AXESS AXTO-TY1 Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor AXESS AXTO-TY1 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
AXTO-TY1
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com Ā© COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 4/26/22 INSTAXTO-TY1
ATTENTION: With the key out of the
ignition, disconnect the negative battery
terminal before installing this product. Ensure
that all installation connections, especially the
air bag indicator lights, are plugged in before
reconnecting the battery or cycling the ignition
to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
ā€¢ Crimping tool and connectors, or solder gun,
solder, and heat shrink
ā€¢ Tape ā€¢ Wire cutter ā€¢ Zip-ties
ā€¢ Small ļ¬‚at-blade screwdriver
TABLE OF CONTENTS
Connections .........................................................2-3
Installation .............................................................3
Programming .........................................................3
Audio level adjustment .........................................3
Wiring diagram ......................................................4
Toyota Digital Ampliļ¬er Interface 2001-2015
ā€¢ Designed for ampliļ¬ed models
ā€¢ Retains balance and fade
ā€¢ USB Micro-B updatable
ā€¢ AXTO-TY1 harness
ā€¢ AXTO-TY1 interface
ā€¢ 16-pin harness with stripped leads
APPLICATIONS
See inside front cover
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date
vehicle speciļ¬c applications
2
APPLICATIONS CONNECTIONS
LEXUS
ES Series 2007-2012
ES Series (w/ multi disc) 2002-2006
GS Series 2001-2005
IS Series 2002-2005
LS Series 2001-2006
RX Series 2004-2009
SC Series 2002-2010
TOYOTA
4-Runner 2003-2013
Avalon 2005-2010
Avalon 2011-2012
(Camry) Solara 2004-2008
Camry (w/o nav) 2012-2013
Camry 2007-2011
Corolla 2003-2011
TOYOTA (Cont.)
FJ Cruiser 2011-2014
Highlander 2008-2013
Highlander Hybrid 2008-2012
Matrix 2005-2012
Prius 3rd Gen (w/o nav) 2012-2015
Plug-In (PHV) (w/o nav) 2012-2015
Prius 2004-2011
Rav-4 2004-2013.5
Sequoia 2005-2012
Sequoia (w/o nav) 2013
Sienna 2004-2014
Tacoma 2005-2013
Tundra 2006-2013
Tundra (Double Cab) 2004-2005
Venza (w/ SD card based nav) 2013-2014
Venza 2009-2012
From the 16-pin harness with stripped leads to the aftermarket radio, connect as indicated:
ā€¢ wire to the left front (+) speaker output.White
ā€¢ wire to the left front (-) speaker output.White/Black
ā€¢ wire to the right front (+) speaker output.Gray
ā€¢ Gray/Black wire to the right front (-) speaker output.
ā€¢ wire to the radioā€™s left rear (+) speaker output.Green
ā€¢ wire to the radioā€™s left rear (-) speaker output.Green/Black
ā€¢ wire to the radioā€™s right rear (+) speaker output.Purple
ā€¢ wire to the radioā€™s right rear (-) speaker output.Purple/Black
ā€¢ wire to the ampliļ¬er turn on wire. Blue/White
Note: This wire must be connected to hear sound from the factory ampliļ¬er.
Tape off and disregard the following (6) wires, they will not be used in this application:
Red, , , , Brown Light Green Blue/Pink Green/Purple Orange/White,
Continued on the next page
For refer toDash Disassembly Instructions, metraonline.com.
Enter the year, make, and model of the vehicle in the
Vehicle Fit Guide for Radio Install kits.
3
REV. 4/26/22 INSTAXTO-TY1
From the AXTO-TY1 harness to the aftermarket radio, connect as indicated:
ā€¢ wire to the ground wire.Black
ā€¢ Yellow wire to the battery wire.
ā€¢ wire to the accessory wire.Red
ā€¢ wire to the power antenna wire.Blue
ā€¢ wire to the illumination wire. (if applicable)Orange
ā€¢ wire connect this to the ground wire if there is noise in the system. Black/White
With the key in the off position:
1. Connect the , and the 16-pin harness with stripped leads AXTO-TY1 harness into the
AXTO-TY1 interface.
2. Connect the AXTO-TY1 harness to the wiring harness in the vehicle.
1. With the vehicle and radio turned on, turn the volume up 3/4 of the way.
2. With a small ļ¬‚at-blade screwdriver, adjust the potentiometer clockwise to raise the audio
level; counter clockwise to lower the audio level.
3. Once at a desired level, audio adjustment is complete.
1. Turn the key (or push-to-start button) to the ignition position and wait until the radio
comes on. The factory ampliļ¬er should come on and you should hear sound at this point.
2. Test all functions of the installation for proper operation, and then reassemble the dash in
the reverse order of disassembly to complete the installation.
Note: To ensure that balance and faders are centered, turn volume up 3/4 and shut off vehicle
DO NOT shut off the radio, prior to shutting off the vehicle.
CONNECTIONS (CONT.) PROGRAMMING
AUDIO LEVEL ADJUSTMENTINSTALLATION


Product specificaties

Merk: AXESS
Categorie: Niet gecategoriseerd
Model: AXTO-TY1

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXTO-TY1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AXESS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd