Barska AX12760 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Barska AX12760 (2 pagina's) in de categorie Kluis. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Getting Started
1. Remove safe from packaging and remove Manual and
all accessories that came with the safe.
2. Insert emergency key into key access and turn
clockwise; move handle to unlock position and open
the safe. Remove key and keep in a secure location.
3. Open battery compartment and insert 4 AA
batteries. Do not mix old and new batteries.
4. Press “0” on keypad to wake up the safe and place
any finger on scanner. Few beeps will be heard and
red flashes will be seen then safe will unlock, turn
handle to unlocked position to open the door.
Note: Safe is in Factory Default Mode: ANY Fingerprint
can open the safe.
Fingerprint Registration
1. With safe open press and release initialization button
located inside the safe and place desired finger on
fingerprint scanner.
Successful Registration
2 beeps will be heard and 2 green flashes will be seen.
Unsuccessful Registration
2 quick beeps will be heard along with red flash. See reverse side for more information 6/19
BC611
WARNING
Test Registered Fingerprint
1. With Safe door open, turn handle to lock position
extending the bolts out.
2. Press “0” to wake up safe and place Registered
Fingerprint on the scanner. If green light is seen when
safe can be unlocked then registration was successful.
If safe opens but several beeps and red flash is seen
then registration was unsuccessful. Follow steps under
Fingerprint Registration to register your
desired fingerprint.
Pin Code Registration
1. Enter Current Pin Code (Default Pin Code:
“12312312312”); Green lights will be seen, then press
the “3” on keypad.
2. Enter new desired Pin Code between 4 – 11 digits and
if Pin Code is between 4 – 10 digits, press initialization
button on the back of the safe to finish. 1 long beep
will be heard and green light will be seen.
Note: Pin Code CANNOT start with “0”
Test Registered Pin Code
1. With Safe door open, turn handle to lock position
extending the bolts out.
2. Enter Registered Pin Code, If safe unlocks then
registration was successful. If safe does not unlock
then registration was unsuccessful, please follow steps
under Pin Code Registration to register your pin code.
Close / Open Safe Door
Open Safe Door with Fingerprint
Press “0” on keypad to wake up the safe and place
registered finger on scanner. Turn handle to unlocked
position and open safe door.
Open Safe Door with Pin Code
Enter Registered Pin Code and turn handle to unlocked
position to open safe door.
Closing Safe Door
Close door and turn handle to lock position to lock
the safe.
Manual for Biometric Keypad Safe
Read all instructions before using this safe
H
F
G
I
E
A
B
©2019 BARSKA®
855 Towne Center Drive | Pomona, CA 91767
(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com
A. Initialization Button
B. Battery Compartment
C. Bolts
D. Handle
E. Emergency Key Access
F. Fingerprint Scanner
G. Indicator Lights
H. Key Pad
I. External Battery Source
* Actual model may vary
CD
Lock
Unlock
- Safe can be opened by either Fingerprint, PIN code,
and/or Emergency Keys.
- If user resets the safe to Factory Default mode: ANY
fingerprint and Factory Default PIN code can open
the safe.
- Register BOTH Fingerprint and PIN code to disable
factory default mode.
- Register at least two different fingerprints and test a few
times before closing the safe door.
- To improve fingerprint accuracy, please register the same
finger 5 different times; please remove finger after each
successful registration
- Test with a non-registered fingerprint. If the safe opens,
the safe is still in Factory Default mode.
- Avoid leaving safe door open and unattended; it will allow
unauthorized individuals to add their fingerprints and/or
reprogram the safe, gaining full access to the safe and
the contents.
- Test the Emergency Keys and store them in a secure
place, NOT inside of the safe.
- To maximize the security and performance of the safe,
test registered fingerprints every 6 months.
- Test and make sure the safe works properly
before mounting.
- Mount the safe before use, the safe may tip forward if not
properly mounted.
- Keep children away from safe; they should not play
with or around the safe at anytime. Children at play
could accidentally get locked inside the safe or
accidentally pull on the safe door causing safe to tip
over if not properly mounted.
- Failure to follow these warnings could result in serious
injury or death.
9V Battery Not
Included
Silent Mode
Sound Off
Press and hold initialization button until 1 beep is
heard along with green flash. Sound is now disabled.
Sound On
Press and hold initialization button until 1 beep is
heard along with green flash.
Resetting the Safe
Take all the batteries out of the safe, press and hold
the initialization button inside the safe while
re-inserting the batteries, keep holding initialization
button until 3 beeps are heard and green flash is seen.
Test Safe to See if it is Reset
With Fingerprint Press “0” on keypad and place any
fingerprint on fingerprint scanner. Few beeps will be heard
and red flashes will be seen, safe will unlock. Turn handle
to unlocked position to open safe.
With Pin Code Press “12312312312” on keypad, beep will
be heard and green flash will be seen, safe will unlock.
Turn handle to unlocked position to open safe.
ANY fingerprint can now open the safe.
Default Pin Code “12312312312”
Low Battery Warning
An alarm sound and red flash will be seen when trying to
access safe. Safe may allow access still, but batteries should
be replaced as soon as possible.
Note: Can use 9v battery as an external power source. Place
9v battery under fingerprint module, touching the metal
contacts under the fingerprint module. Safe should power up,
if not switch the polarity of the 9v battery.
Care and Maintenance
- To maximize the security and performance of the safe, keep
Fingerprint Scanner clean; use a dry cloth to remove any
smudges or prints off the Fingerprint Scanner after
each use.
- Test registered fingerprints and PIN code every 6 months.
- Keep liquids away from the control panel. Spills on the
control panel will cause damage and possibly
electric shock.
- Secure safe in a proper area to prevent from falling and
causing damage or injury.
- DO NOT disassemble the product. For all repairs,
contact BARSKA Customer Service.
- DO NOT use chemicals or cleaning agents to clean
the safe.
Mounting Instructions
The safe may be mounted to a wall or floor. Be aware of
the load bearing. Failure to do so can result in personal
injury and/or damage to property. Use appropriate tools
when performing work and always use eye protection.
Wall Mounting
Do not mount the safe without anchoring to the wall.
- Find the studs in the wall, at your desired location. Most
studs are 16 inches or 24 inches apart.
- Check the wall for concealed wires or pipes.
- Measure the location of the pre-set drill holes; mark
their exact position onto the wall ensuring that the
studs or anything else behind will not interfere.
- Drill the appropriate size holes for the anchors you
are using.
- Carefully press the anchor into the holes at this time.
- Mount the safe by running screws from inside of the
safe and securing to anchors; ensure the safe is
mounted securely.
Floor Mounting
- Use proper drill tools depending on the type of floor you
are mounting the safe (wood, tile, or concrete).
- Measure the location of the pre-set drill holes; mark
their exact position onto the floor.
- Drill the appropriate size holes for the anchors you
are using.
- Carefully press the anchor into the holes at this time.
- Mount the safe by running screws from inside of the
safe and securing to anchors; ensure the safe is
mounted securely.
Biometric Keypad Safe
1 YEAR LIMITED WARRANTY
BARSKA warrants this new safe to be free of original defects in
material and/or workmanship under normal use for a period of
twelve (12) months from the date product is received by purchaser.
This warranty does not include damage caused by improper
installation or maintenance. Damage from misuse, abuse, accident
(such as dropping), normal wear and tear, fire, flood, or acts of
nature. Damage from service or repairs other than those
performed by BARSKA. Labor, cost and shipping charges for the
removal and replacement of defective parts beyond the initial
twelve-month warranty period. All transportation and shipping
charges. Removing or altering the seal under any circumstances
will automatically void the warranty.
This warranty is limited to original purchaser and is not
transferable. This warranty applies only to products purchased in
the United States.
Please email info@barska.com or call 1.888.666.6769 for Return
Merchandise Number (RMA#) before any returns. The RMA
number must appear on the outside of the shipping package.
Product must be packed carefully and sturdily in its original
packaging to prevent damage in transit and returned freight
pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA
products for service and/or replacement:
1. Please write your complete details (Name, Address,
Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order to cover inspection, shipping and
handling. Charges are as follows
$60 - Standard
$90 - Large
*Please allow 6-8 weeks for delivery.
BARSKA will examine and test returned product and repair or
replace defective part(s) or units with new part(s) or a new unit if
necessary within the warranty period. Purchaser is required to
remit amount above to BARSKA for return shipping and handling
at time product is returned. If repair is required after warranty
period expiration, purchaser will be charged for replacement parts
and return shipping.
BARSKA® Optics shall not be liable for any consequential,
incidental and/or contingent damages whatsoever. We will not pay
shipping, insurance or transportation charges from you to us, or
any import fees, duties and or taxes. This warranty supersedes all
previous BARSKA® Optics warranties.
Product specificaties
| Merk: | Barska |
| Categorie: | Kluis |
| Model: | AX12760 |
Heb je hulp nodig?
Als je hulp nodig hebt met Barska AX12760 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kluis Barska
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
26 Augustus 2023
Handleiding Kluis
- Kluis Philips
- Kluis Honeywell
- Kluis Abus
- Kluis Avanti
- Kluis Burg-Wachter
- Kluis Dometic
- Kluis Duralock
- Kluis EasySafe
- Kluis Ferm
- Kluis Filex
- Kluis FireKing
- Kluis First Alert
- Kluis Fluke
- Kluis Hama
- Kluis Handson
- Kluis M-Locks
- Kluis Master Lock
- Kluis Nauta
- Kluis Nedis
- Kluis Perel
- Kluis Phoenix
- Kluis Protector
- Kluis Renkforce
- Kluis ROMA
- Kluis Rottner
- Kluis Royal Safe
- Kluis Royal Sovereign
- Kluis Salvus
- Kluis Sentry
- Kluis Sistec
- Kluis SMC
- Kluis Sygonix
- Kluis Technomax
- Kluis Thule
- Kluis Toolland
- Kluis Topcraft
- Kluis Tulox
- Kluis Varo
- Kluis Westfalia
- Kluis Workzone
- Kluis Yale
- Kluis Jewel
- Kluis Juwel
- Kluis Olympia
- Kluis Oxloc
- Kluis First Austria
- Kluis Guzzanti
- Kluis Steren
- Kluis Conrad
- Kluis SereneLife
- Kluis Challenge
- Kluis MSW
- Kluis Hard Head
- Kluis Kidde
- Kluis SentrySafe
- Kluis CAWI
- Kluis Kreator
- Kluis Fichero
- Kluis Kreator-Varo
- Kluis Rottner Tresor
- Kluis Olymp
- Kluis Suncast
- Kluis Winholt
- Kluis Homak Security
- Kluis NOFIRE
- Kluis Stamony
Nieuwste handleidingen voor Kluis
15 November 2024
15 November 2024
15 November 2024
13 November 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
1 Oktober 2024
1 Oktober 2024