AXESS AXDI-GLMLN29 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AXDI-GLMLN29 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Installation instructions for part AXDI-GLMLN29
REV. 1/20/2020 INSTAXDI-GLMLN29
axxessinterfaces.com metraonline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
Axxess Integrate
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
Provides accessory power (12-volt 10-amp)
Retains R.A.P. (retained accessory power)
Provides NAV outputs (parking brake, reverse, and speed sense)
Retains chimes through an onboard speaker
Pre-wired AXSWC harness (AXSWC sold separately)
Designed for non-amplified models, analog amplified models,
or when bypassing a factory amp
Retains balance and fade
Micro-B USB updatable
INTERFACE FEATURES
Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (i.e. butt-connectors, bell caps, etc.)
TOOLS REQUIRED
AXDI-GLMLN29
GM Data Interface
2006-Up
Connections to be made 2-3 ................................................
Installing the AXDI-GLMLN29 3 ...........................................
Initializing the AXDI-GLMLN29 3 .........................................
TABLE OF CONTENTS
INTERFACE COMPONENTS
AXDI-GLMLN29 interface • AXDI-GLMLN29 harness
APPLICATIONS
See application list inside cover
AXDI-GLMLN29
Connections to be madeApplication
From the AXDI-GLMLN29 harness to the aftermarket radio:
Connect the Black wire to the ground wire.
Connect the Yellow wire to the battery wire.
Connect the Red wire to the accessory wire.
Connect the Blue wire to the amp turn on wire.
If the aftermarket radio has an illumination wire, connect the wire to it.Orange
Connect the Gray wire to the right front positive speaker output.
Connect the Gray/Black wire to the right front negative speaker output.
Connect the White wire to the left front positive speaker output.
Connect the White/Black wire to the left front negative speaker output.
Connect the Green wire to the left rear positive speaker output.
Connect the Green/Black wire to the left rear negative speaker output.
Connect the Purple wire to the right rear positive speaker output.
Connect the Purple/Black wire to the right rear negative speaker output.
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the Blue/Pink wire to the VSS/speed sense wire.
Connect the Green/Purple wire to the reverse wire.
Connect the Light Green wire to the parking brake wire.
BUICK
Enclave 2008-up
Lucerne 2006-2011
CADILLAC
DTS 2006-2011 †
Escalade, Escalade ESV
& EXT 2007-2011 †
SRX 2007-2009 †
CHEVROLET
Avalanche
(without RPO code STZ
or Y91) * 2007-2013
Captiva Sport 2012-2015
Equinox 2007-2009
Express 2008-up ‡
Impala 2006-2013
Impala Limited 2014-2016
Monte Carlo 2006-2007
Silverado (new body)
(without RPO code Y91) *
2007-2013
Silverado 2500/3500
(without RPO code Y91)
*
2014
Suburban (without RPO
code STZ or Y91) *
2007-2014
Tahoe (without RPO code
STZ or Y91) * 2007-2014
Traverse 2009-up
GMC
Acadia 2007-2016
Acadia Limited 2017
Savana 2008-up ‡
Sierra 2500/3500
(without RPO code Y91) *
2014
Sierra (new body)
(without RPO code Y91) *
2007-2013
Yukon (without RPO code
STZ or Y91) * 2007-2014
Yukon XL (without RPO
code STZ or Y91) *
2007-2014
HUMMER
H2 2008-2009 †
PONTIAC
Torrent 2007-2009
SATURN
Outlook 2007-2010
Vue 2008-2010
SUZUKI
XL-7 2007-2009
* These vehicles have a digital amp option. Please reference the “Service Parts
Identification” sticker located in the glove box for the RPO code listed. If the RPO code
listed is present, the vehicle is equipped with a digital amplifier. Either use the
AXDIS-GMLN29 interface, or bypass the amp.
These vehicles are standard for a digital amplifier. Either use the AXDIS-GMLN29 interface,
or bypass the amp.
Only for models without NAV in 2011-2015 Only for models without NAV in 2012-Up.Continued on the next page
AXDI-GLMLN29
Connections to be made (Cont) Installing the AXDI-GLMLN29
Initializing the AXDI-GLMLN29
With the key in the off position:
• Connect the AXDI-GLMLN29 harness into the interface, and then to the wiring
harness in the vehicle.
Note: If using the AXSWC, connect it after you initialize and test the AXDI-
GLMLN29, with the key in the off position.
Attention! If the interface loses power for any reason, the following steps will need
to be performed again. Also, if installing an AXSWC connect it after you initialize and
test the interface/radio, with the key in the off position.
• Turn the key (or push-to-start button) to the ignition position and wait until the
radio comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the
off position, disconnect the interface, check all connections, reconnect the
interface, and then try again.
• Turn the key to the off position, and then to the accessory position. Test all
functions of the installation for proper operation, before reassembling the dash.
12-pin pre-wired AXSWC harness:
This harness is to be used along with the optional AXSWC (not included) to
retain steering wheel audio controls. If the AXSWC is not being used, disregard
this harness. If it will be used, please refer to the AXSWC instructions for radio
connections and programming.
Note: Disregard the harness that comes with the AXSWC.


Product specificaties

Merk: AXESS
Categorie: Niet gecategoriseerd
Model: AXDI-GLMLN29

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AXDI-GLMLN29 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd AXESS

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd