Bauknecht GSIK 6518/1 WS Handleiding

Bauknecht Vaatwassers GSIK 6518/1 WS

Lees hieronder de 📖 handleiding in het Nederlandse voor Bauknecht GSIK 6518/1 WS (8 pagina's) in de categorie Vaatwassers. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

GB -1-

Chart

START

DELAY

option

ON/OFF

BUTTON

PROGRAM

SELECTOR

KNOB

(see “Table of

programs”

below).

START BUTTON

The indicator lights up during operation, flashes when a fault occurs, and goes off

at the end of the program.

START BUTTON RESET FUNCTION:

Press this button for at least 2 seconds; the selected program and options will be

cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be

cancelled by RESETTING. Detailed instructions are given in chapter “What to do if...”.

(see at right for options description)

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions

(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible

with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for

detailed information on the EN/Standard loading comparison test and other tests, contact the following address:

“nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697

standard of November 2001.

Table of programs

Deter-

gent

Consumption

PPrograms Available

options Loading instructions Litres kWh Minutes 1)

1Quickwash 45°C Delay

Lightly soiled crockery, with no dried-

on food.

* Use of tablets not

recommended.

X *11.0 0.80 30

2Bio Normal 2) 50°C Delay Normally soiled crockery.

Energy-saving program. X 12.0 1.05 165

3Intensive 70°C Delay

Recommended program for heavily

soiled crockery, especially suitable for

pots and pans.

X 14.0 1.55 155

4Hygienic + 3) Delay

Normally or heavily soiled crockery,

with additional antibacterial wash.

Program interruption (e.g. due to door

opening) can compromise elimination

of germs.

X 13.0 1.50 115

5Half Load 50°C Delay Ideal for washing a half load of lightly

or normally soiled crockery. X 10.0 1.04 145

5019 496 01672GSIK 6518

DELAYED START

BUTTON

Press the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press of

the button, the delayed

start indicator increases by

one hour and after 24

restarts from 00. Then

press the START button.

The dishwasher will start

after the set time.

RINSE AID INDICATOR

When lit, the rinse aid dispenser

needs to be refilled.

SALT INDICATOR

When lit, the salt reservoir

needs to be refilled.

FAULT INDICATION AND WASH TIME DISPLAY

In normal operation it indicates the remaining time

(h:mm), whereas with “Delayed start” selected it

indicates the time remaining until program start (hh).

If “F..” appears on the display, see chapter “What to do if...”.

Options and display description

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE ASSEMBLY

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

Quick reference guide

GB -2-

First time use

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

In order to always ensure the best cleaning

results, you NEED to set:

DETERGENT type and WATER HARDNESS.

1. Select 3rd program (see

Table of programs - page 1)

2. Press START button

for 7 seconds

3a. Check your

detergent type...

3b....and set it on your dishwasher

using the START button

(as per table below)

4. Remember to use salt and rinse

aid when needed (as indicated

below)

5. Switch off and switch on

again to save setting

Detergent

types

Dishwasher models

model without

display model with display

Powder or gel

(factory setting) no symbol add salt add rinse aid

Tablet 2 in 1 add salt

Tablet 3 in 1

Tablet All in 1

For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.

3h 6h 9h

rinse aid

salt rinse aid

How to set water hardness

* only before the first wash or if

the water hardness has been

changed

Switch on the appliance

- Select the 2nd program “P2” - consult the table of programs.

- Press the START button for at least 5 seconds until the START indicator lamp flashes.

- The water hardness setting is shown on the display (if present) or the START button flashes.

- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.

- The appliance must be switched off to memorise the new setting.

Water hardness level is factory set for

medium hard water (a number “4” is

shown on the display or the START

indicator lamp flashes 4 times).

Even if you use tablets which include salt

functionality, you must still add salt since

such detergents are not effective enough

at softening hard water.

At first time use, the salt reservoir has to

be filled independently from water

hardness level (see description in step 1

“Daily check”).

1. Ask your water supply company what the water hardness is... 2. ...enter this value on your

dishwasher

Suggestions for detergent use

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water

hardness

Dishwasher

with display:

insert value in

the display

Dishwasher

without

display: count

START button

led flashes

Gel or Powder

(rinse aid and

salt)

Table ts

0 - 5 0 - 9 0 - 6.3 Soft 1 1x

go to step 1

(see “Daily

check”)

if extra salt is

needed go to

step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2 2x

11 - 15 19 - 27 13.3 - 18.9 Average 3 3x

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 4x

22 - 28 38 - 50 26.6 - 35 Hard 5 5x

29 - 35 51 - 63 35.7 - 44.1 Very hard 6 6x

36 - 50 64 - 90 44.8 - 62.4 Extremely

hard 7 7x

How to set detergent type: powder/gel/tablet (if option is available)

GB -3-

Daily check

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Visual indicator

(depending

on model).

Unscrew cap.

Fill the salt reservoir

with water before the

first wash only.

Add salt

(never add detergent!).

min. 0.8 kg

max. 1 kg

Screw on the cap. Salt residual

around the cap need to be

removed. Some salt reservoir have

a level indicator integrated in the

cap (see below how to check).

If required,

open the cover

B (press the

dedicated

button).

Open the cover A

(press the dedicated

button).

Only fill the

detergent dispenser

prior to starting a

wash program.

Shut the cover

by pressing

dedicated ribs.

Insert detergent: Tablet / powder / liquid into the big chamber

Add rinse aid

to the max.

line ~150 ml

The rinse aid dosage can be adjusted to the

detergent used. The lower the setting, the less

rinse aid is dispensed (factory setting: position

4). Press the button to open the cover B. Using

a coin or similar object, turn the arrow to the

desired setting. After adjusting the rinse aid

setting, shut the cover again.

Visual

indicator

Use only one tablet per one

cycle, only placed in detergent

dispenser.

All types of tablets can be

used, but for 2 in 1 type

adding of salt is mandatory.

Check the rinse aid indicator to check the level into the

dispenser.

(depending on the model)

Rinse aid indicator on the control panel Rinse aid indicator on the dispenser

The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED. dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid

setting will not improve the situation. Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents

with rinse aid incorporated tend to form excess suds.

(depending on the model)