Behringer 992 Handleiding

Behringer Niet gecategoriseerd 992

Lees hieronder de 📖 handleiding in het Nederlandse voor Behringer 992 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Quick Start Guide
992 CONTROL VOLTAGES
Legendary Analog CV Routing
Module for Eurorack
Controls
(1) CV Switches – Allow the voltage or signal from the
associated input to be sent to the output jacks when the
switch is in the up position. The input is disconnected
when the switch is in the down position.
(2) EXT INPUT – Additional input to be used with the signal-
inverting attenuator circuit.
(3) Attenuator Knob - Turn clockwise to adjust the CV level
from 0 to 10 (unity gain). Turn counterclockwise to invert
the signal from 0 to -10, which is also unity gain. At the
center 0 position, the signal is o (-∞).
(4) CONTROL INPUTS – Connect control voltages from other
modules via 3.5 mm TS cable.
(5) FREQUENCY CONTROL TO LPF – Send the combined
voltage from all 4 inputs to up to 3 modules via
3.5 mm TS cable.
Power Connection
The 992 comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series ofxed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established, tighten the
screws down.
(1)
(4)
(5)
(2) (3)
Specications
Signal Connections
Control inputs 3 x 3.5 mm jacks, summed
Impedance 100 kΩ unbalanced
CV range 1 V / octave,
+/-10 V maximum
External input 1 x 3.5 mm jack,
summed with CV inputs
Impedance 100 kΩ unbalanced
Attenuation -∞ to unity gain,
inverting and non inverting
Control outputs 3 x 3.5 mm parallel jacks
Impedance 10 Ω unbalanced
Maximum output level +/-10 V
Controls
Control selectors 4 x sliding routing switches
Attenuator Rotary knob, selectable
Power
Power supply Eurorack
Current draw 10 mA (+12 V),
10 mA (-12 V)
Physical
Dimensions 35 x 40 x 129 mm
(1.4 x 1.6 x 5.1")
Rack units 8 HP
Weight 0.09 kg (0.2 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese Medicine Park,
Nanlang Town, 528451, Zhongshan City, Guangdong Province, China

Product specificaties

Merk: Behringer
Categorie: Niet gecategoriseerd
Model: 992

Heb je hulp nodig?

Als je hulp nodig hebt met Behringer 992 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Behringer

Behringer

Behringer GLC2-600 Handleiding

12 November 2024
Behringer

Behringer GMC-1000 Handleiding

12 November 2024
Behringer

Behringer GIC-1000 Handleiding

12 November 2024
Behringer

Behringer GIC-150 Handleiding

12 November 2024
Behringer

Behringer GIC-300 Handleiding

12 November 2024
Behringer

Behringer GIC-600 Handleiding

12 November 2024
Behringer

Behringer GMC-150 Handleiding

12 November 2024
Behringer

Behringer GLC2-300 Handleiding

12 November 2024
Behringer

Behringer GLC2-1000 Handleiding

12 November 2024
Behringer

Behringer RD-6-SB -Translucent Handleiding

18 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024
Kolcraft

Kolcraft MLB New York Yankees Handleiding

26 November 2024
Kolcraft

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024
Kolcraft

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024
Nedis

Nedis POCO106 Handleiding

26 November 2024
Nedis

Nedis BTSM1GY Handleiding

26 November 2024
Turbosound

Turbosound TPOLEAJ-01 Handleiding

26 November 2024
Turbosound

Turbosound TSTAND-01 Handleiding

26 November 2024
IFM

IFM TAD981 Handleiding

26 November 2024
IFM

IFM TAD961 Handleiding

26 November 2024