Balboa SpaTouch3 Handleiding

Balboa Wellness SpaTouch3

Lees hieronder de 📖 handleiding in het Nederlandse voor Balboa SpaTouch3 (35 pagina's) in de categorie Wellness. Deze handleiding was nuttig voor 131 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/35
spaTouch™ 3 User Guide
42344_Rev D 1
User Guide
Panel Software Version: 1.02 and above (view page 19)
VISIT US ONLINE
www.BalboaWaterGroup.com
spaTouch™ 3 User Guide
42344_Rev D 2
spaTouch 3 Plus
spaTouch 3
spaTouch 3 Plus
spaTouch 3
spaTouchTM 3+
7“ Display (17.78 cm Display)
spaTouchTM 3
5“ Display (12.70 cm Display)
THE MAIN SCREEN 04
WAKE UP THE PANEL, NAVIGATION & COMMON BUTTONS 06
SET TIME-OF-DAY 09
SET THE TEMPERATURE 10
RUN SPA DEVICES 12
SET FILTER CYCLE TIME 13
RESTRICT OPERATIONS 15
SPA BEHAVIOR 17
DIAGNOSTICS SCREEN 19
HEAT SETTINGS 22
SETTINGS SCREEN 24
FILL IT UP! 26
MESSAGES 27
TOPSIDE PANEL INSTALLATION 30
APPENDIX 31
WARNING 32
INFORMATION 33
spaTouch™ 3 User Guide
42344_Rev D 3
TABLE OF CONTENTS
spaTouch™ 3 User Guide
42344_Rev D 4
Main Screen Icons
THE MAIN SCREEN
A B C D
T
S
R
A
A - Panel Sleep
B - Temperature Range
High:
Low:
C - Heat Mode
Ready:
Rest:
Ready-in-Rest:
D - Ozone Running:
E - Filter Cycles
Filter Cycle 1:
Filter Cycle 2: (Optional Feature)
Filter Cycles 1 & 2:
F - Cleanup Cycle (Optional Feature)
G - Panel Locked and/or Settings Locked
H - WiFi (Local or Cloud Connection)
I - Time-of-Day
J - Secondary Button/Display
K - Invert Display
L - Settings
M - bbaTM versions 2 and 3 (Balboa Bluetooth Audio)
N - Light (or TM if installed).
Both icons change from white to color
when these devices are powered On.
O - Spa
P - Heater Status
Q - Message Button (May Appear)
Information:
Reminder:
Error - Normal Error or Warning:
   Error-Spawillnotfunctionuntilxed:
R - Water Temperature
S - Water Temperature Bar
T - Set Temperature Arrow
E F H
A O N MP L
The system conguration determines the number
of icons that appear on the Main Screen. Your Main
Screen may have fewer or different icons.
K
The icons in this row are
functioning buttons.
J
I
Q
G
spaTouch™ 3 User Guide
42344_Rev D 5
Important information about spa operations can be
seen on the Main Screen. Most features, including
Set Temperature adjustment, can be accessed from
this screen. The actual water temperature can be
seen, and the Set Temperature can be adjusted (see
page 10). Time-of-Day, Ozone and Filter status are
available, along with other messages and alerts. The
selected Temperature Range is indicated in the upper
left corner. A Lock icon is visible if the Panel and/
or Settings are locked. Near the bottom of the screen,
at certain times an indicator may appear showing that
a message is waiting. Touch this indicator to go to the
Message Display Screen. On that Screen some of the
messages can be dismissed. For more on the Message
Display Screen, see page 27.
When the spa is powered On, four dashes appear
(A) in the Water Temperature display for one minute.
The dashes indicate that the spa is checking the
water temperature. After the pump runs for 1 minute,
the dashes disappear and the water temperature is
displayed (B). The dashes may reappear after the
pump has not run for one hour.
Spa Status
A
B
spaTouch™ 3 User Guide
42344_Rev D 6
Controlling your spa is easy with the intuitive graphical user
interface (GUI). This section describes how to navigate and
use the GUI.
Wake Up the Panel
The screen is blank when it is in sleep mode. When you touch
the blank screen, one of three screens will appear:
1 - The Main screen will appear (A4). The panel is awake.
2 - The icon will appear (A2). Wake up the panel by
pressing the icon and then the icon.
3 - The hand icon will appear. Wake up the panel by pressing
the hand icon (A1) and then swiping in the direction of
the arrows.
The panel automatically goes into sleep mode when it is not
usedforaspeciedduration.Thedurationcanbeadjusted
(view Panel on page 25).
Put the Panel to Sleep
Put the panel to sleep by pressing the Sleep button (A3).
Panels may or may not have a sleep button.
Buttons
A variety of button styles provide quick access to functions
and settings. The large temperature display is a button (B)
that controls the Set Temperature. The whole bottom row of
the Main screen contains buttons (C).
Mini Player Button (Set Temperature/Time)
The Mini Player button gives fast access to the Set
Temperature and time (D). Show or hide the Mini Player
button by pressing the Heater Status button once (E).
Mini Player Button (Music)
The Mini Player displays music controls (F), if your spa is
equipped with bbaTM (Balboa Bluetooth Audio) and it is
activated. Hide the Mini Player button by pressing the
HeaterStatusbuttontwice(G).Therstpressdisplaysthe
Set Temperature/Time Mini Player button. The second press
hides the Mini Player button.
B
C
D
E
F
G
H
A2
A1
WAKE UP THE PANEL, NAVIGATION
& COMMON BUTTONS
A4
A3
bbaTM button (H)
If bbaTM is activated, pressing the bbaTM button (H) once
displays the Mini Player (F) with music controls. Pressing
the bbaTM button (H) a second time opens the Music
screen ( I ) , If bbaTM is activated, a white ring appears
around the button, as shown here ( I ).
If bbaTM is not activated, pressing the bbaTM button (H)
once opens the Music screen ( I ).
If your spa is equipped with bbaTM, refer to the bbaTM
user guide that came with the spa. If a user guide was
not included, please contact the spa dealer or
spa manufacturer.
Screen Names
Screen names appear in the top row of the screen. For
example,thisistheSettingsscreen(J).Screennames
are referenced throughout this user guide.
Navigation
Navigate screens and/or lists with the
following buttons:
Swiping & Selecting Items in Lists
Swipealist(N)tondthesettingyouwant.Thelistwill
have an arrow (M) that indicates the current setting. If
your desired setting appears but is not aligned with
the arrow, tap the desired setting to make it align with
the arrow. The temperature list will disappear when you
tape anywhere outside of it.
spaTouch™ 3 User Guide
42344_Rev D 7
A
N
M
J
K
L
F
G
H
I
Up
Down
Back (L).
Left (K)
Right (K)
spaTouch™ 3 User Guide
42344_Rev D 8
Information Message
Reminder Message
Error - Normal Error or Warning
Error - Spa will not function until xed
Clear Button
Exit Button
Saving & Canceling
After you input a new setting, press the Save button
(B). After you press Save, the change is complete. If you
don’t want to apply a new setting, press the
Cancel button (A).
Message Buttons
Message buttons provide reminders to help you keep
your spa running smoothly. Message buttons also
provide warning information that helps spa technicians
with troubleshooting.
When a message button appears (C), press it to view
thecorrespondingmessage(D)or(G).PresstheExit
button (E) to go back to the Main screen, or press the
Clear button (F) to dismiss the message.
Buttons vary depending on the type of message. View
the list below.
E
C
D
F
A B
G
spaTouch™ 3 User Guide
42344_Rev D 9
Follow this sequence to set the time-of-day.
• In the Main screen, press the Settings button (B).
• In the Settings screen, press the Time button (C).
• In the Time of Day screen, press the Time button (D).
• Setting dials appear. Swipe these dials (F) to set
the time. If your desired time value appears but is
not aligned with the arrow, tap the desired time
value to make it align with the arrow.
• Press the Save button (G) to save your settings. Or,
press the Cancel button (E) to cancel your settings.
Setting the time-of-day is important for determining
ltrationtimesandotherbackgroundfeatures.If
Time-of-Day needs to be set, the Information Message
button (A) appears on the Main screen; view the
previous page for more information on the different
types of Message buttons.
NOTE: If power is interrupted to the system,
Time-of-Day will be maintained for several days (this
only applies to some systems).
SET THE TIME-OF-DAY
A
C
A
EA
F
A
D
Be sure to set the
Time-of-Day
A
A
A
B
A
G
Temperature
Menu
E
CCurrent
Set Temperature
spaTouch™ 3 User Guide
42344_Rev D 10
In this example we will set the Set
Temperature to 102.
Press the water temperature display button (A) to
make the temperature menu appear (B). The center
boxwiththearrow(C)indicatesthecurrent
Set Temperature.
If 102 is already showing, but just not centered (D),
touch it to center it (E).
If 102 is not showing (B), swipe the temperature
menu until 102 appears (D).
If 102 appears after swiping but does not stop in the
centerbox(D),press102.Pressing102makesitshift
tothecenterbox(E).
Press the water temperature display (A) to make the
temperature menu disappear. The Set Temperature
is now 102.
SET THE TEMPERATURE
A
A
D
B
•
•
•
•
•
F
spaTouch™ 3 User Guide
42344_Rev D 11
How do I view the Set Temperature?
Press the Heater Status button (A), and the Set
Temperature appears in the Mini Player button (B).
Press the Heater Status button again to make the Mini
Player button disappear.
Set Temperature is represented numerically and by
a blue arrow (D). Water temperature is represented
numerically and by a blue status bar (C). The difference
between water temperature and Set Temperature is
represented by the gap between the blue status bar
and the blue arrow (E). If there is no gap, the water
temperature and Set Temperature are equal.
Can I change the Set Temperature with the mini
player button?
Yes you can. The mini player button and temperature
display button function the same way in this regard.
Press the mini player button to view the temperature
menu. Select the desired temperature, and press the
mini player button again to make the temperature
menu disappear. You have now programmed a new
Set Temperature.
How do I know when the heater is On?
The center of the Heater Status icon turns red (A)
when the heater is On. The Heater Status icon appears
in the top left corner of the Spa screen (F) when the
heater is On.
A
B
E
C
D
Heater Off Heater On
Note: the Heater Status
button icon ashes during
heater start-up; this is normal.
spaTouch™ 3 User Guide
42344_Rev D 12
Press the Spa button (A) to view the Spa screen.
Press these buttons (B) to run spa devices. Some
devises may only turn On and Off, while other
devices may have multiple speeds/states. Your spa
congurationdeterminesthenumberofbuttonsand
the function of the buttons in the Spa screen. One Spa
screendisplayssixbuttons,maximum.Ifmorethansix
buttonsexists,anavigationbuttonappears(D).Press
thenavigationbutton(D),orswipe,toviewthenext
Spa screen. Press the Back button (C) to navigate to
the Main screen.
IftheJetsareleftrunning,theywillturnoffaftera
time-out period.
If the Spa has a circulation pump, a circulation pump
icon will appear in the Spa screen to indicate its
activity only (the icon is not a functioning button).
The circulation pump can be controlled with a button
during Priming mode (view page 26).
Ifthespadoesnothaveacirculationpump,thenJets
1 may turn On automatically at times. In these cases,
pressingtheJets1buttonwilljustchangespeeds,but
willnotturnOffJets1.
RUN SPA DEVICES
Main Screen
C
A
Spa Button
B D
spaTouch™ 3 User Guide
42344_Rev D 13
Follow these steps to set the time for Filter Cycle 1.
• Press the Settings button (A) on the Main screen.
• Press the Filter button (B) on the Settings screen.
• Press the Start button (E) on the Filter Cycles screen.
• SettheStartTimewiththesedials(J)onthe
F1 End screen.
• Press the Save button ( K ) to save your settings, or
press the Cancel button ( I ) to cancel your settings.
• Press the End button (F) on the Filter Cycles screen,
and follow the same steps to set the End Time.
• Once the Start and End Times are set, press the Save
button (G) on the Filter Cycles screen.
• Once Start and End Times are set, the Duration
appears here (H). You have now set the time for
Filter Cycle 1. The white ring (C) indicates that Filter
Cycle 1 is enabled (it is always enabled).
Follow the same steps noted above to set the time for
Filter Cycle 2.
How can you tell if Filter Cycle 2 is enabled?
Filter Cycle 2 is enabled when a white ring appears
around the button.Forexample,FilterCycle1is
enabled (C) in this screen, and Filter Cycle 2 is disabled
(D). Press the button to enable/disable Filter Cycle
2. A Filter Cycle 2 will only run if it is enabled.
Note: It is possible to overlap Filter Cycle 1 and Filter Cycle 2,
which will shorten overall ltration by the overlap amount.
SET FILTER CYCLE TIME
A
B
A
IA
JA
K
Keep your water clean
and ready to enjoy
A
A
A
E
A
H
A
C
A
F
A
D
A
G
spaTouch™ 3 User Guide
42344_Rev D 14
Adjusting Filtration
Circulation Pump Modes
Some spas may be manufactured with Circ Pump
settingsthatallowprogrammingltrationcycle
duration. Some Circ Modes are pre-programmed to
operate 24 hours a day and are not programmable.
Refer to the spa manufacturer’s documentation for any
Circulation Pump Mode details.
Purge Cycles
In order to maintain sanitary conditions, as well as
protect against freezing, secondary water devices will
purge water from their respective plumbing by running
brieyatthebeginningofeachltercycle.(Some
systems will run a certain number of purge cycles per
day,independentofthenumberofltercyclesperday.
In this case, the purge cycles may not coincide with the
startoftheltercycle).IftheFilterCycle1durationis
set for 24 hours, enabling Filter Cycle 2 will initiate a
purge when Filter Cycle 2 is programmed to begin.
The Meaning of Filter Cycles
1.Theheatingpumpalwaysrunsduringtheltercycle*
2. In Rest Mode, heating only occurs during the
ltercycle
3.Purgeshappenatthestartofeachltercycle
(on most systems).
* For example, if your spa is set up for 24/hour
circulation except for shutting off when the water
temperature is 3˚F/1.3˚C above the set temperature,
that shutoff does not occur during lter cycles.
Additional Settings
Auxiliary Panel(s)
Specic Buttons for Specic Devices
IfthespahasanAuxiliaryPanel(s)installed,pressing
buttons on that panel will activate the device indicated
for that button. These dedicated buttons will operate
just like the Spa Screen buttons (see page 12) and the
equipment will behave in the same manner with each
button press.
Model #: AX10
Model #: AX20
Model #: AX40
Auxiliary Panels
Thefollowingexamples
show how to lock and
unlock the Panel.
LOCK PANEL
• Press the Settings button (A) on the
Main screen.
• Press the Locks button (B) on the
Settings screen.
• Press the Panel button (C) on the Locks screen.
“Lock Panel” will appear at the top of the screen (D).
• Press-&-hold“LockPanel”(D)forveseconds.After
 vesecondsaLockicon (E) will appear in the
top row. The lock icon also appears in the top row of
the Main screen. The panel is now locked.
spaTouch™ 3 User Guide
42344_Rev D 15
RESTRICT OPERATIONS
A
B
A
C
A
E
( Continued on next page )
A
D
A
A
UNLOCK PANEL
• Press the Panel button (F) in the Locks screen,
and “Unlock Panel” will appear at the top of
the screen (G).
• Press-&-hold“UnlockPanel”(G)forveseconds.
 AftervesecondstheLockicon will disappear
from the top row ( I ) of the Locks screen. The panel
is now Unlocked.
The control can be restricted to prevent unwanted
use or temperature adjustments. Locking the Panel
prevents the controller from being used, but all
automatic functions are still active.
LOCK & UNLOCK SETTINGS
Follow the same steps noted above to lock and
unlock Settings.
LockingtheSettingsallowsJetsandotherfeatures
to be used, but the Set Temperature and other
programmed settings cannot be adjusted. Settings
Lock allows access to a reduced selection of menu
items. These include Filter Cycles (view only), Invert,
Information and Fault Log. They can be seen, but not
changed or edited.
Can Settings and Panel be locked simultaneously?
Yes. The lock icon (K) appears if Settings or Panel or
both are locked. The current lock states are noted on
the right side of the buttons (H).
spaTouch™ 3 User Guide
42344_Rev D 16
A
F
G
A
I
A
K
A
H
A
J
Pumps
Pumps drive water and air through the jets. A pump
typically has one or two speeds. If left running, a pump
will turn off after a time-out period.
Circulation Pump
A circulation pump is usually smaller, quieter, and
requires less energy than a pump used for jets. A
circulation pump typically has one speed and circulates
waterthroughthespa’sltrationsystemtokeepthe
water clean. the circulation pump also runs when the
blower or any other pump is on.
Non-Circulation Pump Systems
(or “non-circ systems”)
If a spa does not have a circulation pump, another
pump will function in its place. The low-speed of pump
1 runs when the blower or any other pump is on. If the
spa is in Ready Mode (See page 22), Pump 1 low may
also activate for at least 1 minute at various intervals to
detect the spa temperature (polling) and then to heat
to the set temperature if needed. When the low-speed
turns on automatically, it cannot be deactivated from
the panel, however the high speed may be started.
spaTouch™ 3 User Guide
42344_Rev D 17
SPA BEHAVIOR
Circulation Pump Modes
If the system is equipped with a circulation pump, it will
beconguredtoworkinoneofthreedifferentways:
1. The circulation pump operates continuously (24
hours)withtheexceptionofturningofffor30minutes
at a time when the water temperature reaches 3°F
(1.5°C) above the set temperature (most likely to
happen in very hot climates).
2. The circulation pump stays on continuously,
regardless of water temperature.
3. A programmable circulation pump will come on
when the system is checking temperature (polling),
duringltercycles,duringfreezeconditions,orwhen
another pump is on.
ThespecicCirculationModethatisusedhasbeen
determined by the Manufacturer and cannot be
changedintheeld.
Filtration and Ozone
If a spa does not have a circulation pump, Pump 1
lowandtheozonegeneratorwillrunduringltration.
On circ systems, the ozone will generally run with the
circulationpump,butcanbelimitedtoltrationcycles.
(On some circ systems, Pump 1 low will run along with
thecirculationpumpduringltration.)
Mostsystemsarefactory-programmedwithonelter
cycle that will run in the evening (assuming the time-
of-day is properly set) when energy rates are often
lower.Theltertimeanddurationareprogrammable.
Asecondltercyclecanbeenabledasneeded.Atthe
startofeachltercycle,thewaterdeviceslikeblower,
misterdevice(iftheseexist)andotherpumpswillrun
brieytopurgetheplumbingtomaintaingood
water quality.
Freeze Protection
If the temperature sensors within the heater detect
a low enough temperature, then the water devices
automatically activate to provide freeze protection.
The water devices will run either continuously or
periodically depending on conditions. In colder
climates, an optional freeze sensor may be added
to protect against freeze conditions that may not be
sensedbythestandardsensors.Auxiliaryfreezesensor
protectionactssimilarlyexceptwiththetemperature
thresholds determined by the switch. See your dealer
for details.
Clean-up Cycle (optional)
When a pump or blower is turned on by a button press,
a clean-up cycle begins 30 minutes after the pump
or blower is turned off or times out. The pump and
the ozone generator will run for 30 minutes or more,
depending on the system. On some systems, you can
change this setting.
Clean-upcyclesallowthespatolterlesswhenthespa
isusedlessoften,andtoltermorewhenthespais
used more often.
spaTouch™ 3 User Guide
42344_Rev D 18
GFCI Test (Continued)
Perform a GFCI Test
Start at the Main screen and follow these steps to
manually test the GFCI.
• Press the Settings button on the Main screen.
• Press the Diagnostics button on the
Settings screen.
• Press the GFCI Test button (C) on the
Diagnostics screen. The GFCI Test screen will appear.
If the GFCI Test status is “Passed” (F), you may not
need to perform this test.
If the GFCI Test status is “Armed” (D), proceed to the
nextstep.
• Press the Test button (E).
Withinapproximately12seconds,oneofthefollowing
two things will happen:
1 - The spa powers down. After the spa powers down,
go to the GFCI and power up the spa. The spa goes
into Priming Mode when it is powered up. When
Priming Mode is complete, navigate to the GFCI Test
screenandconrmthatitsays
“GFCI Status - Passed” (F).
2 - A “GFCI Test Failed” message appears. In this case,
contactaqualiedservicetechnician.Whileyouwait
for the spa technician to arrive, the spa can be run
normally for a time by cycling the power.
Reset Button:
Only use the Reset Button prior to moving the spa to
a new location. Pressing the Reset the button forces a
new Test to be performed at the new location.
A B C
CE Product
CE registered systems do not have an RCD Test
Feature due to the nature of the electrical service. The
end-user must be trained how to properly test and
reset the RCD.
spaTouch™ 3 User Guide
42344_Rev D 21
E
D
F


Product specificaties

Merk: Balboa
Categorie: Wellness
Model: SpaTouch3

Heb je hulp nodig?

Als je hulp nodig hebt met Balboa SpaTouch3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden