Barska AX12840 Handleiding

Barska Kluis AX12840

Lees hieronder de 📖 handleiding in het Nederlandse voor Barska AX12840 (2 pagina's) in de categorie Kluis. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Getting Started

1. Remove safe from packaging and remove Manual and

all accessories that came with the safe.

2. Insert emergency key into key access, and turn

clockwise to unlock and open the safe.

3. Unscrew battery compartment and insert 4 AA

batteries. (Bolts are extended). Do not mix old and

new batteries.

4. Place any fingerprint on scanner. Few beeps will be

heard and red flashes will be seen, then bolts will

retract, the safe will open.

Note: If safe opens with few beeps and red flashes, this

means safe is in factory default mode: ANY Fingerprint

can open the safe.

Fingerprint Registration

1. With safe open and bolts retracted, press and release

initialization button located inside the safe and place

desired finger on fingerprint scanner.

Successful Registration

2 beeps will be heard and 2 green flashes will be seen.

Unsuccessful Registration

2 quick beeps will be heard along with red flash.

Test Registered Fingerprint

1. With safe door open, press “0” on keypad to extend

the bolts, the safe is locked.

2. Press “0” to wake up safe and place Registered

Fingerprint on the scanner. If safe bolts retract and 2

beeps and green flash is seen, it means the

registration was successful. If safe opens with several

beeps and red flash is seen then registration was

unsuccessful. Follow steps under Fingerprint

Registration to register safe.

Pin Code Registration

1. Enter Current Pin Code (Default Pin Code:

“12312312312”) then immediately press “3” on keypad,

both red and green light should be seen.

2. Enter new desired Pin Code 4 – 11 digits. If less than

11 digits, press initialization button on the back of the

safe to finish. 1 long beep will be heard and green light

will be seen.

Note: Pin Code CANNOT start with “0”

See reverse side for more information 8/15

BC443

WARNING

Test Registered Pin Code

1. With safe door open, press “0” on keypad to extend

the bolts, the safe is locked.

2 Enter Registered Pin Code. If there are beeps and

green light flashes, bolts retract then registration was

successful. If there are two short beeps and red light

flashes, bolts do NOT retract then registration was

unsuccessful. Follow steps under Pin Code

Registration to register desired Pin Code.

Close / Open Safe Door

Open Safe Door with Fingerprint

Press “0” on keypad to wake up the safe and place

Registered Finger on the scanner. Safe should open.

Open Safe Door with Pin Code

Enter Registered Pin Code and safe should open.

Closing Safe Door

Please push door against the body of the safe and press

“0” on keypad. Bolts should extend and Safe door is now

locked.

Silent Mode

Sound Off

Press and hold initialization button until 1 beep is

heard along with green flash. Sound is now disabled.

Note: Door Open Alarm will not beep when safe is in

silent mode, but green light will flash once every

4 seconds.

Sound On

Press and hold initialization button until 1 beep is

heard along with green flash.

Door Open Alarm

Safe will start beeping 1 min after safe door has been

opened. Please close safe door or turn safe to silent

mode to turn off alarm.

* Actual model may vary

A. Initialization Button

B. Battery Compartment

C. Bolts

D. Fingerprint Scanner

User’s Manual for Biometric Keypad Safe

Read all instructions before using this safe

- Safe can be opened by either Fingerprint, PIN code,

and/or Emergency Keys.

- If user resets the safe to Factory Default mode: ANY

fingerprint and Factory Default PIN code can open

the safe.

- If safe is in factory default mode Red flash will be seen

along with several beeps when accessing the safe.

- Register BOTH Fingerprint and PIN code to disable

factory default mode.

- Register at least two different fingerprints and test a few

times before closing the safe door.

- Test with a non-registered fingerprint. If the safe opens,

the safe is still in Factory Default mode.

- Avoid leaving safe door open and unattended; it will allow

unauthorized individuals to add their fingerprints and/or

reprogram the safe, gaining full access to the safe and

the contents.

- Test the Emergency Keys and store them in a secure

place, NOT inside of the safe.

- To maximize the security and performance of the safe,

test registered fingerprints every 6 months.

E. Indicator Lights

F. Emergency Key Access

G. Key Pad

Resetting the Safe

Take all the batteries out of the safe, press and hold

the initialization button inside the safe while

re-inserting the batteries, keep holding initialization

button until 3 beeps are heard and green flash is seen.

Test Safe to See if it is Reset

With Fingerprint Press “0” on keypad and place any

fingerprint on fingerprint scanner. Few beeps will be

heard and red flashes will be seen, then bolts will

retract, the safe will open.

With Pin Code Press “12312312312” on keypad, beep

will be heard and green flash will be seen, the bolts

will retract and safe should open.

Low Battery Warning

An alarm sound and red flash will be seen when trying to

access safe. Safe may allow access still, but batteries should

be replaced as soon as possible.

Note: Can use 9v battery as an external power source. Place

9v battery under fingerprint module, touching the metal

contacts under the fingerprint module. Safe should power up,

if not switch the polarity of the 9v battery.

Care and Maintenance

- To maximize the security and performance of the safe, keep

Fingerprint Scanner clean; use a dry cloth to remove any

smudges or prints off the Fingerprint Scanner after

each use.

- Test registered fingerprints and PIN code every 6 months.

- Keep liquids away from the control panel. Spills on the

control panel will cause damage and possibly electric shock.

- Secure safe in a proper area to prevent from falling and

causing damage or injury.

- DO NOT disassemble the product. For all repairs, contact

BARSKA Customer Service.

- DO NOT use chemicals or cleaning agents to clean

the safe.

User’s Manual for Biometric Keypad Safe

Read all instructions before using this safe

Mounting Instructions

The safe may be mounted to a wall or floor. Be aware of

the load bearing. Failure to do so can result in personal

injury and/or damage to property. Use appropriate tools

when performing work and always use eye protection.

Wall Mounting

Do not mount the safe without anchoring to the wall.

- Find the studs in the wall, at your desired location. Most

studs are 16 inches or 24 inches apart.

- Check the wall for concealed wires or pipes.

- Measure the location of the pre-set drill holes; mark

their exact position onto the wall ensuring that the

studs or anything else behind will not interfere.

- Drill the appropriate size holes for the anchors you

are using.

- Carefully press the anchor into the holes at this time.

- Mount the safe by running screws from inside of the

safe and securing to anchors; ensure the safe is

mounted securely.

Floor Mounting

- Use proper drill tools depending on the type of floor you

are mounting the safe (wood, tile, or concrete).

- Measure the location of the pre-set drill holes; mark

their exact position onto the floor.

- Drill the appropriate size holes for the anchors you

are using.

- Carefully press the anchor into the holes at this time.

- Mount the safe by running screws from inside of the

safe and securing to anchors; ensure the safe is

mounted securely.

Biometric Keypad Safe

1 YEAR LIMITED WARRANTY

BARSKA warrants this new safe to be free of original defects in

material and/or workmanship under normal use for a period of twelve

(12) months from the date product is received by purchaser. This

warranty does not include damage caused by improper installation or

maintenance. Damage from misuse, abuse, accident (such as

dropping), normal wear and tear, fire, flood, or acts of nature. Damage

from service or repairs other than those performed by BARSKA.

Labor, cost and shipping charges for the removal and replacement of

defective parts beyond the initial twelve-month warranty period. All

transportation and shipping charges. Removing or altering the seal

under any circumstances will automatically void the warranty.

This warranty is limited to original purchaser and is not transferable.

This warranty applies only to products purchased in the United States.

Please email info@barska.com or call 1.888.666.6769 for Return

Merchandise Number (RMA#) before any returns. The RMA number

must appear on the outside of the shipping package. Product must be

packed carefully and sturdily in its original packaging to prevent

damage in transit and returned freight pre-paid to:

BARSKA OPTICS

Repair Department

855 Towne Center Drive

Pomona, CA 91767

Please include all of the following when returning BARSKA products

for service and/or replacement:

1. Please write your complete details (Name, Address, Telephone #,

E-mail address, RMA#, etc.)

2. Purchase receipt or Proof of Purchase. (Original/Copy)

3. A brief explanation of the defect.

4. A Check/Money Order of cover inspection, shipping and handling.

Charges are as follows:

Biometric Keypad Safe BDK100 - $40.00

Biometric Keypad Safe BDK200 - $40.00

Biometric Keypad Safe BDK300 - $60.00

Biometric Keypad Safe BDK400 - $60.00

*Please allow 6-8 weeks for delivery.

BARSKA will examine and test returned product and repair or replace

defective part(s) or units with new part(s) or a new unit if necessary

within the warranty period. Purchaser is required to remit $40.00 to

BARSKA for return shipping and handling at time product is returned.

If repair is required after warranty period expiration, purchaser will be

charged for replacement parts and return shipping.

BARSKA® Optics shall not be liable for any consequential, incidental

and/or contingent damages whatsoever. We will not pay shipping,

insurance or transportation charges from you to us, or any import

fees, duties and or taxes. This warranty supersedes all previous

BARSKA® Optics warranties.

855 Towne Center Drive | Pomona, CA 91767

(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com

Product specificaties

Merk:	Barska
Categorie:	Kluis
Model:	AX12840
Gewicht:	11340 g
Soort:	Vrijstaande kluis
Type stroombron:	Batterij/Accu
Met slot:	Ja
Materiaal:	Staal
Inhoud:	- l
Slot type:	Electronic, Fingerprint reader, Round key