AXESS AXDIS-HK3 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXDIS-HK3 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
AXDIS-HK3
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 12/19/22 INSTAXDIS-HK3
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
INTERFACE FEATURES
INTERFACE COMPONENTS
OPTIONAL ACCESSORIES
(sold separately)
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties • Small flat-blade screwdriver
TABLE OF CONTENTS
Connections .........................................................2-3
Installation .............................................................4
Programming .........................................................4
Audio Level Adjustment ........................................4
Steering Wheel Control Settings
- L.E.D. feedback ....................................................5
- Changing radio type ...........................................5
- Remapping the steering wheel control buttons 5-6
- Dual assignment instructions (long button press) .7-8
Troubleshooting .....................................................8
Hyundai/Kia Data Interface with SWC 2016-Up*
*2016 Nav models
Provides accessory power (12-
volt 10-amp)
Provides NAV outputs (park
brake, reverse, speed sense)
Retains audio controls on the
steering wheel
Designed for amplied‡ and
non-amplified models
Retains the factory AUX-IN jack
• Retains the factory backup camera
Includes an AXCSD-6V 12-to-6V
step-down for the factory camera
Retains balance and fade†
Micro-B USB updatable
• AXDIS-HK3 interface • AXDIS-HK3 harness
• AXCSD-6V • 16-pin harness with stripped leads
• Female 3.5mm connector with stripped leads
SPDIF Interface: AXSP-HK interface
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle
specific applications
‡ Requires the AXSP-HK (sold separately)
† Non-amplified models only
APPLICATIONS
See inside front cover
2
CONNECTIONSAPPLICATIONS
From the 16-pin harness with stripped leads to the aftermarket radio:
Connect the wire to the accessory wire.Red
If the vehicle comes equipped with a factory amplifier, connect the wire to the Blue/White
amp turn-on wire.
Connect the wire to the right front positive speaker output.Gray
Connect the Gray/Black wire to the right front negative speaker output.
Connect the wire to the left front positive speaker output.White
Connect the wire to the left front negative speaker output.White/Black
Connect the wire to the reverse wire, and also to the wire from Green/Purple Blue/White
the AXCSD-6V.
The following (1) wire is only for a multimedia/navigation radio that requires this wire.
Connect the wire to the parking brake wire.Light Green
Tape off and disregard the following (8) wires, they will not be used in this application:
Blue/Pink Blue/White* Brown Green Green/Black Orange/White Purple Purple/Black , , , , , , ,
* Non-amplified models only
From the AXDIS-HK3 harness to the aftermarket radio:
Connect the wire, the wire labeled “Camera Ground”, and also the wire Black Black Black
from the AXCSD-6V, to the ground wire.
Connect the wire labeled “Camera Power 6V”, to the wire from the Red Blue/Red AXCSD-6V
.
Connect the Yellow wire to the battery wire.
Connect the wire to the power antenna wire.Blue
If the aftermarket radio has an illumination wire, connect the Orange wire to it.
Hyundai
Accent 2018-up(1)
Elantra 2019-up(2)
Elantra 2017-2018(4)
Elantra GT 2018-up
Ioniq 2018-up(3)
Kona 2018-up
Santa Fe 2019-up
Santa Fe XL 2019-up
Sonata 2018-up
Sonata 2017(3)
Kia
Forte 2019-up
Forte / Forte 5 2017-2018 (4)
Optima 2019(5)
Rio / Rio 5 2018(1)
Sedona 2017-2018(4)
Sorento 2019
Soul 2017-2019(4)
(1) With Android Auto / Apple CarPlay radio
(2) With Android Auto / Apple CarPlay radio or NAV
(3) Without NAV
(4) With Android Auto / Apple CarPlay radio, without NAV
(5) With manual climate control
Continued on the next page
3
REV. 12/19/22 INSTAXDIS-HK3
CONNECTIONS (CONT.)
The following (1) wire is only for a multimedia/navigation radio that requires this wire.
Connect the wire to the VSS/speed sense wire.Blue/Pink
If the factory AUX-IN jack is desired to be retained, connect the & RCA jacks to the Red White
audio AUX-IN jacks.
Connect the Yellow RCA jack to the backup camera input.
For models equipped
without
a factory amplifier:
Connect the wire to the left rear positive speaker output.Green
Connect the wire to the left rear negative speaker output.Green/Black
Connect the wire to the right rear positive speaker output.Purple
Connect the wire to the right rear negative output.Purple/Black
Disregard the 14-pin connector, it will not be used in this application.
For models equipped
with
a factory amplifier:
Connect the AXSP-HK (sold separately) to the 14-pin connector.
Tape off and disregard the following (4) wires, they will not be used in this application:
Green Green/Black Purple Purple/Black, , ,
3.5mm jack steering wheel control retention:
The 3.5mm jack is to be used to retain audio controls on the steering wheel control.
For the radios listed below:
Connect the
female 3.5mm connector with stripped leads
, to the male
3.5mm SWC jack from the
AXDIS-HK3 harness
.
Any remaining wires tape off and disregard
.
Eclipse: Connect the steering wheel control wire, normally Brown Brown/White, to the
wire from the connector. Then connect the remaining steering wheel control wire,
normally Brown/White Brown, to the wire from the connector.
Metra OE: Connect the steering wheel control Key 1 wire to the wire.(Gray) Brown
Kenwood or select JVC with a steering wheel control wire: Blue/Yellow Connect the
wire to the wire.Brown
If the Note: Kenwood radio auto detects as a JVC, manually set the radio type to
Kenwood Changing Radio Type. See the instructions under .
Connect the steering wheel control SWC-2 wire from the radio to the XITE: Brown wire.
Parrot Asteroid Smart or Tablet:
Connect the 3.5mm jack to the AXSWCH-PAR (sold
separately). Then connect the 4-pin connector from the AXSWCH-PAR to the radio
.
The radio must be updated to rev. 2.1.4 or higher software.Note:
Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as
Key-A or SWC-1, to the wire from the connector. Then connect the remaining Brown
steering wheel control wire, referred to as Key-B or SWC-2, to the wire Brown/White
from the connector. If the radio comes with a third wire for ground, disregard this wire.
Note:
After the interface has been programmed to the vehicle, refer to the manual provided with
the radio for assigning the SWC buttons. Contact the radio manufacturer for more information
.
For all other radios: Connect the 3.5mm jack from the
AXDIS-HK3 harness
to the jack on
the radio designated for an external steering wheel control interface. Please refer to the
aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.


Product specificaties

Merk: AXESS
Categorie: Niet gecategoriseerd
Model: AXDIS-HK3

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXDIS-HK3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AXESS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd