Behringer Oscillator Module 1004 Handleiding
Behringer
Synthesizer
Oscillator Module 1004
Lees hieronder de 📖 handleiding in het Nederlandse voor Behringer Oscillator Module 1004 (2 pagina's) in de categorie Synthesizer. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Quick Start Guide
OSCILLATOR MODULE 1004
Legendary 2500 Series Dual Core VCO
Module for Eurorack
Controls
(1) COARSE FREQUENCY – Sets the frequency from 0.03 to
32 Hz in the low (LFO) range, or from 15.5 Hz to 16 kHz in
the high (audio) range, depending on the Fine frequency
knob setting.
(2) FINE FREQUENCY – Adjusts the frequency by a factor of
±1 octave, potentially halving or doubling the frequency
at either extreme.
(3) ENABLE switch – Turns the oscillator on and o.
(4) RANGE switch – Determines whether the oscillator
operates in the low (subsonic/LFO) band or the high
(audio) band.
(5) WAVEFORM switches – Engage up to 5 waveforms by
moving the relevant toggle switch to the left, or engage
the inverse waveform by moving the switch to the right.
The center position turns the waveform o. Engaging
multiple switches simultaneously produces the average of
all active waveforms.
(6) PW knob – Manually control the pulse width for the
pulse waveform.
(7) FM 2 knob – Attenuates the signal connected to the FM
2 input.
(8) PWM knob – Adjusts the modulation depth of the PMW
control input.
(9) FM 1 knob – Attenuates the signal connected to the FM
1 input.
(10) KYBD – Connect a keyboard or other external frequency
control via 3.5 mm TS cable.
(11) FM 1/2 – Connect external voltages to modulate
the frequency.
(12) PWM – Connect an external voltage to modulate the
pulse width.
(13) OUT – Send the oscillator signal to other modules via
3.5 mm TS cable.
Power Connection
The unit comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector
a tab that will align with the gap in the socket, so it cann
be inserted incorrectly. If the power supply does not hav
a keyed socket, be sure to orient pin 1 (-12 V) with the re
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back
the module. The connector has a tab that will align with
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn
the power supply.
(1)
(2)
(3)
(6)
(7)
(8)
(5)
(4)
(9)
( ) ( ) ( ) ( )10 11 12 13
V 1.0
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded plate.
Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned.
After the nal position has been established, tighten the
screws down.
Specications
Inputs
FM 1/2
Type 2 x 3.5 mm TS jacks
Impedance 50 kΩ, unbalanced
Max input level 10 V, 1 V/octave
Keyboard
Type 3.5 mm TS jack
Impedance 50 kΩ, unbalanced
Max input level 10 V, 1 V/octave
PWM
Type 3.5 mm TS jack
Impedance 50 kΩ, unbalanced
CV range ±10 V, 10% per volt
Outputs
Out
Type 2 x 3.5 mm TS jacks
Impedance 1 kΩ, unbalanced
Max output level 10 V p-p
Controls
Coarse Sets oscillator frequency (8
octave range)
Fine Oscillator ne adjustment
(±1 octave)
Range Select LFO (0.06 Hz - 16 Hz)
or audio band (31 Hz - 8
kHz)
Enable Oscillator on/o
PW Pulse width adjustment
(5% - 95%)
PWM Modulation depth
adjustment (-∞ to unity
gain)
FM 1/2 Attenuate FM inputs (-∞ to
unity gain)
Waveform switches Select up to 5 waveforms
(sine, tri, square, saw,
pulse)
Power
Power supply Eurorack
Current draw 60 mA (+12 V), 50 mA
(-12 V)
Physical
Dimensions 46 x 81 x 129 mm (1.8 x
3.2 x 5.1")
Rack units 16 HP
Weight 0.17 kg (0.37 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Product specificaties
| Merk: | Behringer |
| Categorie: | Synthesizer |
| Model: | Oscillator Module 1004 |
Heb je hulp nodig?
Als je hulp nodig hebt met Behringer Oscillator Module 1004 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Synthesizer Behringer
14 November 2024
30 September 2024
30 Juli 2024
30 Juli 2024
3 Juli 2024
5 Mei 2024
31 Maart 2024
31 Augustus 2023
31 Augustus 2023
31 Augustus 2023
Handleiding Synthesizer
- Synthesizer Casio
- Synthesizer Pioneer
- Synthesizer Yamaha
- Synthesizer AAS
- Synthesizer Arturia
- Synthesizer Boss
- Synthesizer Korg
- Synthesizer LennarDigital
- Synthesizer Native
- Synthesizer Novation
- Synthesizer Roland
- Synthesizer Suzuki
- Synthesizer Omnitronic
- Synthesizer Elektron
- Synthesizer IK Multimedia
- Synthesizer Cre8audio
- Synthesizer Moog
- Synthesizer Make Noise
- Synthesizer Erica Synths
- Synthesizer Fred's Lab
- Synthesizer GS Music
- Synthesizer Sequential
- Synthesizer Soma
- Synthesizer Majella
- Synthesizer Dreadbox
- Synthesizer Vermona
- Synthesizer Sonicware
- Synthesizer Studiologic
- Synthesizer Modal Electronics
- Synthesizer Jomox
- Synthesizer X Audio Systems
- Synthesizer Synamodec
- Synthesizer Meebleeps Machines
- Synthesizer Kodamo
- Synthesizer Flame
- Synthesizer MFB
- Synthesizer Waldorf
- Synthesizer (Recovery)
- Synthesizer Future Retro
- Synthesizer ELTA Music
Nieuwste handleidingen voor Synthesizer
2 November 2024
29 Augustus 2024
31 Juli 2024
10 Juni 2024
10 Juni 2024
10 Juni 2024
4 Mei 2024
1 Maart 2024
28 Februari 2024
28 Februari 2024