Benro A48FD Handleiding
Lees hieronder de π handleiding in het Nederlandse voor Benro A48FD (2 pagina's) in de categorie Statief. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Classic Series Monopods
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Speciο¬cations and design are subject
to change without notice.
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
SETUP
Head Mounting (FIGURES 1 & 2)
If your Monopod did not come with a Head,
select one of the fine Benro Ballheads or
Tilthead that match your size Monopod
and install by screwing the Head clockwise
onto the 3/8" Mounting Thread of the Top
Plate. Once it is hand tight, secure by fully
tightening the Head Locking Screw(s) (on
select models) from below.
Most Heads have a 3/8" Base Mount so your
Benro Monopod is shipped with the 3/8
Mounting Thread exposed, but if the Head
you choose uses a 1/4β20 you can attach it
by simply reversing the Mounting Screw.
To do this turn the Locking Nut counter-
clockwise (using the supplied Wrench)
until it becomes loose, and unscrew the
Mounting Screw until it can be completely
removed. Reverse the Screw, so that the
threads are in position and screw it back
into place, secure with the Locking Nut
using the wrench.
NOTE: Allow enough of the screw threads
to be available for maximum security when
the Head is mounted onto the Monopod.
Itβs recommended that at least 5 to 6
threads be exposed before locking the
Mounting Screw in place.
OPERATION
Before using your Monopod, adjust each
Leg Section to the desired height.
Make sure that the Monopod is firmly resting
on a stable surface and mount your camera
securely on the Monopod Head. Always
engage any safety locks on the Monopod
Head to prevent any accidental dismounting.
FOR BEST RESULTS: Do not raise the
Monopod higher than necessary and extend
the largest diameter Leg Sections first.
NOTE: Never carry your Monopod with
camera gear attached.
Leg Section Adjustment (FIGURES 3 & 4)
Each Leg Section can be adjusted to the
desired length by opening the Flip Lock
Lever so the Leg is free to slide in or out.
Once the desired length is achieved, snap
the Flip Lock Lever closed so that the leg
section is securely locked. Repeat this step
for each Leg Section until the Monopod is
set to the desired height.
NOTE: To prevent any accidental damage
to your gear, always remove any mounted
equipment (camera, etc.) from the Monopod
before adjusting the Leg Sections.
User Adjustments (FIGURE 5)
Flip Lock Lever tension is adjusted using the
3mm Allen Key plus the special Six-sided
Socket Wrench built into the plastic clip
which comes attached to the monopod leg.
USER NOTICE
β’ξ Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
β’ξ Always ensure that Leg and Head Locks
are tightly engaged before mounting any
gear on your Monopod.
β’ξ Always clean and dry any Monopod after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Monopod is
not recommended for use in salt water.
If required, clean Monopod using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand
from all Leg Locks, Leg Sections and all
moving parts.
β’ξ Do not leave any Monopod in the sun
for prolonged periods and avoid high
temperature exposure.
β’ξ Avoid leaving any Monopod or Tripod
unattended in areas where people could
trip over the equipment and get hurt.
β’ξ Remove camera, lens, and all gear from
the Monopod when transporting.
β’ξ For your safety, donβt let your Benro
gear come in contact with any electrical
power source.
Top Plate
Flip Lock Lever
Closed Cell Foam Grip
Wrist Strap
Rotating Pod Foot
Locking Nut
1/4-20 + 3/8
Mounting Screw
Wrench
21
Unlock Lock
3 4
3mm Allen Key
6-sided Socket
Wrench Clip
5
Operating Instructions & User Notice
Product specificaties
| Merk: | Benro |
| Categorie: | Statief |
| Model: | A48FD |
Heb je hulp nodig?
Als je hulp nodig hebt met Benro A48FD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Statief Benro
30 April 2023
28 April 2023
24 April 2023
22 April 2023
18 April 2023
3 April 2023
31 Maart 2023
27 Maart 2023
26 Maart 2023
25 Maart 2023
Handleiding Statief
- Statief Braun
- Statief Sony
- Statief Alpine
- Statief Aukey
- Statief Bresser
- Statief DJI
- Statief Dorr
- Statief Drift
- Statief Easypix
- Statief GoPro
- Statief Hama
- Statief Kodak
- Statief Kogan
- Statief Konig
- Statief Laserliner
- Statief Livoo
- Statief Neewer
- Statief Pyle
- Statief Ravelli
- Statief Revo
- Statief Rollei
- Statief Silvercrest
- Statief Sunpak
- Statief Trust
- Statief Vanguard
- Statief Velbon
- Statief Velleman
- Statief Vortex
- Statief Winegard
- Statief Barska
- Statief Miller
- Statief Celestron
- Statief Levenhuk
- Statief Kessler
- Statief Eurolite
- Statief ARRI
- Statief JOBY
- Statief Vello
- Statief Swarovski
- Statief Testo
- Statief Carson
- Statief Magnus
- Statief Manfrotto
- Statief Sachtler
- Statief Sevenoak
- Statief Zhiyun
- Statief AVerMedia
- Statief MOZA
- Statief Cullmann
- Statief Stalco
- Statief GVM
- Statief Marshall Electronics
- Statief Rode
- Statief Slik
- Statief Celly
- Statief Gitzo
- Statief Proaim
- Statief Konig & Meyer
- Statief Ultimate Support
- Statief Oben
- Statief Glide Gear
- Statief Camgear
- Statief Libec
- Statief Redrock Micro
- Statief Auray
- Statief Ulanzi
- Statief Flycam
- Statief Gravity
- Statief Sirui
- Statief Vinten
- Statief Acratech
- Statief ProMediaGear
- Statief Fidlock
- Statief Mantona
- Statief Olloclip
- Statief IFootage
- Statief SmallRig
- Statief FeiYu-Tech
- Statief FeiyuTech
- Statief Sky-Watcher
- Statief Hohem
- Statief MOVE'N SEE
- Statief On Air
- Statief Kaiser Fototechnik
- Statief Slidekamera
- Statief IOptron
- Statief FLOWCINE
- Statief SteadiCam
- Statief Fat Gecko
- Statief 3 Legged Thing
- Statief FLM
- Statief Peak Design
- Statief Easyrig
- Statief Robus
- Statief Studio Assets
- Statief Square Jellyfish
- Statief Tiltall
- Statief E-Image
Nieuwste handleidingen voor Statief
20 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024