AXESS AXTC-VW1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXTC-VW1 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
AXTC-VW1
I N S T A L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2023 METRA ELECTRONICS CORPORATION REV. 4/12/23 INSTAXTC-VW1
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections, especially the air
bag indicator lights, are plugged in before
reconnecting the battery or cycling the ignition
to test this product.
NOTE: Refer also to the instructions included
with the aftermarket accessory before
installing this device.
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties
TABLE OF CONTENTS
Connections 2 ............................................................
Programming 3 .........................................................
Troubleshooting.....................................................4
Volkswagen SWC (Steering Wheel Control)
and Data Interface 2002-2017
APPLICATIONS
• Provides accessory power
(10-amp)
• Provides wires for multimedia
radios (park brake, reverse,
speed sense)
• Used in both amplified and
non-amplified systems*
• Retains audio controls on the
steering wheel
• Designed to be compatible
with all major radio brands
• Auto detects vehicle type, radio
connection, and preset controls
• Ability to dual assign steering
wheel control buttons
• Retains memory settings even
after battery disconnection or
interface removal (non volatile
memory)
• Provides illumination output
• Micro-B USB updatable
Volkswagen
Beetle 2012-2015 ......................................
CC 2009-2017 ............................................
EOS 2007-2016 .........................................
Golf 2002(DDIN models only) ...................
Golf, Golf R 2003-2014 .............................
GTI 2002-2014 .........................................
Jetta 2002(DDIN models only) .................
Jetta, Jetta GLI 2003-2015 .......................
Jetta SportWagen 2010-2014 ..................
Passat.....................................2002-2015
R32 2007-2008 .......................................
Rabbit 2007-2009 ...................................
Tiguan 2009-2015 ....................................
• AXTC-VW1 interface
• AXTC-VW1 harness
• 3.5mm adapter
* Excluding Fender audio systems
Product Info
2
CONNECTIONS
Front
Rear
Sub
AUX-IN
Rear View
SWC
3.5mm Adapter (for vehicles without Steering wheel
controls or aftermarket radios with a wire for SWC)
Boss (with SWC wire): Key 1 (Gray) - Brown
Kenwood / JVC (with SWC wire): Blue/Yellow - Brown
XITE: SWC-2 - Brown
Key-A or SWC-1 - Brown
Key-B or SWC-2 - Brown/White
* After programming, assign SWC buttons within radio menu
Universal
Radio*
{
3.5mm Adapter for Vehicles without Steering wheel controls
1) 3.5mm adapter Brown Brown/White From the , tie the and wires together
with tape or connector
2) 3.5mm adapter AXTC-VW1 HarnessConnect the to the 3.5mm jack from the
3) AXTC-VW1 Program the per the instructions on page 3. Disregard steps 4 & 5
Black - Ground
Yellow - Battery power
Red - Accessory power
Orange - Illumination
Blue - Not used
Blue/White - Amp turn-on
Blue/Pink - VSS/Speed-Sense
Green/Purple - Reverse signal
Light Green - Parking brake
Gray - Front right speaker +
Gray/Black - Front right speaker -
White - Front left speaker +
White/Black - Front left speaker -
Green - Rear left speaker +
Green/Black - Rear left speaker -
Purple - Rear right speaker +
Purple/Black - Rear right speaker -
Aftermarket Radio
(radio’s features may vary)
Reset Button
LED Light
Vehicle Connector
Radio Connections
3
REV. 4/12/23 INSTAXTC-VW1
Open the driver’s door, and keep open during the programming process.
Cycle the ignition on.
Connect the to the , and then toAXTC-VW1 harness AXTC-VW1 interface
the wiring harness in the vehicle.
Locate the button on the the steering wheel. Program the Volume Up
interface by tapping the button at a heartbeat pace until the Volume Up
LED light stops flashing.
*Only applicable if vehicle came with steering wheel controls
The LED light will flash & while the interface programs Green Red
the radio to the steering wheel controls. Once programmed, the
LED light will go out, then produce a pattern which will identify the
radio type installed. Refer to the section under Radio LED Feedback
Troubleshooting for radio types.
*Only applicable if vehicle came with steering wheel controls
The LED light will go out, then once again quickly flash & Green Red
while the interface programs itself to the vehicle. Once programmed,
the LED light will go out again, then turn solid .Green
Cycle the ignition off, then back on.
Test all functions of the installation for proper operation.
Note: Audio Mode must be selected in the MFI menu to allow track up
and down to function. Refer to the vehicle owner’s manual for more
information.
PROGRAMMING
1.
2.
3.
4.*
5.*
6.
7.
8.
Gr Deen & Red LE
Gr Deen LE
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
VOL
+
Tap Volume Up
Gr Deen & Red LE
Gr Deen or Red LE


Product specificaties

Merk: AXESS
Categorie: Niet gecategoriseerd
Model: AXTC-VW1

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXTC-VW1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AXESS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd