Bauknecht GSUK 61102 Di A+ WS Handleiding

Bauknecht Vaatwassers GSUK 61102 Di A+ WS

Lees hieronder de 📖 handleiding in het Nederlandse voor Bauknecht GSUK 61102 Di A+ WS (8 pagina's) in de categorie Vaatwassers. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

GB -1-

-1-

-1--1-

Chart

CANCEL/OFF BU

CANCEL/OFF BUCANCEL/OFF BUTTON

TTON

TTONTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

PROGRAM SELE

PROGRAM SELEPROGRAM SELECTION

CTION

CTION CTION

BUTTON

BUTTONBUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below

STSTART/RESUME BUTTON

ART/RESUME BUTTON

ART/RESUME BUTTONART/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle close the door and

push Start button again.

(see at right for options descripti

(see at right for options descripti(see at right for options description)

on)

on)on)

1)1) Program data obtained in conformi

Program data obtained in conformi

Program data obtained in conformiProgram data obtained in conformity with

ty with

ty withty with European standar

European standar

European standar European standard EN 50242, o

d EN 50242, o

d EN 50242, od EN 50242, obtained und

btained und

btained undbtained under normal conditions

er normal conditions

er normal conditions er normal conditions (without additional

(without additional

(without additional (without additional

options) and may vary depe

options) and may vary depeoptions) and may vary depending on conditions

nding on conditions

nding on conditionsnding on conditions. Differences of up to

. Differences of up to

. Differences of up to. Differences of up to 20 minutes are possible wi

20 minutes are possible wi

20 minutes are possible wi 20 minutes are possible with sensor progra

th sensor progra

th sensor prograth sensor programs as a result of

ms as a result of

ms as a result ofms as a result of the

the

the the

appliance’s automatic

appliance’s automatic appliance’s automatic calibration system.

calibration system.

calibration system.calibration system.

2)2) Reference program for energy label in compliance with EN 5

Reference program for energy label in compliance with EN 5

Reference program for energy label in compliance with EN 5Reference program for energy label in compliance with EN 50242

0242

02420242 regulations. - Note for T

regulations. - Note for T

regulations. - Note for T regulations. - Note for T

esting Institutes: for detailed infor

esting Institutes: for detailed inforesting Institutes: for detailed information

mation

mation mation

on the EN/Standard loading com

on the EN/Standard loading comon the EN/Standard loading comparison test and other tests,

parison test and other tests,

parison test and other tests,parison test and other tests, conta

conta

conta contact the follow

ct the follow

ct the followct the following address: “nk

ing address: “nk

ing address: “nking address: “nk_customer@whi

_customer@whi

_customer@whi_customer@whirlpool.com

rlpool.com

rlpool.comrlpool.com”.

”.

”.”.

3)3) The antibacterial action ha

The antibacterial action ha

The antibacterial action haThe antibacterial action has been tested by the Institut Past

s been tested by the Institut Past

s been tested by the Institut Pasts been tested by the Institut Pasteur of Lille (France), based on the NF EN 13

eur of Lille (France), based on the NF EN 13

eur of Lille (France), based on the NF EN 13eur of Lille (France), based on the NF EN 13697 standard of

697 standard of

697 standard of 697 standard of

November 2001.

November 2001.November 2001.

TTable of programs

able of programs

able of programsable of programs

Deter-

Deter-Deter-

gent

gentgent

Consumption

ConsumptionConsumption

Drying

DryingDrying

Phase

PhasePhase

Programs

ProgramsPrograms Available

Available

AvailableAvailable

options

optionsoptions Loading instructions

Loading instructions

Loading instructionsLoading instructions

Litres

LitresLitres kWh

kWh

kWhkWh Minutes

Minutes

MinutesMinutes 1)

1)1)

P1P1

Sensor

SensorSensor 40°-70°C

40°-70°C

40°-70°C40°-70°C Delay

Antibacterial

rinse

Recommended program for

routine washes, with dried-on

food (e.g. EN 50242)

X 7-14 1.00-1.60 70-155 Full

P2P2

Pre

PrePre-W

-W

-W-Was

asash

hh cold

cold

coldcold Delay Crockery to be washed later. — 4.0 0.03 14 NO

P3P3

Rap

RapRapi

iid

dd 45°C

45°C

45°C45°C Delay Lightly soiled crockery, with

no dried-on food. X 11.0 0.80 30 NO

P4P4 Eco

Eco

EcoEco 2)

2)2) 50°C

50°C

50°C50°C Delay

Antibacterial

rinse

Normally soiled crockery.

Energy-saving program. X 12.0 1.03 170 Full

P5P5

Fast Daily

Fast DailyFast Daily 60°C

60°C

60°C60°C Delay

Antibacterial

rinse Normally soiled crockery. X 10.0 1.30 80 Full

P6P6 Steam

Steam

SteamSteam Delay

Antibacterial

rinse

Program including steam

action dedicated for heavily

soiled crockery, pots and pans.

Soaking or hand pretreatment

is no longer needed.

X 14.0 1.70 180 Full

5019 496 01738

5019 496 017385019 496 01738

Options and display description

SAL

SALSALT INDICA

T INDICA

T INDICAT INDICATOR

TOR

TORTOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

ANTIBACTERIAL RINS

ANTIBACTERIAL RINSANTIBACTERIAL RINSE

This function activates an antibacterial rinse at the end of

the wash cycle, guaranteeing a further reduction of

bacteria. Press the button to activate or deactivate the

function. This function can be used with the programs

indicated in the table of programs. The dishwasher door

must be kept shut for the entire duration of the program

in order to guarantee reduction of bacteria. If the door is

opened the indicator lamp starts flashing.

TTABLET SETTING

ABLET SETTING

ABLET SETTINGABLET SETTING

This setting allows to optimize

the cycle performances

according the type of

detergent used.

Push the Tablet button for

3 seconds (until the indicator

lights up) if you are using the

combined detergents in tablet

(rinse aid, salt and detergent in

1 dose).

If you are using powder

detergent or liquid detergent,

the Tablet indicator on the

control panel has to be off.

DELA

DELADELAYED ST

YED ST

YED STYED START BUTTON

ART BUTTON

ART BUTTONART BUTTON

Push the button (repeatedly) to delay

the start of the program - delay

indicator turns on. Adjustable from

1 to 24 hours.

With each press of the button, the

delay increases by one hour and after

"h 24" returns to "h 00”. When this

option is selected the delay indicator

turns on. Then press the START

button. The dishwasher will start after

the set time.

RINSE AID INDICATOR

RINSE AID INDICATORRINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

WASH TIME DISPLAY

WASH TIME DISPLAYWASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULL

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLBEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULL

Y READ

Y READ Y READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBL

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLTHIS QUICK REFERENCE GUIDE AND THE ASSEMBL

Y INSTRUCTIONS!

Y INSTRUCTIONS!Y INSTRUCTIONS!

THE CONTROL P

THE CONTROL PTHE CONTROL PANEL OF THIS DISHW

ANEL OF THIS DISHW

ANEL OF THIS DISHWANEL OF THIS DISHWASHER ACTIV

ASHER ACTIV

ASHER ACTIVASHER ACTIVA

AATES PUSHING

TES PUSHING

TES PUSHING TES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

ANY BUTTON EXCEPT CANCEL/OFF BUTTON. ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SA

FOR ENERGY SAFOR ENERGY SAVING THE CONTROL PANEL DEA

VING THE CONTROL PANEL DEA

VING THE CONTROL PANEL DEAVING THE CONTROL PANEL DEACTIV

CTIV

CTIVCTIVA

AATES

TES

TES TES

AUTOMA

AUTOMAAUTOMATICALL

TICALL

TICALLTICALLY AFTER 30 SECONDS IF NO CY

Y AFTER 30 SECONDS IF NO CY

Y AFTER 30 SECONDS IF NO CYY AFTER 30 SECONDS IF NO CYCLE HAS ST

CLE HAS ST

CLE HAS STCLE HAS STARTED.

ARTED.

ARTED.ARTED.

Quick reference guide

Quick reference guideQuick reference guide

Bauknecht is a registered trademark

Bauknecht is a registered trademarkBauknecht is a registered trademark

GB -2-

-2-

-2--2-

First time use

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

WWater hardness should be set only

ater hardness should be set only

ater hardness should be set only ater hardness should be set only

before the first wash or if water

before the first wash or if water before the first wash or if water

hardness has been changed

hardness has been changedhardness has been changed

(depending on the model)

The salt level indicator lamp may remain lit

at the end of several wash cycles. If the

water hardness level falls within category

(soft), no salt is required.

Salt indica

Salt indicaSalt indicator on the con

tor on the con

tor on the contor on the control panel

trol panel

trol paneltrol panel Salt indicator on the s

Salt indicator on the s

Salt indicator on the sSalt indicator on the salt reservoir cap

alt reservoir cap

alt reservoir capalt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED. green: OK. clear: NEEDS TO

BE ADDED

- Press and hold together PROGRAM Selection

PROGRAM Selection

PROGRAM Selection PROGRAM Selection and CANCEL/Off

CANCEL/Off

CANCEL/OffCANCEL/Off buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the PROGRAM S

PROGRAM S

PROGRAM SPROGRAM Selection

election

electionelection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the

next press of the start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/Re

Start/Re

Start/ReStart/Resume

sume

sumesume button to save setting.

1.1. 2.

2.2.Ask your water supply company what the water hardness

water hardness

water hardnesswater hardness is... ...enter this value on

your dishwasher Suggestions for detergent use

German

degrees °dH French

degrees °fH English

degrees °eH Water hardness

level Insert value is shown

in the display Gel or Powder

(rinse aid and salt) Tablets

0 - 5 0 - 9 0 - 6.3 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 if water is

HARD extra salt

needs to be added

(go to step 1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Water hardness level is factory

set for medium-hard water

(level 4).

Even if you use tablets which

include salt functionality, you

must still add regeneration salt

since such detergents are not

effective enough at softening

hard water.

At first time use, the salt

At first time use, the salt At first time use, the salt

reservoir has to be fille

reservoir has to be fillereservoir has to be filled

d d

independently from water

independently from water independently from water

hardness level

hardness level hardness level (see description

below in step 1 “Daily check”).

1Visual indicator

(depending

on the model).

Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

Daily check

Filling the salt reservoir -

Filling the salt reservoir - Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Add salt

Add salt Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

Once regeneration salt is added, immediately

immediately

immediatelyimmediately start a wash program (the “Pre-wash” program alone is not

not

notnot sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

How to set water hardness in order to always assure the best cleaning resultsHow to set water hardness in order to always assure the best cleaning results

GB -3-

-3-

-3--3-

Daily check

Check the rinse aid indicator to check the level

into the dispenser.

(depending on the model)

Rinse aid indicator on the control panel

Rinse aid indicator on the control panelRinse aid indicator on the control panel Rinse aid indicator on th

Rinse aid indicator on th

Rinse aid indicator on thRinse aid indicator on the dispenser

e dispenser

e dispensere dispenser

The indicator lamp lights up when RINSE AID NEEDS

TO BE ADDED. dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immedia

Immedia

ImmediaImmediately

tely

telytely wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the

appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty

drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with

rinse aid incorporated tend to form excess suds.

Daily use

Adding detergent -

Adding detergent - Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the

detergent dispenser

prior to starting a

wash program.

Shut the cover

by pressing dedicated ribs.