Azden WHD-PRO + I Handleiding

Azden Microfoon WHD-PRO + I

Lees hieronder de 📖 handleiding in het Nederlandse voor Azden WHD-PRO + I (4 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

WHD-PRO + i AUDIO KIT

WR WM- -PRO - - -PRO EX 503 - - SGM 990 i CABLE-HX-

INSTRUCTION MANUAL

WARNING

 Do not store or use the products in high heat or humidity.

 Do not use near a broadcast staon, airport or plane. You must change the frequencies if you are

interfering with other transmiers.

 The system will work connuously for 10 hours on one set of baeries. If sound quality is poor,

change baeries.

 Remove baeries when the system is not in use.

Thank you for purchasing the AZDEN WHD PRO Audio Kit. The following contents are included in your kit:-

-1 x WR PRO VHF Receiver

-1 x WM PRO VHF Belt Pack Transmier-

-1 x EX 503 Lavalier Microphone

-1 x SGM 990 Direconal Microphone

-1 x HX i Smartphone Connector Cable

The PRO systems operate in the low interference VHF band and have 2 switchable frequencies, -

169.445 (F1) and 170.245 (F2). You should select the quieter frequency for use.

The systems conforms to Part 90 of the FCC rules. You should contact the FCC oce for ling forms.

1. Loading Baery

Open the baery compartment lid by sliding it down and raising the lid. Insert a 9 volt -

baery into the baery compartment with the correct polarity. Direcons are on the inside of the

baery compartment. Do not force the baery compartment lid to close. If it does not close easily,

turn the baery around and try again.

2. Power/Frequency Selector Switch

This slide switch is used to turn the unit on and o as well as to select a frequency. When

not using the WR PRO, make sure that the switch is turned to OFF. -

3. Signal Indicator

This LED has 2 funcons: When you rst turn the Power/Frequency Selector Switch of the

Receiver on, but if the Transmier is not on, the LED will show red indicang that the baery is good.

If both the Transmier and the Receiver are on and they are on the same frequency, the Receiver LED

will show green and the Transmier LED will show red.

WR- PRO RECEIVER

4. Shoe Mount

The Receiver comes with an aached shoe mount for mounng to a camera. You can also aach

the Receiver with the enclosed loop and hook fastener. The shoe mount can be easily removed from

the Receiver by unscrewing the Phillips head screw in the center of the shoe mount.

5. Output Plug

Connect the plug from the Receiver into the camera’s “STEREO EXT. MIC” jack.

6. Telescopic Antenna

Fully extend the antenna for the best recepon.

7. Earphone Jack

Plug an earphone (not included) into the jack to monitor the sound you are recording.

1. Baery

Unscrew lower half of the microphone by turning the case counterclockwise. Insert one AAA

Alkaline baery into the case making sure polarity is correct. Close the case by turning it clockwise.

DO NOT OVER TIGHTEN or you may strip the threads.-

2. -Shock Mount Holder

- -The SGM 990 is supplied with a shock mount holder. Snap the rear poron of the microphone

into the holder. To secure the holder to a camera shoe, slide the holder into the camera shoe and

ghten the thumbwheel by turning it clockwise.

3. Windscreen

Slide the windscreen over the front end of the microphone and cover all the vents on the barrel.

4. 3.5mm Stereo Output Mini Plug-

Insert the plug into your camera’s “STEREO EXT. MIC” jack.

5. Power Switch

Turn the power switch to “ON” for normal operaon. When not in use, turn the microphone to

“OFF” to avoid draining the baery.

6. Long/Short Paern Switch

Slide the switch upward (or toward the front of the microphone) to turn on the LONG seng to

enable the Super cardioid pickup paern for further distances or slide it back to SHORT for a -

direconal omni style pickup paern.-

WM- PRO TRANSMITTER

SGM 990 SHOTGUN MICROPHONE-

1. Loading Baery

Insert (1) 9 volt baery into the baery compartment. Be careful not to force the baery -

compartment lid closed.

2. Microphone

Plug the EX 503 (lavalier mic). Extend the cord as much as possible since it doubles as the -

transmier’s antenna.

3. Power/Frequency Selector Switch

This switch is used to turn the unit on and o as well as to select a frequency.

4. Mounng

The Transmier can be aached to a belt using the clip provided or placed in a pocket.

1. -To use the HX i cable with your smartphone or tablet, insert the TRRS (4 pin male) end of the -

cable into your smartphone or tablet.

2. If you are using the wireless microphone system, insert the STEREO (3 pin) end of the WR PRO - -

receiver’s output cable into the HX i-

3. If you are using the SGM 990, insert the STEREO (3- -pin) end of the output cable into the HX-i.

SGM 990 SHOTGUN MICROPHONE-

TYPE: Super Cardioid Electret Condenser

SENSITIVITY: - 40dB (at 1kHz 1V/Pa)

FREQUENCY RESPONSE: 100Hz—20kHZ

OUTPUT IMPEDANCE: LON 1. G: 7kΩ

SHORT: 076 Ω

POWER SOURCE: DC1.5V AAA size baery

MAX SPL: 100dB

SIGNAL NOISE RATIO: More than 60dB

DIMENSIONS: ɸ18.2mm X 177mm

WEIGHT: 52g (not including the baery)

POLAR PATTERN

WM-PRO TRANSMITTER

TRANSMISSION FREQUENCY: F1—169.445MHz

—170.245MHzF2

MODULATION SYSTEM: FM modulaon

BATTERY: 9V x 1

POWER CONSUMPTION: 30mA

DIMENSIONS: 86(h) x 60(w) x 21.5(d)mm

WEIGHT (including baery): 98g

MICROPHONE: Electric Condenser (EX 503)-

WR-PRO RECEIVER

RECEPTION FREQUENCY: —169.445MHz F1

F2—170.245MHz

Double Superheterrodyne System

RECEPTION SENSITIVITY: 2µV at S/N 40dB

BATTERY: 9V x 1 (not included)

POWER CONSUMPTION: 25mA

MONITOR OUTPUT: Voltage: 1V

(Load: 30Ω, Modfreq: 1KHz, Dev: ±7KHz)

MICROPHONE OUTPUT: Voltage: 8mV

(Load: 10KΩ, Modfreq: 1KHz, Dev: ±7KHz,

Impedance: 300Ω)

DIMENSIONS: 86(h) X 60(w) X 21.5(d)mm

WEIGHT: 128g (including baery)

HX- i ADAPTER CABLE

SPECIFICATIONS

Product specificaties

Merk:	Azden
Categorie:	Microfoon
Model:	WHD-PRO + I
Microfoontype:	Draagbare microfoon
Frequentie:	169.445, 170.245 MHz
Signaal/ruis-verhouding:	40 dB
Receiver afmetingen (B x D x H):	60 x 21.5 x 86 mm
Ontvanger type:	Cameragemonteerde ontvanger
Frequentierespons microfoon:	150 - 18000 Hz
Zendretype:	Bodypackzender
Type werkfrequentie:	Zeer hoge frequentie (VHF)
Receiver gewicht:	128 g
Aantal ontvangers inbegrepen:	1
Aantal zenders inbegrepen:	1
Aantal microfoons inclusief:	1
Aantal ontvangstfrequenties:	2
Aantal transmissiefrequenties:	2