AXESS AXSWC Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXSWC (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
AXSWC GENERAL INSTRUCTIONS
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 2/14/20 INSTAXSWC General Instructions
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties
TABLE OF CONTENTS
Installation Preparation ........................................2
Installation .............................................................2
Programming .........................................................3
Wire Description ....................................................3
AXSWC General Instructions
One interface does it all, no
additional interfaces needed
Designed to be compatible
with all major radio brands
Auto detects vehicle type, radio
connection, and preset controls
Ability to dual assign steering
wheel control buttons
Can be manually programmed
for most vehicles
Retains settings even after
battery disconnection or
interface removal
All connections done at the
radio location
Micro-B USB updatable
AXSWC Interface
AXSWC harness (12-pin harness with male 3.5mm jack)
3.5mm adapter
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date
vehicle specific applications
2
INSTALLATION PREPARATION INSTALLATION (CONT.)
From axxessinterfaces.com, submit the vehicle information in the box titled Vehicle Fit Guide &
AXSWC Install Instructions GET PARTS, then select . This will take you to a page where you will be
notified if your vehicle will work or not with the AXSWC interface. If the interface is compatible,
there will be a link under the green bar titled AXSWC **** Wiring Instructions. Click on this link
to open the PDF document for your specific vehicle. Print this document to have with you in the
vehicle during the installation.
Note: Though we have done extensive research, testing, and verifying that the steering wheel
control wires from the vehicles listed are correct, it is still the Installer’s responsibility to verify
that the steering wheel control wires are truly correct. If a discrepancy is found, please notify our
Tech Department at 386-257-1187, or techsupport@metra-autosound.com.
12-pin harness:
Connect the wire to chassis ground.Black
Connect the wire to the accessory power.Red
Locate the steering wheel control wire(s) in the vehicles harness as noted in the AXSWC
vehicle specific document. Connect this wire(s) to the AXSWC.
Note: Axxess recommends that the wires are soldered for the best “copper-to copper”
connection. Tapping style connectors are not recommended.
3.5mm jack:
Follow AXSWCH-PAR (sold separately) instructions.Parrot:
For the radios listed below: 3.5mm adapterConnect the , to the male 3.5mm SWC jack from
the AXSWC harness. Any remaining wires tape off and disregard.
Eclipse: Connect the steering wheel control wire, normally Brown Brown/White, to the
wire from the connector. Then connect the remaining steering wheel control wire,
normally , to the wire from the connector.Brown/White Brown
Metra OE: Connect the steering wheel control Key 1 wire to the wire.(Gray) Brown
Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow
wire to the wire.Brown
If the Note: Kenwood radio auto detects as a JVC, manually set the radio type to
Kenwood Changing Radio Type. See the instructions under .
Connect the steering wheel control SWC-2 wire from the radio to the wire.XITE: Brown
Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as
Key-A or SWC-1, to the Brown wire from the connector. Then connect the remaining
steering wheel control wire, referred to as Key-B or SWC-2, to the Brown/White wire
from the connector. If the radio comes with a third wire for ground, disregard this wire.
Note:
After the interface has been programmed to the vehicle, refer to the manual provided with
the radio for assigning the SWC buttons. Contact the radio manufacturer for more information
.
For all other radios: AXSWC harnessConnect the 3.5mm jack from the to the jack on the
radio designated for an external steering wheel control interface. Refer to the aftermarket
radios manual if in doubt as to where the 3.5mm jack goes to.
INSTALLATION
3
REV. 2/14/2020 INSTAXSWC GENERAL INSTRUCTIONS
Program the AXSWC as noted in the AXSWC vehicle specific document.
PROGRAMMING WIRE DESCRIPTION
1 Pink CAN-HI or Serial Data
2 White/Green Negative SWC
3 Yellow/Green Positive SWC
4 Green/Orange Negative SWC
5 Gray/Red Negative SWC
6 Black Chassis Ground
7 Blue/Pink CAN-LO
8 Black/Green Negative SWC
9 Red (skinny) Tip of 3.5 jack
10 White (skinny) Ring of 3.5 jack
11 Gray/Blue Negative SWC
12 Red Accessory Power
Pin Cavity Wire Color Input Description


Product specificaties

Merk: AXESS
Categorie: Niet gecategoriseerd
Model: AXSWC

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXSWC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AXESS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd