AXESS AXGMLN-01 Handleiding

AXESS Niet gecategoriseerd AXGMLN-01

Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXGMLN-01 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Installation instructions for part AXGMLN-01

REV. 8/6/2020 INSTAXGMLN-01

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake,

reverse, speed sense)

• Pre-wired AXSWC harness (AXSWC sold

separately)

• Retains chimes to the factory speaker

• Adjustable chime level

• Retains OnStar / OE Bluetooth

• Adjustable OnStar level

• Retains the factory backup camera

• Designed for non-amplified models, or

when bypassing a factory amp

• Retains balance and fade

• Includes an antenna adapter

• AXUSB-CBL updatable (sold separately)

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

• Small flat-blade screwdriver

TOOLS REQUIRED

AXGMLN-01

GM Data Interface

2006-Up

• AXGMLN-01 interface • AXGMLN-01 harness

• 16-pin harness with stripped leads • Backup camera harness • Antenna adapter

INTERFACE COMPONENTS

Connections to be made 2-3 ................................................

Installing the AXGMLN-01 3 ................................................

Initializing the AXGMLN-01 3 ..............................................

Adjusting the AXGMLN-01 4 ................................................

Table of Contents

APPLICATIONS

See inside front cover

AXGMLN-01

Applications

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the wire to the accessory wire.Red

Note: If installing an AXSWC (sold separately), there will be an accessory wire

there to connect as well.

• If the aftermarket radio has an illumination wire, connect the Orange/White

wire to it.

• If the aftermarket radio has a mute wire, connect the wire to it. If the Brown

mute wire is not connected, the radio will turn off when OnStar is activated.

• Connect the wire to the right front positive speaker output.Gray

• Connect the wire to the right front negative speaker output.Gray/Black

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

The following (3) wires are only for multimedia/navigation radios that require these wires

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wire.Light Green

Connections to be made

† These vehicles are standard for a factory amplifier. Either use the AXGMLN-02 interface,

or bypass the amplifier.

‡ Only for models without NAV in 2011-2015. For models with NAV, use the AXGMLN-08.

∆ Only for models without NAV in 2012-up. For models with NAV, use the AXGMLN-08.

BUICK

Enclave 2008-up

Lucerne 2006-2011

CADILLAC

DTS † 2006-2011

Escalade † 2007-2014

SRX † 2007-2009

CHEVROLET

Avalanche ∆ 2007-2013

Captiva Sport 2012-2015

Equinox 2007-2009

Express ‡ 2008-up

Impala 2006-2013

Impala Limited 2014-2016

Monte Carlo 2006-2007

Silverado (new body) ∆ 2007-2013

Silverado 2500/3500 ∆ 2014

Suburban ∆ 2007-2014

Tahoe ∆ 2007-2014

Traverse 2009-up

GMC

Acadia 2007-2016

Acadia Limited 2017

Savana ‡ 2008-up

Sierra 2500/3500 ∆ 2014

Sierra (new body) ∆ 2007-2013

Yukon / Yukon XL ∆ 2007-2014

HUMMER

H2 † 2008-2009

PONTIAC

Torrent 2007-2009

SATURN

Outlook 2007-2010

Vue 2008-2010

SUZUKI

XL-7 2007-2009

AXGMLN-01

Connections to be made

From the AXGMLN-01 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

• The Black/Yellow wire is used for OnStar level adjustment for models that

do not come equipped with steering wheel controls. See the OnStar level

Adjustment section for further instructions.

12-pin pre-wired AXSWC harness:

• This harness is to be used along with the optional AXSWC (not included)

to retain steering wheel audio controls. If the AXSWC is not being used,

disregard this harness. If it will be used, please refer to the AXSWC

instructions for radio connections and programming.

Note: Disregard the harness that comes with the AXSWC.

• Connect the wire to the accessory wire.Red

Note: The relay attached to the AXGMLN-01 harness is only for audible turn signal

clicks. No extra steps are required to retain this feature, so leave the relay as-is

Backup camera harness (if applicable):

• If retaining the factory backup camera, connect the Yellow RCA jack to the

backup camera input of the aftermarket radio.

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AXGMLN-01 harness,

into the interface.

• Connect the AXGMLN-01 harness to the wiring harness in the vehicle.

• If using the AXSWC, connect it after you initialize and test the AXGMLN-01, with

the key in the off position.

• If applicable, connect the backup camera harness to the wiring harness in the

vehicle. This harness is located behind the radio.

Attention! If the interface loses power for any reason, the following steps will need

to be performed again. Also, if installing an AXSWC connect it after you initialize and

test the interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

• Turn the key to the off position, pause for a moment, and then to the accessory

position. Test all functions of the installation for proper operation, before

reassembling the dash.

Installing the AXGMLN-01

Initializing the AXGMLN-01

Product specificaties

Merk:	AXESS
Categorie:	Niet gecategoriseerd
Model:	AXGMLN-01

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXGMLN-01 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd AXESS

AXESS AXBUCS-MZ286V Handleiding

9 September 2024

AXESS 99-7014HG Handleiding

29 Augustus 2024

AXESS AXGM-17 Handleiding

29 Augustus 2024

AXESS AXGMLN-34 Handleiding

29 Augustus 2024

AXESS 99-7382HG Handleiding

29 Augustus 2024

AXESS GMOS-12 Handleiding

29 Augustus 2024

AXESS XSVI-1788-NAV Handleiding

29 Augustus 2024

AXESS 99-7510HG Handleiding

29 Augustus 2024

AXESS AXBUCS-NI246V Handleiding

29 Augustus 2024

AXESS 99-3307G Handleiding

29 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024