Benro B1 Handleiding

Benro Statief B1

Lees hieronder de 📖 handleiding in het Nederlandse voor Benro B1 (2 pagina's) in de categorie Statief. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

B Series Double-Action Ballheads

75 Virginia Road

North White Plains, NY 10603

T 914.347.3300

F 914.347.3309

info@BenroUSA.com

BenroUSA.com

Operating Instructions

Thank you for making Benro your choice for professional photographic

equipment. Your Benro gear is manufactured to provide years

of dependable service. In order to obtain optimum satisfaction and

performance, we suggest that you carefully read these instructions.

Speciﬁcations and design are subject

to change without notice.

Mounting Screw

Stop Screws (2)

Head Locking Knob

Mounting Screw

Mounting Platform

Bubble Level

SETUP

Head Mounting

Install by screwing the head clockwise onto

the 3/8" Mounting Thread of the Top Plate of

the Tripod or Monopod. Once it is hand tight,

secure by fully tightening the Head Locking

Screw(s) (on select models) from below.

OPERATION

The B Series Double-Action Ballheads are

professional black anodized machined

aluminum and feature three operating

Knobs. Drag control is manually adjusted

and locked, along with independent

Panning. Plus a Universal Quick Release

Clamp with secondary Safety Lock System

is incorporated.

Universal Quick Release Plate System

The B Series Double-Action Ballheads

feature a Universal Quick Release Plate

system. It offers a quick method of

mounting or releasing a Camera or

Equipment from the Head. It’s important

that the correct Quick Release Plate be used

along with the proper mounting screw

(1/4–20 is included as the standard size

but spare 1/4–20 and 3/8 plates of various

lengths are available as accessories). Extra

Plates are recommended as you can screw

one to each Camera or Lens for even greater

convenience when rapidly mounting

and dismounting gear. And because of

compatibility with the Universal system,

most plates and special brackets from other

manufacturers can be used as well.

Quick Release Lock (FIGURE 1)

When used properly, the Quick Release

Lock offers two levels of security for your

gear. To remove the Quick Release Plate,

turn the Quick Release Locking Knob

counter-clockwise. A partial opening of

the clamping mechanism allows the Quick

Release Plate to slide on the Mounting

Platform for proper balance and positioning.

Two Stop Screws (removable) on the bottom

of the Quick Release Plate provide this first

level of security. An additional counter-

clockwise turn of the Quick Release Locking

Knob opens the clamp fully so that the

Quick Release Plate can be tilted out to

be removed. Reverse the process and

tighten the Quick Release Locking Knob

to secure the Quick Release Plate.

Ballhead Controls (FIGURE 2)

A large Head Locking Knob locks the

Ballhead in place. Once the Knob is

turned counter-clockwise and loosened,

the Ballhead can move freely allowing

the Mounting Platform to be positioned

anywhere within a 0–90° vertical

orientation. This movement is expanded by

the use of the Pan Locking Knob

which adds a 360° Panning range. The Pan

control is fully independent and positioning

can be adjusted easily and accurately by

using the Graduated Panning Scale and

Pointer on the Base of the Ballhead.

When the Head Locking Knob is released,

it is possible to move the Ballhead with

some resistance or Drag. To achieve the

proper degree of Drag, mount the intended

camera or equipment onto the Ballhead.

While holding the camera/lens loosen the

Head Locking Knob until it is released.

Turn the Drag Control Knob clockwise to

increase Drag, and counter-clockwise to

decrease it.

FOR OPTIMUM RESULTS: Adjust the Drag

under the weight capacity, temperature

and conditions under which the Ballhead

will be used.

NOTE: Do not over tighten any Locking

Knobs as this could damage the Ballhead

locking mechanism.

USER NOTICE

• Do not exceed the maximum specified

load capacity (see specifications at

www.BenroUSA.com).

• Always ensure that all Ballhead locks are

tightly engaged before mounting any gear.

• Always clean and dry any Ballhead after

it has been exposed to wet, dusty, sandy

or salty conditions. Your Ballhead is not

recommended for use in salt water. If

required, clean Ballhead using a mild

soap solution applied with a soft cloth,

rinse with fresh water and dry with soft

towel. Remove any dust, dirt or sand from

all locks and all moving parts.

• Do not leave any Ballhead in the sun

for prolonged periods and avoid high

temperature exposure.

• Avoid leaving any Tripod or Monopod

unattended in areas where people could

trip over the gear and get hurt.

• Remove camera, lens, and all gear from any

Tripod or Monopod when transporting.

• For your safety, don’t let your Benro

gear come in contact with any electrical

power source.

Drag Control Knob

Base

Pan Locking Knob

Quick Release

Locking Knob

Panning

Scale Pointer

360°

Operating Instructions & User Notice

Product specificaties

Merk:	Benro
Categorie:	Statief
Model:	B1
Kleur van het product:	Zwart
Gewicht:	400 g
Hoogte:	94 mm
Gebruikershandleiding:	Ja
Maximale gewichtscapaciteit:	14 kg
Certificering:	CE
Ingebouwd spirit niveau:	Nee
Baldiameter:	36 "
Bijlage:	1/4 "
Bodemdiameter:	50 mm
Tripod head type:	bal