AXESS AX-ADGM04 Handleiding

AXESS Niet gecategoriseerd AX-ADGM04

Lees hieronder de 📖 handleiding in het Nederlandse voor AXESS AX-ADGM04 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-ADGM04

I N S TA L L A T I O N I N S T R U C T I O N S

INTRODUCTION

INTERFACE FEATURES

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder,

and heat shrink • Small ﬂat-blade screwdriver

• Tape

• Wire cutter • Zip ties

TABLE OF CONTENTS

Connections to be made

For models

without

an ampliﬁer .......................3

For models

with

an analog ampliﬁer ................4

For models

with

a digital ampliﬁer ...................5

12-pin pre-wired ASWC-1 harness ......................6

DIN jack ................................................................6

Installing & programming the AX-ADGM04

AX-ADBOX1 ...........................................................6

AX-ADBOX2 .......................................................... 7

Adjusting the AX-ADGM04 ....................................8

Extra features .........................................................9

GM Data Interface 2012-2016

APPLICATIONS

See inside front cover

The AX-ADGM04 harness is designed for, and must be used with, the

AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the

AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads

• Provides accessory power (12-volt 10-amp)

• Maintains the retained accessory power

(R.A.P.) feature

• Provides NAV outputs (parking brake,

reverse, speed sense)

• Retains chimes

• Retains OnStar / OE Bluetooth

• Adjustable OnStar level

• Retains RSE (rear seat entertainment)

• Retains satellite radio

• Retains the factory AUX-IN jack

• Pre-wired ASWC-1 harness

(ASWC-1 sold separately)

• Can be used in non-ampliﬁed, or analog/

digital ampliﬁed models

• Retains balance and fade†

• Micro-B USB updatable

INTERFACE COMPONENTS

• AX-ADGM04 harness

• 4-pin to 4-pin resistor pad harness

† To retain fade in digital ampliﬁed models, use the AX-ADBOX1

APPLICATIONS

CHEVROLET

Avalanche † * 2012-2013

Express † 2013-2015

Malibu

(with monochrome display) 2013-2015

Malibu Limited

(with monochrome display) 2016

CHEVROLET (CONT)

Silverado 2500 / 3500 † * 2014

Silverado † * 2012-2013

Suburban † ** 2012-2014

Tahoe † ** 2012-2014

Trax 2015-2016

GMC

Savana † 2013-2015

Sierra 2500 / 3500 † * 2014

Sierra † * 2012-2013

Yukon / Yukon XL † ** 2012-2014

These vehicles have a digital amp option. Please reference the “Service Parts Identiﬁcation” sticker located in the glove box for the RPO code Y91. If Y91 is present, then the vehicle is equipped with a digital ampliﬁer

These vehicles have a digital amp option. Please reference the “Service Parts Identiﬁcation” sticker located in the glove box for the RPO code Y91, STZ, or UQS. If Y91, STZ, or UQS is present, then the vehicle is equipped with a

digital ampliﬁer

† Only for models equipped with NAV. If not equipped with NAV, use the AX-ADGM01.

REV. 5/4/2020 INSTAX-ADGM04

From the AX-ADGM04 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) wires to Red

accessory power.

• Cut off the resistors from the Green Green/Black Purple Purple/Black, , , and wires below the

heat shrink.

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

• Ensure the (2) 4-pin Molex connectors are connected together.

Note: The 4-pin to 4-pin resistor pad harness will not be used in this application.

• The Black/Yellow wire is used for OnStar level adjustment for models that do not come

equipped with steering wheel controls. Refer to the OnStar level Adjustment section for

further instructions.

• Connect the and RCA jacks to the audio AUX-IN jacks from the aftermarket radio.Red White

• Disregard the wire with a red connector, it will not be used in this application.Pink

Note: The relay attached to the AX-ADGM04 harness is only for audible turn signal clicks.

No extra steps are required to retain this feature, so leave the relay as-is.

Continue to 12-pin pre-wired ASWC-1 harness

CONNECTIONS TO BE MADE

Attention! This interface will work with models that are either non-ampliﬁed, analog ampliﬁed,

or digital ampliﬁed. Please follow the instructions carefully for your model vehicle. Failure to

do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory

ampliﬁed or not, please contact your local dealership.

For models

without

an ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):

• Connect the wire to the accessory wire.Red

Note: If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) Red

wires on the AX-ADGM04 harness as well.

• Connect the wire to the power antenna wire.Blue/White

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

• If the aftermarket radio has a mute wire, connect the wire to it. If the mute wire is Brown

not connected, the radio will turn off when OnStar is activated.

• Connect the wire to the right front positive speaker output.Gray

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wireLight Green

• Tape off and disregard the following (4) wires, they will not be used in this application:

Green Green/Black Purple Purple/Black, , ,

Product specificaties

Merk:	AXESS
Categorie:	Niet gecategoriseerd
Model:	AX-ADGM04

Heb je hulp nodig?

Als je hulp nodig hebt met AXESS AX-ADGM04 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd AXESS

AXESS AXBUCS-MZ286V Handleiding

9 September 2024

AXESS 99-7014HG Handleiding

29 Augustus 2024

AXESS AXGM-17 Handleiding

29 Augustus 2024

AXESS AXGMLN-34 Handleiding

29 Augustus 2024

AXESS 99-7382HG Handleiding

29 Augustus 2024

AXESS GMOS-12 Handleiding

29 Augustus 2024

AXESS XSVI-1788-NAV Handleiding

29 Augustus 2024

AXESS 99-7510HG Handleiding

29 Augustus 2024

AXESS AXBUCS-NI246V Handleiding

29 Augustus 2024

AXESS 99-3307G Handleiding

29 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024