AV:link M8S Handleiding

AV:link Subwoofer M8S

Lees hieronder de 📖 handleiding in het Nederlandse voor AV:link M8S (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

M8S

ACTIVE SUBWOOFER 8”

Order ref: 170.190UK

User Manual

Version 1.1

Caution: Please read this manual carefully before operating

Damage caused by misuse is not covered by the warranty

170.190 User Manual UK

Introduction

Thank you for choosing the AV Link M8S active subwoofer as part of your sound system. This product is designed with

flexibility and reliability in mind to offer long-lasting, high quality output for many varied applications. Please read this

manual fully and follow the instructions to achieve the best results with your new purchase and to avoid damage through

misuse.

Warning

To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.

If liquids are spilled on the cabinet, stop using immediately, allow unit to dry out and have checked by qualified personnel

before further use. Avoid impact, stress or extreme pressure to the cabinet

No user serviceable parts inside Do not open the panel refer all servicing to qualified service personnel – –

Safety

• Check for correct mains voltage and condition of Fig.8 lead before connecting to power outlet

• Ensure speaker wires and/or signal leads are in good condition with no shorts or damaged plugs

• Do not allow any foreign objects to enter the case or through the ventilation grilles

Placement

• Keep out of direct sunlight and away from heat sources

• Avoid damp or dusty environments

• Position on a level, stable surface, ideally against a wall or in a corner

• Avoid sharp objects protruding through the front grille cloth or speaker cone

• Ensure adequate access to controls and connections

Cleaning

• Use a soft dry or slightly damp cloth to clean the cabinet as required

• Use a vacuum cleaner to clear the rear heat-sink of any dust or debris build-ups

• Do not use strong solvents for cleaning the unit

Amplifier Panel

1. Amplifier “HI LEVEL” inputs

Connect and wires tween + - be

amplifier L+R outputs and speakers

2. RCA L+R LINE IN

L+R inputs for line level audio signal

3. POWER LED

Indicates mains power on

4. FREQ control

Adjust cutoff frequency of crossover

5. VOLUME level control

Adjust overall output of subwoofer

6. Mains fuse holder

Replace only with approved type

7. Fig.8 Mains inlet

Connect supplied mains lead here

8. Power switch

Switches mains power ON/OFF

9. AUTO ON/ON

Select “Auto on” or “Always on”

170.190 User Manual UK

Connection

Connect the M8S to the mains using the mains lead supplied or an equivalent, good quality fig.8 mains lead.

Ensure that the mains voltage is as stated on the rear panel and the outlet has sufficient capacity to operate the sub.

Determine how the sub unit is to be configured. If already operating a stereo amplifier with 2 speakers, the M8S can be

configured to “tap off” a signal from the amplifier output without affecting the power output of the left and right

speakers.

Simply connecting the Left and Right amplifier outputs to the “AMPLIFIER HI LEVEL IN” terminals on the M8S and then

from these terminals onto the left and right speakers effectively connects the M8S between the amplifier and speakers,

which can simplify wiring, removing the need for a separate signal lead to the sub unit.

Alternatively, if a separate line level audio signal is available, connecting left and right RCA cables to the “LINE IN”

connectors is preferred (left and right signals are fed independently to the speaker and are not electrically summed)

With the VOLUME control turned fully down, switch on the power on the rear panel Once powered up, gradually turn the .

VOLUME up part way and play a signal through the system. Increase VOLUME as required to balance with top speakers.

Rotating the FREQ control will vary the cutoff frequency of the internal active crossover circuit. The ideal setting depends

upon the program material, types of top speakers used and personal preference. Lower settings may require higher

VOLUME adjustment to compensate for the extra frequencies that are removed from the signal.

Take care not to drive the sub unit too hard (usually denoted by a “knocking” or “flapping” noise from the speaker cone).

Sub bass is difficult to hear over full range speakers and should be almost imperceptible in operation, simply adding

warmth and fullness to the sound.

At the lower right- hand side of the rear panel is a selector switch marked “AUTO ON – ON”

Selecting AUTO ON puts the M8S into an energy saving standby mode when no signal is present and automatically

switches power to the amplifier when a signal is detected.

Selecting ON keeps the amplifier powered up constantly.

The front grille frame is removable for studio monitor applications or where the speaker cone may not need protecting.

Before powering down, turn the channel gain controls fully down to avoid loud noises when switching off.

Specifications

M8S Subwoofer

Power supply

220 - 250Vac, 50/60Hz, Fig.8

Driver

20cm (8“) reinforced cone

Connections

Speaker level input terminals, RCA line level in

Cutoff frequency

45 - 150Hz

Rated output power

100W

Peak output

200W

Frequency response

50 - 250Hz

Dimensions

300 x 330 x 300mm

Weight

7.44kg

Product specificaties

Merk:	AV:link
Categorie:	Subwoofer
Model:	M8S
Kleur van het product:	Zwart
Gebruikershandleiding:	Ja
Impedantie:	4 Ohm
Gemiddeld vermogen subwoofer:	100 W
Diameter driver subwoofer (imperiaal):	8 "
Subwoofertype:	Actieve subwoofer
Frequentiebereik subwoofer:	50 - 250 Hz
Breedte van de subwoofer:	300 mm
Hoogte van de subwoofer:	300 mm
Diepte van de subwoofer:	330 mm
Gewicht subwoofer:	7440 g
AC-ingangsspanning:	220-250 V
AC-ingangsfrequentie:	50/60 Hz
Diameter driver subwoofer:	200 mm
Subwoofer maximale vermogen:	200 W
Crossover subwoofer frequenties:	45 - 150 Hz