Baldwin Soho M516402RFD Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Baldwin Soho M516402RFD (4 pagina's) in de categorie slot. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
Baldwin Hardware Corporation
Mortise Lock Installation Instructions
TOOLS REQUIRED
1 Pencil
2 No. 2 and No. 3 Phillips Head
Screwdrivers
3 No. 1 and No. 2 Slotted Screwdrivers
4 1/8" Allen Head Wrench
5 3/4" Wood Chisel or Corner Chisel
6 Measuring Device
7 Lock Mortising Tool (Recommended)
8 Router and Lock Face Template
Note: In order to successfully install a mortise lock and trim, a minimum of average skill level is required with use of the above listed tools.
Read and understand the provided instructions BEFORE attempting to mark or cut the door and/or frame. If there are any questions
before you begin the installation, phone or visit your nearest Baldwin Distributor or contact the Technical Service Department at Baldwin
at 610.777.7811.
Diagram A
Diagram B
ENTRANCE HANDLESET
ENTRANCE LEVER/KNOB SET
9 Combination Square
10 Awl
11 Hacksaw
12 File (Wood Rasp and Metal)
13 Baldwin Aligning Tool
14 Drill and assorted Drill Bits (1/16", 1/8",
5/16", 3/8", 3/4", 1", 1-1/4")
15 Screw Wax or Soap
16 Powder Chalk, Graphite or Lipstick
CAUTION
Baldwin 2-1/2 and 2-3/4 backset Mortise locks are designed for residential use in UL-listed
fire-rated openings rated for 3-hour maximum. Meets U.S. UL10C (positive pressure) and
CANS-104M80. In the event of fire, lock will be permanently disabled when mechanism reaches
temperatures above 400ËšF. Use in accordance with local fire code regulations.
PK 1076A 8/05
Mark the Door Double Check Compatibility
of Door Stile & Trim
2
Mortise Lock Pocket
For Lock Body
3
Prepare for Lock Front
4
Mark the door at 37-1/2"- 40" above finished
floor, or if retrofit, at appropriate location to
coordinate with existing strike preparations.
This will be center line of the lock and will put
the knob/lever at 36" - 39" above the floor.
Make sure that the door stile will accommodate
the intended lock.
Mortise the pocket in the door 1/8" deeper
than the lock being installed. Refer to the
Installation Template Guide Chart (blue
sheet) for exact size of mortise pocket.
Rout for the lock front. Square the Corners.
Determine Hole Pattern
Required for Trim on
Blue Sheet
Determine hole pattern required for trim
using Installation Template Guide Chart
(blue sheet shown). Mark the listed holes on
the yellow lock template (figure 7) enclosed
with the lock. Ensure trim will not interfere with
door stop or extend over door panel or glass.
5
1
APrepare for Lock Front
5B
Mortise Lock Handleset Installation Instructions
DOOR CONDITIONS
Left Hand Right Hand
Outside
Outside
Left Hand
Reverse Bevel
Right Hand
Reverse Bevel
HAND OF DOOR IS ALWAYS DETERMINED FROM THE OUTSIDE
Here are some rules to follow:
• The outside of an exterior door is the
street or entrance side.
• The outside of a room is the hall side.
• The outside of a single communicating door is the
side from which the hinges are not visible when
the door is closed.
• The outside of a closet door is the room or hall side.
GENERAL NOTES
Paper template is designed for 1-3/4" thick doors. For extra thick
doors, measure backset from center of door edge. Tape supplied
template to the door to locate fastener pattern for lock and trim.
When installing hardware on metal or fiberglass doors, ensure the
door was designed to accommodate mortise locks. If in doubt,
check with your local door distributor or door manufacturer.
Removal of hardware from doors is recommended before painting
and finishing of the door. Allow paint/stain to fully cure before
reinstalling hardware, usually ten days to two weeks. Check paint
manufacturer instructions.
Retain these instructions in a safe place should you need to
disassemble the lock trim or require Baldwin’s assistance.
For 1-3/4" doors, fold the yellow lock template
and attach to door using Installation Template
Guide. Mark door at appropriate locations for
lock and trim. MARK APPROPRIATE BACKSET.
(Extra thick door conditions, see General Notes.)
Metal template 8498.000 is available for purchase.
6 7 Mark Door Drill Holes
8
Drill appropriate holes as indicated on yellow
lock template. DO NOT OVERSIZE HOLES.
Only top two holes are drilled for knob to
knob and lever to lever sets.
Install Lock Insert Spindle
11
Size Thumbpiece
12
Drill two pilot holes for the lock face, adjust the
bevel and install the lock. Shim between the lock
and door on cylinder side as shown to prohibit
the cylinder from pulling the lock case off center.
(Failure to shim the lock may cause the cylinder
to sit unevenly on the surface of the trim.)
For handleset trim install the spindle from the
inside with V groove facing bottom door hinge
and thread the screw and lock washer into
the spindle from the outside. Tighten securely.
For knob to knob and lever to lever sets, install
spindle from outside - go to step 13.
Cut the thumbpiece so that it will fully
engage the lift lever on the bottom of
the lock.
Place the cylinder through the trim. Partially insert
key into cylinder. Thread the cylinder into the lock
until it is against the trim and Baldwin name is
horizontal. For knob to knob and lever to lever
sets - Install aligning bushing and fasten trim with
supplied screws. Remove bushing - go to step 16.
Start the thru-bolts which will hold the
exterior trim. (Use screw cover washer
under the bottom thru-bolt.) Tighten
both securely.
Install Thru-Bolts
Install Cylinder
13
Thread the cylinder plug into interior side of
lock. Place a strip of tape over plug to keep it
from turning. Notch must be located as shown.
(Double cylinder functions: OMIT THIS STEP.)
Install Cylinder Plug
9 10
Cut
Cut Relief Pockets
Cut the relief pockets 3/8" deep on both
sides for the Latch Hinge, 2-1/2" and 2-3/4"
backset only. (Does not apply for 1"front.)
Metal Paper
Shim
14
Product specificaties
| Merk: | Baldwin |
| Categorie: | slot |
| Model: | Soho M516402RFD |
Heb je hulp nodig?
Als je hulp nodig hebt met Baldwin Soho M516402RFD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding slot Baldwin
5 Februari 2025
5 Februari 2025
5 Februari 2025
5 Februari 2025
5 Februari 2025
5 Februari 2025
5 Februari 2025
5 Februari 2025
5 Februari 2025
5 Februari 2025
Handleiding slot
- slot Honeywell
- slot Abus
- slot Acco
- slot Aqara
- slot Axa
- slot Be Cool
- slot Burg-Wachter
- slot Heidemann
- slot Kensington
- slot Kogan
- slot Logilink
- slot Manhattan
- slot Master Lock
- slot Nemef
- slot Newstar
- slot SECURITY Plus
- slot Silverline
- slot Sweex
- slot Targus
- slot Olympia
- slot Steren
- slot Tryten
- slot Hamlet
- slot SIIG
- slot Extel
- slot PNY
- slot Tripp Lite
- slot Kidde
- slot Chief
- slot Chamberlain
- slot Lindy
- slot Kindermann
- slot Homematic IP
- slot AMX
- slot StarTech.com
- slot Kwikset
- slot Vimar
- slot Panduit
- slot V7
- slot Kasp
- slot Squire
- slot Unicol
- slot TooQ
- slot Nuki
- slot Multibrackets
- slot Rocstor
- slot Welock
- slot Middle Atlantic
- slot Lockly
- slot SOREX
- slot Eura
Nieuwste handleidingen voor slot
30 Januari 2025
19 December 2024
6 December 2024
2 December 2024
2 December 2024
20 November 2024
17 November 2024
12 November 2024
25 September 2024
11 September 2024