BeamZ S1500 160.492 Handleiding

BeamZ Effect machine S1500 160.492

Lees hieronder de 📖 handleiding in het Nederlandse voor BeamZ S1500 160.492 (17 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/17

Ref. № 160.492

S1500 DMX

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

BEDIENUNGSANLEITUNG

V1.1 Warning:

- The smokemachine must be placed at least 100 cm away from inammable materials such as

curtains, books, etc. Make sure that the housing cannot be touched by accident. - For indoor

use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the rst use, have the unit checked by a qualied person.

- The unit contains voltage carrying parts. DO NOT open the smokemachine - Never plug or unplug

the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualied technician.

- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains

outlet. It needs to be repaired by a qualified technician.

- Only connect this unit to an earthed mains outlet of 230Vac/50Hz .

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing.

Please let the unit reach room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid

chain, a steel cable, etc. which has to be fastened separately from the mounting bracket.

- The supplied bracket is the main xing and must be used to solidly mount the light eect.

- In order to avoid accidents in public premises, the local legal requirements and safety

regulations/warnings must be fullled.

- Keep out of the reach of children.

Safety

Plug the smoke machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord

can only be replaced by an original replacement, supplied by Tronios.

Be careful when filling the uid tank. First of all, unplug the mains lead! Then unscrew the cap on the tank

and ll it by means of a funnel.

Only use the original Beamz smoke uid which is environmental friendly and, if used correctly, leaves no

residues. Do not obstruct the openings on top of the case to guarantee a good ventilation. The heating

element of the smoke machine generates heat which needs to be removed. Don’t put any objects on the

smoke machine.

Installation and Use

Unpack the fog machine. Do not connect yet the net cable. Connect the remote control to the connector on

the back of the fogger. Fill the uid tank by means of a funnel. Plug the unit into a mains outlet. Thus the

heating element is automatically switched on. Depending on the room temperature, it takes about 8 minutes

until the working temperature is reached. Then the thermostat is clicking and the LED on the manual control

lights up.

Push the switch once and the smoke machine will produce a nice thick fog. Once the smoke machine has

reached its working temperature (the LED is lit) the smoke machine can produce continuously fog during

max 1 minute.

After this period of time, the fog generator is cooled so much down that the thermostat switches o. Wait a

few minutes until the working temperature is reached again. It is recommended to produce smoke with small

pauses in between so that the temperature is maintained and the thermostat doesn’t switch off.

Location

Select a location where it is easy to ll the tank. It is also possible to hang the unit by means of the supplied

holder and xing screws.

Switching the unit o

Switch the unit o by unplugging it from the mains. Otherwise the 1500W heating element will draw

unnecessarily current.

Timer remote control

Connect the remote control to the connector on the back of the fogger.

After some warm-up time, the device is ready for use, the LED will light up on the remote. During use, it

may happen that the machine stops, in this case the LED will go out, indicating that the machine is warming

up. Timer function:

Press the yellow button and set the interval, duration and volume controls to the desired level.

Interval: time between the smoke moments (10- econds) 200 s

Volume: amount of smoke (0-

100%) Duration: duration of the

smoking time Continuous

function:

Press the red button and set the volume to the desired level. The machine will continueously produce an

amount of smoke. It may be that the machine in between have to warm up, during this period no smoke is

produced. How many times this is done depends on the amount of smoke.

Manual Mode:

Press the green button to produce 100% smoke immediately; this button overrides all previous settings.

DMX control

Connect the device directly to a DMX controller or a DMX loop with multiple DMX effects. The machine has

a 3-pin XLR connector for DMX connection.

Address Setup:

Use the DIP switch on the rear panel to set the start address. The base/start address is dened as a rst

channel, where responsive to the device. Check if no overlapping channels are used! Example addressing:

DMX address

DIP on

Value for DIP switch

Diagram

DIP 4

DIP 2

2 (8+2 = 10)

DIP 5

DIP 4

8 (16+8 = 24)

Product specificaties

Merk:	BeamZ
Categorie:	Effect machine
Model:	S1500 160.492
Kleur van het product:	Black, Grey
Gewicht:	5600 g
Snoerlengte:	3 m
Vermogen:	1500 W
Afstandsbediening:	Bedraad
Op afstand bedienbaar:	Ja
Opwarmtijd:	8 min
Productafmetingen (B x H x D):	470 x 250 x 190 mm
AC-ingangsspanning:	220-240 V
AC-ingangsfrequentie:	50 Hz
Vloeistoftank capaciteit:	2 l
Hoeveelheid rook uitstoot:	295 m³/min
Bedrijfsvloeistof:	Water