AXESS AXDSPX-A2B3 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXDSPX-A2B3 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
AXDSPX-A2B3
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2024 METRA ELECTRONICS CORPORATION REV. 2/13/24 INSTAXDSPX-A2B3
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal before
installing this product. Ensure that all installation
connections, especially the air bag indicator lights,
are plugged in before reconnecting the battery or
cycling the ignition to test this product.
NOTE: Refer also to the instructions included with
the aftermarket radio.
INTERFACE FEATURES
INTERFACE COMPONENTS TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties
TABLE OF CONTENTS
Connections 2 ............................................................
Installation 3 .............................................................
LED Feedback 4 .........................................................
Lincoln Select Models 2018-Up A2B Data
Inter
face w/Amplifier Bypass Harness & DSP
• Designed for Revel A2B amplifiers
• A2B data interface w/AXDSP-X (digital signal processor) built-in
• Includes an amplifier bypass harness
• Retains factory chimes including parking sensor chimes
• Retains voice prompts
• Chimes and voice prompts go through the aftermarket amplifier
and/or cluster
• Selectable 31 Band graphic EQ or 5 Band Parametric EQ
• 10 individually assignable outputs
• AXDSPX-A2B3 interface
• AXDSPX-A2B3 harness
• LD-DSP-A2B-3
• LD-DSP-A2B-4
• AXDSPX-A2B3 interface harness
(male connectors: 12-pin, 16-pin)
• Amplifier bypass harness
(female connectors: 12-pin
black, 20-pin gray)
• AXBK-1
• A2B-EXT
For refer to . Enter the year, make, and model of the vehicle in theDash Disassembly Instructions, metraonline.com Vehicle Fit Guide for Radio Install kits.
Visit
axxessinterfaces.com
for current application list.
•
Settings adjusted via Bluetooth® in a smart device application (tablet
or mobile phone), compatible with both Android and Apple devices
• Independent equalization on each of the 10 outputs
• Independent high pass, low pass, and bandpass filters
•
Each channel can be delayed independently up to 10ms
• Clipping detection and limiting circuits
•
Read, write, and store configurations for future recall
• Password protect feature available in the mobile app
• Micro-B USB updatable
Google Play Store Apple App Store
iOS 12.1 or higher
Metraonline.com
2
CONNECTIONS TO BE MADE AT THE FACTORY AMPLIFIER’S LOCATION
Factory Amp
Factory Amp
(must be removed)
AXDSP-A2B3
Interface
AXBX-1
ass Harness
RCA Jacks
(sold separately)
AXBK-1
Blue/White - Amp Turn-On Wire
Red/White - Not Used
Factory Amplifier Locations
To Aftermarket
Amplifiers
Channel Programming
is done through the
AXDSP-XL App
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
Remote Bass Knob
Level Control for Ch5 and Ch6
LD-A2B-ADAPT
NOT USED
2 Harness Options*
A2B-EXT
Extension Cable
18-Pin
12-Pin
Right 2 input
Center input
Left 2 input
Right 1 input
Left 1 input
TBD
*Please see Speaker Assignment QR Code
located on the back page of instructions.
Please see Speaker
Assignment QR Code
located on the back
page of instructions.
*
Please see Speaker Assignment QR Code
located on the back page of instructions.
3
REV. 2/13/24 INSTAXDSPX-A2B3
INSTALLATION
1. Locate the factory amp, unplug all connectors, then remove the amp.
2. AXDSPX-A2B3 harness Install the and make all necessary connections, but leave the amp
turn-on wire disconnected.
Ensure the USB connector from the factory amp is connected to the AXDSPX-A2B3.Note:
3. AXDSPX-A2B3 harness Plug the 12-pin and 16-pin connectors from the into the
AXDSPX-A2B3 interface.
4. Google Play Store Apple App Store Download and install the AXDSP-XL app from the or .
5. Bluetooth Connection Open the app and follow the instructions on the tab to pair the
mobile device to the AXDSPX-A2B3. (Figure A)
6. Configuration Lock Down Scroll to the tab then select the vehicle type. Press the button to
save the configuration. (Figure B)
7. AXDSPX-A2B3 harness Connect the amp turn-on wire from the .
8. Identify Click the button to confirm that the AXDSPX-A2B3 is connected properly. If so, a
chime will be heard from the front left speaker or gauge cluster. Test all functions of the
installation for proper operation.
9. Setup Adjust the DSP settings in the app as desired. Refer to the instructions under the
Instructions tab, or online at Axxessinterfaces.com for an explanation of each tab in the app.
(Figure A)
(Figure B)


Product specificaties

Merk: AXESS
Categorie: Niet gecategoriseerd
Model: AXDSPX-A2B3

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXDSPX-A2B3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AXESS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd