AXESS AXDIS-GMLN31 Handleiding

AXESS Niet gecategoriseerd AXDIS-GMLN31

Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXDIS-GMLN31 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

AXDIS-GMLN31

I N S TA L L A T I O N I N S T R U C T I O N S

Product Info

INTERFACE FEATURES

INTERFACE COMPONENTS

TABLE OF CONTENTS

Connections to be made ....................................2-3

- 3.5mm jack steering wheel control retention 3 ..

Installing the AXDIS-GMLN31 .................................3

Programming the AXDIS-GMLN31 .........................4

Steering wheel control settings ........................5-7

- L.E.D. feedback ....................................................5

- Changing radio type ...........................................5

- Remapping the steering wheel control buttons ..6

- Dual assignment instructions ............................7

Troubleshooting .....................................................8

GM Data Interface with SWC 2019-Up

• Provides accessory power

(12-volt 10-amp)

• Retains R.A.P. (retained

accessory power)

• Provides NAV outputs (parking

brake, reverse, speed sense)

• Retains audio controls on the

steering wheel

•

Non-ampliﬁed models only

• Rearview camera retention

• Retains balance and fade

• Micro-B USB updatable

• AXDIS-GMLN31 interface • AXDIS-GMLN31 harness

• 16-pin harness with stripped leads

• Female 3.5mm connector with stripped leads

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.) • Small ﬂat-blade screwdriver

APPLICATIONS

Chevrolet

Camaro (IOR) *** † 2019-Up

Cheyenne (IOR) † 2019-2021

Colorado (IOR) 2019-Up

Cruze 2019-Up

Equinox (IOR) † 2019-Up

Malibu (IOR) † 2019-Up

Silverado (IOR) † 2019-2021

Sonic 2019-Up

Spark (IOR) 2019-Up

GMC

Canyon (IOR) 2019-Up

Sierra 1500 (IOR) † 2019-2021

Terrain (IOR) † 2019-Up

*** No Backup Camera Retention

† For extension, use AXEXH-GM31

CONNECTIONS TO BE MADE

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the wire to the accessory wire.Red

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange/White

• Connect the wire to the right front positive speaker output.Gray

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the Light Green wire to the parking brake wire

• Tape off and disregard the following (5) wires, they will not be used in this application:

Blue/White Green Green/Black Purple Purple/Black, , , and .

From the AXDIS-GMLN31 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

• Connect the Yellow RCA jack into the aftermarket radio’s ‘Rear Camera’ input.

Note:

The relay attached to the harness is only for audible turn signal clicks. No extra steps

are required to retain this feature, so leave the relay as-is.

Continue to 3.5mm jack steering wheel control retention

REV. 8/1/22 INSTAXDIS-GMLN31

3.5mm jack steering wheel control retention:

• The 3.5mm jack is to be used to retain audio controls on the steering wheel.

•

For the radios listed below, connect the included

female 3.5mm connector with stripped leads

to the

male 3.5mm SWC jack from the AXDIS-GMLN31 harness. Any remaining wires tape off and disregard

•

Eclipse: Connect the steering wheel control wire, normally Brown Brown/White, to the

wire of the connector. Then connect the remaining steering wheel control wire, normally

Brown/White, to the wire of the connectorBrown

•

Metra OE:

Connect the steering wheel control Key 1 wire

(Gray)

to the

Brown

wire.

•

Kenwood or select JVC with a steering wheel control wire:

Connect the

Blue/Yellow

wire

to the

Brown

wire.

Note:

If your Kenwood radio auto detects as a JVC, manually set the radio type to

Kenwood. See the instructions under changing radio type.

•

XITE:

Connect the steering wheel control SWC-2 wire from the radio to the

Brown

wire.

•

Parrot Asteroid Smart or Tablet:

Connect the 3.5mm jack into the AXSWCH-PAR (sold

separately), and then connect the 4-pin connector from the AXSWCH-PAR into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as Key-A

or SWC-1, to the

Brown

wire of the connector. Then connect the remaining steering wheel

control wire, referred to as Key-B or SWC-2, to the

Brown/White

wire of the connector. If the

radio comes with a third wire for ground, disregard this wire

Note:

After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio manufacturer

for more information.

• For all other radios: Connect the 3.5mm jack from the AXDIS-GMLN31 harness into the jack on

the aftermarket radio designated for an external steering wheel control interface. Please refer

to the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

CONNECTIONS TO BE MADE INSTALLING THE AXDIS-GMLN31(CONT)

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AXDIS-GMLN31 harness, into the

interface.

Attention!

Do not connect the AXDIS-GMLN31 harness to the wiring harness in the vehicle just yet

Attention!

If retaining steering wheel controls, ensure that the jack/wire is connected to the

radio before proceeding. If this step is skipped, the interface will need to be reset for the steering

wheel controls to function.

Product specificaties

Merk:	AXESS
Categorie:	Niet gecategoriseerd
Model:	AXDIS-GMLN31

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXDIS-GMLN31 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd AXESS

AXESS AXBUCS-MZ286V Handleiding

9 September 2024

AXESS 99-7014HG Handleiding

29 Augustus 2024

AXESS AXGM-17 Handleiding

29 Augustus 2024

AXESS AXGMLN-34 Handleiding

29 Augustus 2024

AXESS 99-7382HG Handleiding

29 Augustus 2024

AXESS GMOS-12 Handleiding

29 Augustus 2024

AXESS XSVI-1788-NAV Handleiding

29 Augustus 2024

AXESS 99-7510HG Handleiding

29 Augustus 2024

AXESS AXBUCS-NI246V Handleiding

29 Augustus 2024

AXESS 99-3307G Handleiding

29 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Vitec MGW Diamond-HX OG Handleiding

23 November 2024

Electrolux STA9 Handleiding

23 November 2024

Electrolux UMP3 Handleiding

23 November 2024

Electrolux ZS70GL Handleiding

23 November 2024

Bosch HEZ8TK36UC Handleiding

23 November 2024

Bosch HEZ8ZZ36UC Handleiding

23 November 2024

Bosch HDZIT301 Handleiding

23 November 2024

Bosch HEZBS301 Handleiding

23 November 2024

LG LX-330 Handleiding

23 November 2024

Stamos S-PLASMA 60U Handleiding

23 November 2024