do not touch the plug contacts with sharp, metal or damp objects.

 If the device is not permanently mounted, position the device or the accessory on a

non-slip surface.

 Only clean the device with the antistatic cloth provided.

 Use approved accessories only.

 Only terminals that offer SELV (safety extra low voltage) and/or comply with ETS

300047 may be connected to the device. Proper use of approved terminals complies

with this directive.

Plug power supply unit

 Only use the plug power supply unit which is available as an accessory.

 Do not use any plug power supply units that show signs of damage (breaks or cracks

in the casing).

Electrostatic charges (ESD protection)

 The ESD protection that the supplied system telephone has against the effects of

electrostatic charges is greater than certification values. Nonetheless, you should avoid

excessive static charges. Various causes can result in the electrostatic charge achieving

values that far exceed the permissible values required and that exceed the system

telephone's interference immunity. Such causes or circumstances, such as low humidity

and carpets, must be eliminated. The manufacturer of the system telephone accepts

no liability for damages resulting from these causes.

Mount and connect

The system telephone can be used as a desk or wall unit.

An assembly kit (not supplied) is required to attach it to a wall.

Connection sockets for S0 / Up0: The socket for selecting the connection is

located on the underside of the system telephone. Here you can select between

the S0 and Up0 connection. To do this, you press the module's two (2) clips

together, take the module out and, depending on the connection type, turn it

round and put it back in.

The picture shows the connector for S0.

The external S0 connector is connected to the »Line in« socket.

Another ISDN system telephone or ISDN telephone can be connected to the

"Line out" socket.

The maximum length of the cable to the telephone here is 10 metres.

In order to operate your system telephone, you must insert the cords for the

telephone connector and the receiver.

Connect your telephone to the S0 or Up0 connector.elmeg hybird system's

Label strips: Two hooks are used to put the cover into the holder for label

strips, and a magnet is used to secure it on the underside

Headset: You can connect a headset to the system telephone (not supplied).

Connect the headset to the headset socket on the system telephone. Then

insert the headset cable into the cable guide and secure it beneath the cable

retainers.

 Line-in connection socket: Either S0 or Up0

 Line-out connection socket: S0 in every mode

 Mini USB connection (latest release)

 Receiver port (handset)

 Headset connector

 Socket for the plug power supply unit (accessory)

Required for the 1st and subsequent T500 key extension on

the elmeg S530 / elmeg S560 and for installations for which

the existing power supply is insufficient.

Available connections

Receiver bracket Wall bracket

System telephones

elmeg S560 / elmeg S530

 system telephoneelmeg S560 / S530

 Receiver with cord

 Base

 One connector cord with RJ45 plugs

 Installation instructions

 Antistatic cloth

Assembly kit (not supplied)

 10 wall brackets

 5 receiver brackets

 20 screws for connecting the

system telephone to the wall brackets

 10 wood screws 3x30

 10 dowels for 5 mm holes

 1 drilling template

*elmeg S530 has a 4-line graphic display with LED backlight

1 System telephone

2 Display

3 8-line graphic display with LED backlight*

4 Loudspeaker port

5 Function keys with LED

6 Label field

7 Microphone

8 Cradle switch

9 Magnetic clamp in label field

10 Softkeys

11 + / - keys for settings

12 Key for loudspeaker / hands-free

13 Home key

14 Redial key

15 Headset key

16 Hold key

17 Mail key

18 Navigator with OK key

19 Dialling keys

20 Blue status LED

Safety information

Contact

Scope of supply

elmeg S560 / S530 System Telephone - Installation

Functions

Lift receiver, turn on Hands-free, turn on headset, or start preparatory

dialling. When you enter a number to dial via an SIP provider, the output is only dialled

around 5 seconds after entering the last digit. If you end the call number

with the hash key, the system dials automatically. The terminal must be able

to dial the hash key in to the telephone system.

Use the Home key to go back to the Idle menu.

When idle, the device info is displayed.

Keys Keys

Replace receiver, turn off hands-free or turn off headset.

The system telephone is in idle status

A call is signalled. The call melody sounds.

You are in a call.

You hear the positive or negative acknowledge tone.

A conference call is initiated.

Key 0-9, * or #: Choose call number, code, character or text.

You can use this key to protect the system telephone from

certain types of use.

You can use the Navigator to navigate in the display.

Softkeys. The softkeys' available functions are shown in the bottom row in

the display.

The OK key is used to confirm and save inputs.

From the Idle menu, pressing twice opens the phone book.

You can use the hold key to go from a call to a hold for enquiry.

Pressing the key again terminates the hold and you are once more connected

with the person you were first speaking to.

When the receiver is hung up:

Use the Redial Last Number key to dial the last number dialled again.

When the receiver is off the hook:

Use the Redial Last Number key to display the last 30 numbers dialled.

Use the Mail key to query the system's voicebox.

When the key's blue LED flashes, it means there are new messages.

The Headset key is used to switch the headset on and off.

These keys are used to adjust the volume and the display.

The Loudspeaker key is used to switch the hands free

or loudspeaker on and off.

Manual, software and workshops:

You will find the latest manual, the Dime Manager and additional information on our website

at www.bintec-elmeg.com.

Contact:

If you have any questions about your new product, or if you require further information,

the bintec elmeg GmbH Support Centre can be reached Monday to Friday, between the

hours of 9 am and 5 pm, at

Telephone: +49 911 9673 0

Fax: +49 911 688 0725

For detailed information about our support and service offers please visit our website

at www.bintec-elmeg.com.

Navigation

Use the "Up" and "Down" Navigator to select a row in the display.

This row is highlighted.

Select the highlighted row

If there is a + sign to the left of the row, the next menu for the selected

row will appear if you press the "Right" Navigator.

Return to the previous menu

Use the "Left" Navigator

the "Back" softkey to skip back to the previous display.

If you press the "Home" key you return to the initial menu (the system

telephone's idle status). Any existing function is aborted.

Delete contents

You can use the Navigator to select a row in the display.

Use the "Delete"softkey to delete the content of the selected row and

return to the previous display.

View options

Use the "Options" softkey to go to the next menu. Special functions or

information items are provided here.

Status LED

If the two blue LEDs in the status display are flashing fast, data is being saved

in the system telephone or shared with the .elmeg hybird

While this is happening, it is important that the power supply

to the system telephone is not cut off.

The receiver is hung up or lifted.

Select "Settings" with the Navigator.

Select "Menu" with the softkey.

Use the "Right" Navigator to display the next menu

for the selected row.

Entering settings

Select "Call numbers" with the Navigator.

Use the "Right" Navigator to display the next menu

for the selected row.

Call numbers

Use the Navigator to select the number of your system

telephone which you wish to view.

Use the "Right" Navigator to display the next menu

for the selected row.

Enter call number 1

Use the Navigator to select the row you wish to view.

Use the "Right" Navigator to display the next menu

for the selected row.

Use the dialling keys to enter the name for the system

telephone's internal number.

The OK key is used to save the name, and you go

back to the "1st call number" menu.

Name

Use the Navigator to select the entry you wish to edit.

Ring tone internal / external,

Sound volume internal / Sound volume external.

Use the "Right" Navigator to display the next menu

for the selected row.

Melody

Use the dialling keys to enter the system telephone's

internal number.

The OK key is used to save the number, and you go

back to the "1st call number" menu.

View the call number

Use the "Back" softkey or the "Left" Navigator to return to

the "1st call number" menu.

Select the melody you want (1 - 20) using the +/- keys.

The melody you select is shown, as a number, on the

right.

Ring tone internal

Use the "Back" softkey or the "Left" Navigator to return to

the "Melody" menu.

Press the +/- keys to set the desired volume.

The settings range from 1 - 10.

Sound volume internal

The OK key is used to save the volume, and you go back

to the "Melody" menu.

Select "Call waiting" with the Navigator.

Use the "Right" Navigator to display the next menu

for the selected row.

Call waiting

Use the Navigator to select the function you wish to edit:

Internal calls, external calls, repeat.

Use the "Right" Navigator to display the next menu

for the selected row.

Use the Navigator to select the function you wish

to switch on.

On: The call waiting tone sounds for any call,

for the duration of the call.

Off: The call waiting is signalled once.

The tick at the end of the row indicates which function

is enabled.

The OK key is used to save the function, and you

go back to the "Call waiting" menu.

Repeat

Select "Headset" with the Navigator.

Use the "Right" Navigator to display the next menu

for the selected row.

Headset

Use the Navigator to select the headset you wish to use:

No headset, Standard headset, DSHG/EHS headset.

The tick at the end of the row indicates which function is

enabled.

Headset

The OK key is used to save the function, and you go

back to the "Headset" menu.

If you have connected a headset to your system telephone,

you can use Auto Answer so that the headset is automatically

used for certain operations .

Off: The connection via the headset is not automatically

accepted, only after the headset has been switched on.

On: The connection via the headset is accepted immediately.

Delayed: The connection via the headset is accepted after

the time specified.

Use automatically

Select "Quick-Dial" with the Navigator.

Use the "Right" Navigator to display the next menu

for the selected row.

Quick-Dial

Select "On" or "Off" with the Navigator.

The tick at the end of the row indicates which setting is

enabled.

The OK key is used to save the function, and you

go back to the "Settings" menu.

Acknowledge tone

Select "Auto answer" with the Navigator.

Use the "Right" Navigator to display the next menu

for the selected row.

Auto answer

Use the Navigator to select the row you wish to edit.

Off: Auto answer is switched off.

On: The call is immediately accepted.

Delay: You do not wish to accept the call immediately, but

rather after a little time.

The OK key is used to save the setting, and you go back

to the "Settings" menu.

Press the +/- keys to specify the delay you want in 5

second increments. The value set is displayed to the

right in the row. The settings range from 0 - 20.

The OK key is used to save the setting, and you go back

to the "Auto answer" menu.

Important menu settings

Use the Navigator to select the row you wish to edit.

On: The acknowledge tone is always switched on.

Off: The acknowledge tone is switched off.

Error tone only: The acknowledge tone is only switched on

for incorrect entries.

The tick at the end of the row indicates which setting is

enabled.

The OK key is used to save the setting, and you go back

to the "Settings" menu.

Select "Acknowledge tone" with the Navigator.

Use the "Right" Navigator to display the next menu

for the selected row.

Use the Navigator to select the function you wish to

switch (on / off). The tick at the end of the row indicates

which function is enabled.

The OK key is used to save the function, and you

go back to the "Call waiting" menu.

Call waiting (internal calls / external calls)

Press the +/- keys to set the desired volume.

The settings range from 1 - 10.

Sound volume external

The OK key is used to save the volume, and you go back

to the "Melody" menu.

Select the melody you want (1 - 20) using the +/- keys.

The melody you select is shown, as a number, on the

right.

Ring tone external

Use the "Back" softkey or the "Left" Navigator to return to

the "Melody" menu.

Select "Suppress call number" with the Navigator.

Use the "Right" Navigator to display the next menu

for the selected row.

Suppress call number

Select "On" or "Off" with the Navigator. The tick at the

end of the row indicates which function is enabled.

The OK key is used to save the setting, and you go back

to the "Settings" menu. Before the row with your

telephone's name, you will see the symbol for the

suppressed number (the number combination "123",

crossed out).

Advanced functions

Product specificaties

Merk:	Bintec-elmeg
Categorie:	Telefoon
Model:	S530
Kleur van het product:	Zwart
Ingebouwd display:	Ja
Gewicht:	980 g
Breedte:	265 mm
Diepte:	220 mm
Hoogte:	120 mm
Soort:	Analoge telefoon
Resolutie:	128 x 36 Pixels
Touchscreen:	Nee
Montagewijze:	Bureau/muur
Microfoon mute:	Ja
Nummerherkenning:	Nee
Tekstregels:	4 regels
Geheugenkaart slot(s):	Nee
Backlight toetsen:	Ja
Ouderentelefoon:	Nee
Capaciteit telefoonboek:	- entries
Opnieuw bellen:	Ja
Aantal handsets inclusief:	1
Draadloze verbindingen:	Nee
Antwoordapparaat:	Nee
Programmeerbare hot keys:	Ja
Stroomverbruik (typisch):	1 W
Display met achtergrondverlichting:	Ja