Barska AX11650 Handleiding

Barska Kluis AX11650

Lees hieronder de 📖 handleiding in het Nederlandse voor Barska AX11650 (2 pagina's) in de categorie Kluis. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

See reverse side for more information

3/13

BC282

User’s Manual for Biometric Safe

GETTING STARTED

1. Remove Emergency Keys from accessory package

2. To expose the Emergency Key access, remove Logo Plate

(G) screws with provided tool

3. Insert Emergency Key into key access, push and turn

counter-clockwise

4. Turn Handle (H) clockwise to open the safe

5. Continue with INSTALL BATTERIES

INSTALL BATTERIES

1. Remove Battery Compartment (B) cover

2. Insert 4 AA batteries and restore battery cover

3. Continue with FINGERPRITN REGISTRATION

FINGERPRINT REGISTRATION

IMPORTANT: The safe is in either Pre-registered mode or

Factory Default mode, test safe to determine factory settings

below

Pre-registered mode: Safe can NOT be opened with any

fingerprint(s)

Factory Default mode: Safe can be opened with ANY

fingerprint(s)

1. With the safe door open, press and release Initialization

Button (A)

2. Immediately place a finger on the Fingerprint Scanner (D)

- Hold finger still

- 1 beep will be heard recognizing the fingerprint; followed by

2 consecutive beeps

- Remove finger

- Registration is complete

Successful Registration

Registration is successful when a total of 3 beeps are heard

Unsuccessful Registration

2 short beeps will be heard; repeat registration process again

3. To register another fingerprint - repeat steps 1 – 2

4. Continue with TEST (NON) REGISTERED FINGERPRINTS

TEST (NON) REGISTERED FINGERPRINTS

1. Test multiple Non-Registered fingerprints

- Close safe door, turn Handle (H) counter-clockwise to

lock the safe

- Press and release Wake-Up Button (F)

- Place a non-registered finger on the Fingerprint Scanner (D)

- Turn Handle (H) clockwise, the door should not open

- If the door opens with a non-registered fingerprint,

registration was unsuccessful; the safe is still in Factory

Default mode

- Repeat steps under FINGERPRINT REGISTRATION, and

test multiple non-registered fingerprints

2. Test a Registered fingerprint

- With door closed, press and release Wake-Up Button (F)

- Place a registered finger on the Fingerprint Scanner (D)

- Turn Handle (H) clockwise, the door should open

- Registration was successful, if it only opened with registered

fingerprint(s)

CLOSE/OPEN SAFE DOOR

CLOSE: Close safe door, turn Handle (H) counter-clockwise to

lock the safe

OPEN: Press and release Wake-Up Button (F)

- Place a registered finger on Fingerprint Scanner (D)

- Turn Handle (H) clockwise to open the safe

WARNING

- New Safe is in either Pre-registered mode or Factory

Default mode; ANY fingerprint can open the safe. Only

a successfully registered Fingerprint(s) can terminate

Factory Default mode.

- Register at least two different fingerprints and test a

few times before closing the safe door.

- Test with a non-registered fingerprint. If the safe

opens, the safe is still in Factory Default mode.

- Avoid leaving safe door open and unattended; it will

allow unauthorized individuals to add their fingerprints

and/or reprogram the safe, gaining full access to the

safe and the contents.

- Test the Emergency Keys and store them in a secure

place, NOT inside of the safe.

- To maximize the security and performance of the

safe, test registered fingerprints every 6 months.

- Initialization button cover must be restored after

every use.

- If user resets the safe to Factory Default mode: ANY

fingerprint can open the safe.

- Test and make sure the safe works properly

before mounting.

- Mount the safe before use because the safe has a

small base with a heavy door, and will tip forward if not

properly mounted.

- Keep children away from safe; they should not play

with or around the safe at anytime. Children at play

could accidentally get locked inside the safe or

accidentally pull on the safe door causing safe to tip

over if not properly mounted.

- Failure to follow these warnings could result in serious

injury or death.

Read all instructions before using this safe.

* Actual model may vary

A. Initialization Button

B. Battery Compartment

C. Bolts

D. Fingerprint Scanner

E. Indicator Lights

F. Wake-Up Button

G. Logo Plate and Emergency

Key Access

H. Handle

I. External Battery Pack

(batteries not included)

J. External Battery Access

BEEP SOUND OPTIONS

Beep OFF: Press and HOLD the Initialization Button (A) (20 -

30 seconds) until the Indicator Lights (E) flash green once

- RELEASE the Initialization Button

Beep ON: Press and HOLD the Initialization Button (A) (20 -

30 seconds) until the Indicator Lights (E) flash green, followed

by 1 beep

- RELEASE the Initialization Button

OPEN SAFE WITH EMERGENCY KEY

1. To expose the Emergency Key access, remove Logo

Plate (G) screws with provided tool

2. Insert Emergency Key into key access, push and turn key

counter-clockwise, and turn Handle (H) clockwise to open

the safe

NOTE: Store Emergency Keys in a secure place, NOT inside

of the safe

OPEN SAFE WITH EXTERNAL BATTERY PACK

Use this option when internal batteries are low

1. Insert 4 AA batteries into External Battery Pack (I)

2. Plug into External Battery Access (J)

3. Press and release Wake-Up Button (F)

- Place a registered finger on Fingerprint Scanner (D)

- Turn Handle (H) clockwise to open the safe

DELETE ALL STORED FINGERPRINTS / RESET TO

FACTORY DEFAULT MODE

1. Open safe, remove Battery Compartment (B) cover and

all 4 AA batteries

2. Press and release Wake-Up Button (F) a few times until no

beeps are heard

3. Press and HOLD the Initialization Button (A)

- Re-insert batteries; on the 4th battery you will hear 1

beep, followed by 2 consecutive beeps indicating safe is

in Factory Default mode

4. RELEASE Initialization Button (A)

5. Repeat steps 1-3 if a total of 3 beeps are not heard

6. Restore Battery Compartment (B) cover

7. All fingerprints stored in the safe have been deleted

NOTE: The safe is in Factory Default mode, ANY fingerprint

can open the safe

8. Continue with FINGERPRINT REGISTRATION and TEST

(NON) REGISTERED FINGERPRINTS

LOW BATTERY WARNING

1. When the door is closed and 3 repetitive beeps are heard,

and Indicator Lights (E) flash red, it indicates the batteries

are low

2. Replace batteries immediately

- Open safe, remove Battery Compartment (B) cover and

all 4 AA batteries

- Insert 4 new AA batteries and restore Battery

Compartment (B) cover

NOTE: All registered fingerprints remain stored

CARE AND MAINTENANCE

- To maximize the security and performance of the safe, keep

Fingerprint Scanner (D) clean; use a dry cloth to remove

any smudges or prints off the Fingerprint Scanner after

each use

- Test registered fingerprints every 6 months

- Keep liquids away from the control panel. Spills on the

control panel will cause damage and possibly electric shock

- Secure safe in a proper area to prevent from falling and

causing damage or injury

- DO NOT disassemble the product. For all repairs, contact

BARSKA Customer Service

- DO NOT use chemicals or cleaning agents to clean the safe

MOUNTING INSTRUCTIONS

The safe must be mounted to a wall or floor. Be aware of the

load bearing. Failure to do so can result in personal injury and/or

damage to property. Use appropriate

tools when performing work and always

use eye protection

Wall Mounting

Do not mount the safe without anchoring

to the wall

- Find the studs in the wall, at your

desired location. Most studs

are 16 inches or 24 inches apart

- Check the wall for concealed wires

or pipes

Mounting Holes

* Actual model may vary

- Measure the location of the pre-set drill holes; mark their exact

position onto the wall ensuring that the studs or anything else

behind will not interfere

- Drill the appropriate size holes for the anchors you are using

- Carefully press the anchor into the holes at this time

- Mount the safe by running screws from inside of the safe

and securing to anchors; ensure the safe is mounted securely

Floor Mounting

- Use proper drill tools depending on the type of floor you are

mounting the safe (wood, tile, or concrete)

- Measure the location of the pre-set drill holes; mark their

exact position onto the floor

- Drill the appropriate size holes for the anchors you are using

- Carefully press the anchor into the holes at this time

- Mount the safe by running screws from inside of the safe

and securing to anchors; ensure the safe is mounted securely

Product specificaties

Merk:	Barska
Categorie:	Kluis
Model:	AX11650
Kleur van het product:	Zwart
Gewicht:	21999 g
Breedte:	355.6 mm
Diepte:	330.2 mm
Hoogte:	501.65 mm
Soort:	Vrijstaande kluis
Montage gereedschap:	Ja
Type stroombron:	Batterij/Accu
Materiaal:	Staal
Afmetingen binnenkant (B x D x H):	343 x 241.3 x 495.3 mm
Slot type:	Fingerprint reader, Key
Aantal sleutels meegeleverd:	2 stuk(s)