Audiovox Code Alarm ASCL6 CarLink Handleiding

Audiovox Afstandsbediening Code Alarm ASCL6 CarLink

Lees hieronder de 📖 handleiding in het Nederlandse voor Audiovox Code Alarm ASCL6 CarLink (73 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/73
EN-20190222-A
This system must be installed by a professional.
NOTICE
The manufacturer will accept no responsability for any electrical damage resulng from
improper installaon of this product, be that either damage to the vehicle itself or to the
installed device. This device must be installed by a cered technician. Please review the
Installaon Guide carefully before beginning any work.
COMPLETE INSTALLATION & PROGRAMMING GUIDE
Telematics Communicator System
HARDWARE PARTS 3 ................................................................................................................................
iDATASTART HCx 4 .....................................................................................................................................
iDATASTART VWx .................................................................................................................................... 6
iDATASTART BM or BZ 8 ..........................................................................................................................
AKX or OEM 10 .............................................................................................................................................
ADS-AL-CA / OL-MDB-ALL 12 ................................................................................................................
FLASHLOGIC FL-CAN 14 ...........................................................................................................................
CRIMESTOPPER 16 ......................................................................................................................................
FLASHLOGIC FLRS 18 ................................................................................................................................
FLASHLOGIC FLRSBA 20 ........................................................................................................................
FLASHLOGIC FLCMVW 22 .......................................................................................................................
COMPUSTAR CM7000 / CM7200 / POLARSTART PRS-16 ...................................................24
COMPUSTAR CM6200 26 .........................................................................................................................
COMPUSTAR DC2 28 ..................................................................................................................................
COMPUSTAR DC3 30 .................................................................................................................................
POLARSTART PRS-13 32 ...........................................................................................................................
DIRECTED DBALL 2 34 ..............................................................................................................................
DIRECTED DB3 36 .......................................................................................................................................
DIRECTED 4X10 - 5X10 - AF-D600 - ASD200 - ASD-600 38 ....................................................
DIRECTED DS4 - DS4+ 40 .......................................................................................................................
FORTIN EVO-ALL 42 ..................................................................................................................................
FORTIN EVO-ONE 44 ................................................................................................................................
PRESTIGE (E) Models 46 ..........................................................................................................................
PRESTIGE (Z) Models 48 ..........................................................................................................................
PURSUIT (E) Models 50 ............................................................................................................................
CODE SYSTEMS ......................................................................................................................................52
OLDER CODE SYSTEMS......................................................................................................................54
OMEGA RS-X70 56 ......................................................................................................................................
OMEGA AL-XX70-B 58 ..............................................................................................................................
DSE 503AIR 5R-85 60 ...............................................................................................................................
DSE iSTART2 - 3 62 .....................................................................................................................................
LED Status Reference Chart 64 .............................................................................................................
RESET PROCEDURE 64 ............................................................................................................................
2
TABLE OF CONTENTS
HRN-MCAR-01
HRN-LLRS-01
HRN-DRS-02
FLCL6HAR, OL-HRN-LINKR-ALL
(Sold Separately)
OL-ADAPTER-B2G
This Adapter is supplied ONLY inside
the Linkr LT boxes.
OL-ADAPTER-B2G
HARDWARE PARTS
AR-3HU / VS-4LU
CREATE AN ACCOUNT
Before begining the installation and setting the configurations of a CL6 unit, we strongly
recommend downloading the Application from the App store and create a user account.
a. Go to the App store (Apple) or Play store (Android) and Search for “CL6”. Download and install
the Free Application.
b. Launch the newly installed CL6 Application on your smartphone or tablet
c. Click “Create an Account”
d. Fill in all the required fields
e. Once completed, click “Create your Account”
f. Open your Email and look for a new email sent from “MYCARCONTROLS”
g. To activate your account and create your secure password, click the embedded link in the email.
h. Create your secure password and activate your account.
i. Once done, Log into the Application using your email and your newly created password.
4
PARTS REQUIRED FOR INSTALLATION OF : iDATASTART HCx
Telematics device HRN-MCAR-01 iDatastart HCx
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the iDatastart HCx remote starter to
accept the telematic device. When flashing the iDatastart HCx remote starter, please ensure to turn ON the
Telematics option from the telematics section and choose “MyCar”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics device
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the iDatastart HCx remote
starter previously installed, you must set the protocol to ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
6
PARTS REQUIRED FOR INSTALLATION OF : iDATASTART VWx
Telematics device HRN-MCAR-01 iDatastart VWx
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the iDatastart VWx remote starter to
accept the telematic device. When flashing the iDatastart VWx remote starter, please ensure to turn ON
the Telematics option from the telematics section and choose “MyCar”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics devic
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the iDatastart VW remote
starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
8
PARTS REQUIRED FOR INSTALLATION OF : iDATASTART BM or BZ
Telematics device HRN-MCAR-01 iDatastart BM or BZ
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the iDatastart BM or BZ remote starter
to accept the telematic device. When ashing the iDatastart BM or BZ remote starter, please ensure to
choose the “MyCar” telematics protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the iDatastart BM or BZ
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
10
PARTS REQUIRED FOR INSTALLATION OF : AKX or OEM
Telematics device HRN-MCAR-01 AKX or OEM
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the AKX or OEM remote starter to accept
the telematic device. When ashing the AKX or OEM remote starter, please ensure to choose the “MyCar”
telematics protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the AKX or OEM remote
starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
12
PARTS REQUIRED FOR INSTALLATION OF : ADS-AL-CA / OL-MDB-ALL
Telematics device HRN-MCAR-01 ADS-AL-CA / OL-MDB-ALL FLCL6HAR,
OL-HRN-LINKR-ALL
(sold Separately)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the ADS-AL-CA or OL-MDB-ALL remote
starter to accept the MyCar telematics device. When ashing the ADS-AL-CA or OL-MDB-ALL remote start-
er, please ensure to choose the “MyCar” telematics protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
FLCL6HAR
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the device (SN: XXXXXX-XXXXXXXXXX) and
Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly in-
stalled device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the MyCar device. When combined with the ADS-AL-CA or OL-MDB-
ALL remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then
click “Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the MyCar device to update your protocol selection
and reboot. After this wait period it will be available to accept commands from the App. In the vehicle
control screen, the Device Signal icon located above the Stop button will display the connectivity status
of your MyCar device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is Green, Device
is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to dis-
play in the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the MyCar Owners Card is handed to the New Owner of the vehicle. Doing this will
ensure that the instructions on how to setup their App, Account and Vehicle is done correctly by using the
device serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
14
PARTS REQUIRED FOR INSTALLATION OF : FLASHLOGIC FL-CAN
Telematics device HRN-MCAR-01 Flashlogic FL-CAN FLCL6HAR
(sold Separately)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the Flashlogic FL-CAN remote starter to ac-
cept the MyCar telematics device. When ashing the Flashlogic FL-CAN remote starter, please ensure to
choose the “ASCL6” telematics protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
FLCL6HAR
INSTALLATION, WIRING & PROGRAMMING GUIDE
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
FLCL6HAR
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the device (SN: XXXXXX-XXXXXXXXXX) and
Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly in-
stalled device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the MyCar device. When combined with the Flashlogic FL-CAN
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the MyCar device to update your protocol selection
and reboot. After this wait period it will be available to accept commands from the App. In the vehicle
control screen, the Device Signal icon located above the Stop button will display the connectivity status
of your MyCar device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is Green, Device
is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to dis-
play in the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the MyCar Owners Card is handed to the New Owner of the vehicle. Doing this will
ensure that the instructions on how to setup their App, Account and Vehicle is done correctly by using the
device serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
16
PARTS REQUIRED FOR INSTALLATION OF : CRIMESTOPPER
Telematics device HRN-MCAR-01 CrimeStopper HRN-LLRS-01
STEP 1. CONFIGURE THE REMOTE STARTER
The CrimeStopper remote starter must be congured to accept the telematics device. When programming
the CrimeStopper remote starter, please ensure to select the option indicated “Smart Phone Baud Rate”.
This option MUST BE SET TO 9600baud.
1- Disconnect the HRN-LLRS-01 white connector from Crimestopper Remote Starter
2- Go in the Crimestopper programming and set Baud rate to 9600.
3- Shut ignition O and Disconnect Power from the Crimestopper RS.
5- Wait 10 seconds. Then Reconnect RS and the HRN-LLRS-01 harness for the MyCar.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
Compatible models:
RS-00, RSx-G5, SP402, SP502
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-LLRS-01
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the CrimeStopper remote
starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
CRIMESTOPPER TROUBLESHOOTING
While testing the system, if you are unsuccessful at operating the Remote Starter using the telematic
system it is probably related to the Baud rate not being set correctly as described in Step 1. To overcome
this situation, please follow these steps.
1- Disconnect HRN-LLRS-01 white connector from Crimestopper Remote Starter.
2- Go in Crimestopper RS programming and set back the Baud rate to 115200.
3- Then inside the programming go to Reset all to default (following option right after the Baud Rate).
4- Shut ignition O and Disconnect Power from the Crimestopper RS.
5- Wait 10 seconds. Then Reconnect Crimestopper RS only. DO NOT RECONNECT the telematics device yet.
6- Go back in the Crimestopper RS programming and set Baud rate to 9600.
7 - Shut ignition O and Disconnect Power from the Crimestopper RS.
8- Wait 10 seconds. Then Reconnect Crimestopper RS and HRN-LLRS-01 harness for the telematic device.
9- Wait for the telematic device to be Online (Battery Status and Signal Green).
10- Send a Lock or Unlock command. Parking lights will click in the Crimestopper RS.
11- Then complete all other required programming in the Crimestopper RS.
INSTALLATION, WIRING & PROGRAMMING GUIDE
18
PARTS REQUIRED FOR INSTALLATION OF : FLASHLOGIC FLRS
Telematics device HRN-MCAR-01 Flashlogic FLRS
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the Flashlogic FLRS remote starter to ac-
cept the telematic device. When ashing the Flashlogic FLRS remote starter, please ensure to choose the
ASCL6” telematics protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Flashlogic FLRS
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
20
PARTS REQUIRED FOR INSTALLATION OF : FLASHLOGIC FLRSBA
Telematics device HRN-MCAR-01 Flashlogic FLRSBA
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the Flashlogic FLRSBA remote starter to
accept the telematic device. When ashing the Flashogic FLRSBA remote starter, please ensure to turn ON
the Telematics option from the telematics section and choose “Carlink”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics devic
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Flashlogic FLRSBA
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
22
PARTS REQUIRED FOR INSTALLATION OF : FLASHLOGIC FLCMVW
Telematics device HRN-MCAR-01 Flashlogic FLCMVW
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the Flashlogic FLCMVW remote starter to
accept the telematic device. When ashing the Flashlogic FLCMVW remote starter, please ensure to turn
ON the Telematics option from the telematics section and choose “Carlink”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics devic
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Flashlogic FLCMVW
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
24
PARTS REQUIRED FOR INSTALLATION OF : COMPUSTAR CM7000 / CM7200 /
POLARSTART PRS-16
Telematics device HRN-MCAR-01 CM7000 / CM7200 / PRS-16 BLADE-AL (64)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the Compustar or Polarstart remote starter
to accept the telematic device. When flashing the Compustar or Polarstart remote starter, please ensure
the remote starter firmware and BLADE-AL (64) firmwares are updated to the latest firmware available.
Then set the Option Group #4 “DroneMobile or Fortin Gray 4pin” to DR-2000 and Flash remote starter.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics device
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery
(RED)
Ground
(BLACK)
Data
(WHITE)
Data
(BLUE)
Alarm(+)
(YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Compustar or
Polarstart remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT”
then click “Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
26
PARTS REQUIRED FOR INSTALLATION OF : COMPUSTAR CM6200
Telematics device HRN-MCAR-01 Compustar CM6200 BLADE-AL (64)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the Compustar remote starter to accept the
telematic device. When flashing the Compustar remote starter, please ensure the remote starter firmware
and BLADE-AL (64) firmwares are updated to the latest firmware available.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics device
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Compustar remote
starter previously installed, you must set the protocol to ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
28
PARTS REQUIRED FOR INSTALLATION OF : COMPUSTAR DC2
Telematics device HRN-MCAR-01 Compustar DC2
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the Compustar DC2 remote starter to accept
the telematic device. When flashing the Compustar DC2 remote starter, please ensure to turn ON the Tele-
matics option from the telematics section and choose “Drone Mobile”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics device
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Compustar DC2
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
30
PARTS REQUIRED FOR INSTALLATION OF : COMPUSTAR DC3
Telematics device HRN-MCAR-01 Compustar DC3
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the Compustar DC3 remote starter to accept
the telematic device. When flashing the Compustar DC3 remote starter, please ensure to turn ON the Tele-
matics option from the telematics section and choose “Drone Mobile”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics device
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Compustar DC3
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
32
PARTS REQUIRED FOR INSTALLATION OF : POLARSTART PRS-13
Telematics device HRN-MCAR-01 PRS-13 BLADE-AL (64)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the Polarstart PRS-13 remote starter to ac-
cept the telematic device. When flashing the Polarstart PRS-13 remote starter, please ensure the remote
starter firmware and BLADE-AL (64) firmwares are updated to the latest firmware available. Then ensure
to set the Option Group #4 “DroneMobile or Fortin Gray 4pin” to DR-2000 and Flash remote starter.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics device
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Polarstart PRS-13
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
34
PARTS REQUIRED FOR INSTALLATION OF : DIRECTED DBALL 2
Telematics device HRN-MCAR-01 DBALL2 HRN-DRS-01 or
HRN-DRS-02
STEP 1. CONFIGURE THE REMOTE STARTER
The Directed XKloader 2 or 3 is required to properly configure the DBALL2 remote starter to accept the
telematic device. When flashing the DBALL2 remote starter, please ensure to choose the “Smartstart”
telematic protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics device
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
DBALL 2
HRN-DRS-02
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the DBALL2 remote
starter previously installed, you must set the protocol to “DEI” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
36
PARTS REQUIRED FOR INSTALLATION OF : DIRECTED DB3
Telematics device HRN-MCAR-01 DB3 HRN-DRS-01 or
HRN-DRS-02
STEP 1. CONFIGURE THE REMOTE STARTER
The Directed XKloader 2 or 3 is required to properly configure the DB3 remote starter to accept the tele-
matic device. When flashing the DB3 remote starter, please ensure to choose the “Smartstart” telematic
protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics device
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-DRS-02
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the DB3 remote starter
previously installed, you must set the protocol to “DEI” and click “ACCEPT” then click “Done” at the top
right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
38
PARTS REQUIRED FOR INSTALLATION OF : DIRECTED 4X10 - 5X10 - AF-
D600 - ASD200 - ASD-600
Telematics device HRN-MCAR-01 4X10 - 5X10 - AF-D600
ASD200 - ASD600
HRN-DRS-01 or
HRN-DRS-02
STEP 1. CONFIGURE THE REMOTE STARTER
The Directed XKloader 2 or 3 is required to properly congure the 4X10 - 5X10 - AF-D600 - ASD200 - ASD-
600 remote starter to accept the telematic device. When ashing the 4X10 - 5X10 - AF-D600 - ASD200 -
ASD-600 remote starter, please ensure to choose the “Smartstart” telematic protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-DRS-02
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the 4X10 - 5X10 - AF-
D600 - ASD200 - ASD-600 remote starter previously installed, you must set the protocol to “DEI” and
click “ACCEPT” then click “Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
40
PARTS REQUIRED FOR INSTALLATION OF : DIRECTED DS4 - DS4+
Telematics device HRN-MCAR-01 DS4 / DS4+ HRN-DRS-01 or
HRN-DRS-02
STEP 1. CONFIGURE THE REMOTE STARTER
The Directed XKloader 2 or 3 is required to properly congure the DS4 / DS4+ remote starter to accept the
telematic device. When ashing the DS4 / DS4+ remote starter, please ensure to choose the “Smartstart
telematic protocol.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-DRS-02
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the DS4 / DS4+ remote
starter previously installed, you must set the protocol to “DEI” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
42
PARTS REQUIRED FOR INSTALLATION OF : FORTIN EVO-ALL
Telematics device HRN-MCAR-01 EVO-ALL HRN-LLRS-01
STEP 1. CONFIGURE THE REMOTE STARTER
The Fortin Flashlink is required to properly congure the EVO-ALL remote starter to accept the telematics
device. When ashing the EVO-ALL remote starter, please ensure to choose the following options:
- C1 - OEM Remote starter
- D1 - 3x Lock start
- H2 - Fortin 2
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-LLRS-01
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Evo-All remote starter
previously installed, you must set the protocol to “Fortin” and click “ACCEPT” then click “Done” at the
top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. LEARN THE TELEMATIC DEVICE TO THE EVO-ALL
In order to communicate with the remote starter, the Telematic device must be learned to the EVO-ALL.
1- Disconnect the Black 4 pin power connector from the Evo-All.
2- Press and Hold the Programming button on the Evo-All while plugging back the Black 4 pin connector.
3- The LED’s on the Evo-All will begin to cycle. Keep pressing the programming button until the RED &
BLUE LED’s are On.
4- Release the programming button.
5- Press & Hold the programming button again for 5 seconds until the BLUE & RED LED’s comes back On.
6- Release the programming button and Cycle the ignition to the ON position.
7- The RED, YELLOW & BLUE LED’s will be ON.
8- At that same moment the RED & BLUE LED’s will blink once to conrm that the MyCar ID has been
learned to the Evo-All.
9- Cycle the vehicle’s ignition to the OFF position to Exit EVO-ALL programming.
STEP 7. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
44
PARTS REQUIRED FOR INSTALLATION OF : FORTIN EVO-ONE
Telematics device HRN-MCAR-01 EVO-ONE HRN-LLRS-01
STEP 1. CONFIGURE THE REMOTE STARTER
The Fortin Flashlink is required to properly configure the EVO-ONE remote starter to accept the telematic
device. When flashing the EVO-ONE remote starter, please ensure to choose the following options: Toggle
your Flashlink connection mode to “Remote-Starter”. From the top menu click on “Configuration” and
then on “Unit Options”. In the “RF Kit Compatible” section, check the box next to “Fortin 2” and click
the save button on the top right of the screen.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics device
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-LLRS-01
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Evo-One remote
starter previously installed, you must set the protocol to “Fortin” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. LEARN THE MYCAR TELEMATICS DEVICE TO THE EVO-ONE
In order to communicate with the remote starter, the telematic system must be learned to the EVO-ONE.
1 - Cycle the ignition to the ON position.
2 - The YELLOW LED on top of the EVO-ONE should come ON.
3 - Press & Hold the EVO-ONE programming Valet button for 5 seconds.
4 - The RED LED on the side of the EVO-ONE will Flash rapidly.
5 - Release the push button.
6 - Press & Release the push button 5x times. Everytime the push button is pressed the parking lights
& the RED LED on the side of the EVO-ONE will blink.
7 - Then Press & Release the Brake pedal.
8 - At that same moment the RED LED on the side of the EVO-ONE will blink once to confirm that the
Telematic device ID has been learned to the EVO-ONE.
9 - Cycle the vehicle’s ignition to the OFF position to Exit the EVO-ONE programming.
STEP 7. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
46
PARTS REQUIRED FOR INSTALLATION OF : PRESTIGE (E) Models
Telematics device HRN-MCAR-01 (E) Model HRN-DRS-02
STEP 1. CONFIGURE THE REMOTE STARTER
The Voxx VEPROG is required to upgrade the latest Firmware and properly configure the Prestige (E)
remote starter to accept the telematics device. When updating the Prestige (E) remote starter, please
ensure to choose the correct Protocol option from Programming Bank 2, Feature #18, Option 3 or 4 “ADS
TEL”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
OR
PRO9776E
HRN-DRS-02
(1) Connect to supply power to telematics device
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Prestige (E) remote
starter previously installed, you must set the protocol to ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
48
PARTS REQUIRED FOR INSTALLATION OF : PRESTIGE (Z) Models
Telematics device HRN-MCAR-01 (Z) Model
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the Prestige (Z) remote starter to accept
the telematic device. When flashing the Prestige (Z) remote starter, please ensure to choose the correct
Protocol option from Programming Bank 2, Data Port Protocol, “ADS”.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics device
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Prestige (Z) remote
starter previously installed, you must set the protocol to ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
50
PARTS REQUIRED FOR INSTALLATION OF : PURSUIT (E) Models
Telematics device HRN-MCAR-01 (E) Model (Exc.PRO9233E) HRN-DRS-02
STEP 1. CONFIGURE THE REMOTE STARTER
The Voxx VEPROG is required to upgrade the latest Firmware and properly configure the Pursuit (E) remote
starter to accept the telematics device. When updating the Pursuit (E) remote starter, please ensure to
choose the correct Protocol option from Programming Bank 2, Feature #18, Option 3 or 4 “ADS TEL”.
STEP 2. CONNECT
STEP 3. NETWORK CONNECTIVITY
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
OR
3
HRN-DRS-02
(1) Connect to supply power to telematics device
INSTALLATION, WIRING & PROGRAMMING GUIDE
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Pursuit (E) remote
starter previously installed, you must set the protocol to ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Code Alarm remote
starter previously installed, you must set the protocol to ADS” and click “ACCEPT” then click “Done” at
the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
54
PARTS REQUIRED FOR INSTALLATION OF : OLDER CODE SYSTEMS
Telematics device HRN-MCAR-01 OLDER CODE SYSTEMS HRN-DRS-02
IMPORTANT NOTE: THESE OLDER MODELS ARE NOT SUPPORTED BY THIS PRODUCT.
INSTALLATION, WIRING & PROGRAMMING GUIDE
INSTALLATION, WIRING & PROGRAMMING GUIDE
56
PARTS REQUIRED FOR INSTALLATION OF : OMEGA RS-X70
Telematics device HRN-MCAR-01 RS-X70 BLADE-AL (64)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly configure the Omega RS-X70 remote starter to accept
the telematics device. When flashing the Omega RS-X70 remote starter, please ensure the remote starter
firmware and BLADE-AL (64) firmwares are updated to the latest firmware available. Also ensure to set
the “Data Port Protocol” to : “Green = iData”.
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics device
HRN-DRS-02 &
HRN-LLRS-01
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-DRS-01
HRN-LLRS-01
BLACK
DATA PORT
OR
OL-ADAPTER-B2G
GREEN
DATA PORT
METHOD #1
METHOD #2
METHOD #3
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Configuration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Omega RS-X70
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, configure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your configurations are all completed, click “Done” at the top right corner. All Configurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owner’s account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
58
PARTS REQUIRED FOR INSTALLATION OF : OMEGA AL-XX70-B
Telematics device HRN-MCAR-01 AL-XX70-B BLADE-AL (64)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the Omega AL-XX70-B remote starter to ac-
cept the telematics device. When ashing the Omega AL-XX70-B remote starter, please ensure the remote
starter firmware and BLADE-AL (64) firmwares are updated to the latest firmware available. Also ensure
to set the “Data Port Protocol” “Green = iData”. to :
STEP 2. CONNECT
(1) Connect only when remote starter is not supplying power to telematics devic
HRN-DRS-02 &
HRN-LLRS-01
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY (1)
GROUND (1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
HRN-DRS-01
HRN-LLRS-01
BLACK
DATA PORT
OR
OL-ADAPTER-B2G
GREEN
DATA PORT
METHOD #1
METHOD #2
METHOD #3
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the Omega AL-XX70-B
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
60
PARTS REQUIRED FOR INSTALLATION OF : DSE 503AIR 5R-85
Telematics device HRN-MCAR-01 DSE 503AIR 5R85
STEP 1. CONFIGURE THE REMOTE STARTER
The 503Air is already pre-congured to accept the telematics device. No extra programming required.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics devic
INSTALLATION, WIRING & PROGRAMMING GUIDE
62
PARTS REQUIRED FOR INSTALLATION OF : DSE iSTART2 - 3
Telematics device HRN-MCAR-01 DSE iStart2 - 3 CI3R-86 BLADE-AL (64)
STEP 1. CONFIGURE THE REMOTE STARTER
The ADS Weblink (ADS-USB) is required to properly congure the DSE iStart2 - iStart3 remote starter to ac-
cept the telematics device. When ashing the DSE iStart2 - iStart3 remote starter, please ensure the remote
starter rmware and BLADE-AL (64) rmwares are updated to the latest rmware available.
STEP 2. CONNECT
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT SIGNAL
FOR ALARM DETECTION
(+) 12V BATTERY
(1)
GROUND
(1)
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal surface
Orientation: Horizontal; small door
facing upward (as seen in this diagram)
(1) Connect only when remote starter is not supplying power to telematics devic
INSTALLATION, WIRING & PROGRAMMING GUIDE
STEP 3. NETWORK CONNECTIVITY
Once the telematics module is connected into the remote starter, two LED’s will display to which networks
you are connected to. (See LED Status Reference Chart on last page for details). NOTE: The vehicle may
need to be outside in an open area in order to connect to a cellular and/or GPS network.
STEP 4. ADD A DEVICE/VEHICLE TO AN ACCOUNT
a. Click the “+” sign at the bottom right of the Application screen. This will allow you to temporarily add
your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number” found at the back of the telematic device
(SN: XXXXXX-XXXXXXXXXX) and Click “Submit the code”.
c. You are now in “Test Mode”. Test Mode will allow you up to 4 hours for you to test the newly
installed device. At any time during this 4 hour period, you can exit testing mode and make unit “Ready
for Customer Delivery” by “Releasing the vehicle” or by “Transfering the vehicle” from your account.
NOTE: If you do NOT remove the vehicle from your account, it will automatically be removed from your
account and make the unit “Ready for Customer Delivery”.
STEP 5. PRE-CONFIGURE MYCAR APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. Click on the newly added vehicle from the vehicle list to enter the control screen (the screen that will al-
low you to control the vehicle’s remote start functions). This will automatically take you to the “Vehicle
Conguration” page for this vehicle. You will be prompt to “Set a Bypass Protocol” to use this device.
Click “Ok”.
b. Now you must set the protocol for the telematic device. When combined with the DSE iStart2 - iStart3
remote starter previously installed, you must set the protocol to “ADS” and click “ACCEPT” then click
“Done” at the top right corner.
c. Now please allow a moment (About 5 minutes) for the telematic device to update your protocol selec-
tion and reboot. After this wait period it will be available to accept commands from the App. In the
vehicle control screen, the Device Signal icon located above the Stop button will display the connectiv-
ity status of your telematic device. If the icon is Grayed out, Please wait, Device is still Oine. If icon is
Green, Device is Online and Ready to go.
d. Then from the top right click on of the Settings section edit the Vehicle name, congure the Auxiliaries
that might have been added if applicable and click ACCEPT when done. Then choose the vehicle to
display inside the control panel in the VEHICLE IMAGE section and click ACCEPT once done.
e. When your congurations are all completed, click “Done” at the top right corner. All Congurations will
take eect.
STEP 6. TEST YOUR DEVICE
When the system is Online you start testing the unit from the vehicle control panel. Test all the application
functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC.) When done with the testing, from the vehicle list you
can “Release” the vehicle. There are 2x dierent method to release it to the new owner. Choosing “release”
will simply remove it from your account and make it “Ready for Customer Delivery”. Choosing “transfer
will transfer the device to the new owners account.
Also make sure that the Owners Card is handed to the New Owner of the vehicle. Doing this will ensure
that the instructions on how to setup their App, Account and Vehicle is done correctly by using the device
serial number located on the sticker axed by the installer at the time of installation.
INSTALLATION, WIRING & PROGRAMMING GUIDE
64
LED Status Reference Chart
LED Status : Cellular Network : GPS NetworkGREEN LED RED LED
OFF No Cellular Network. No power to device. No GPS Network. No power to device.
Flashing Searching/Connecting Searching/Connecting
ON Solid Connection is established Connection is established
RESET PROCEDURE
1 - Disconnect the main harness from the MyCar device.
2 - Wait approximately 10 seconds and reconnect the main harness to the MyCar device.
3 - Reset procedure Completed.
INSTALLATION, WIRING & PROGRAMMING GUIDE
©2019 Automobility Distribution Inc. All rights reserved.
180 Marcus Blvd.
Hauppauge, NY
11788 - USA
QUICK INSTALLATION GUIDE
1. CONFIGURE THE REMOTE STARTER
a. To congure the remote starter to accept the CL6 telematics device, refer to the Detailed Installation and Programming guide for more
details. To access these guides, visit www.CL6.com . Complete the remote starter installation and conrm that it is working properly before
connecting the CL6 device.
2. CONNECT
a. Connect the CL6 telematics device by following the remote starter connection guide as shown on the back of this page. A detailed
wiring diagram can also be found in the Detailed Installation and Programming guide. (see Section #1 above for more details.)
3. NETWORK CONNECTIVITY
a. Once the telematics module is plugged into the remote starter, two LED’s will display what networks you are connected to.
b. LED STATUS
» Green LED Status : Cellular Network
» Red LED Status : GPS Network
i. OFF : No Communication - Check Power
ii. Flashing : Connecting to Network
iii. On Solid : Connection established
NOTE: The vehicle may need to be outside in an open area in order to connect to a cellular and/or GPS network.
4. INSTALL THE CL6 APPLICATION
a. Go to the App store (Apple) or Play store (Android)
b. Search for CL6”
c. Download and install the Free Application
5. CREATE AN ACCOUNT
NOTE: Already have an account? Go to the next step.
a. Launch the newly installed CL6 Application on your smartphone or tablet
b. Click “Create an Account”
c. Fill in all the required elds
d. Once completed, click “Create your Account”
e. Open your Mail and look for a new email sent from “MYCARCONTROLS”
f. To activate your account and create your secure password, click the embedded link in the email.
g. Create your secure password and activate your account.
h. Once done, Log into the Application using your email and your newly created password.
6. ADD A DEVICE/VEHICLE
a. In order to Pre-Congure your customers CL6 Application, click the “+” sign at the bottom right of the Application screen to
temporarily add your customers device/vehicle to your personal account.
b. Enter the 16 digit “Serial Number found at the back of the device. (SN: XXXXXX-XXXXXXXXXX)
c. Click “Submit the code”
7. PRECONFIGURE CL6 APPLICATION EXPERIENCE FOR YOUR CUSTOMER
a. From the “My Car Settings” menu congure the following
b. Edit the Vehicle name
c. Congure the Auxiliaries if needed. i.e.: Trunk release and associate the Auxiliary to activate when Aux button is pressed.
d. Edit the Vehicle image: Choose Year, Make, Model, Trim and Color of customers vehicle.
e. PROTOCOL SELECTION: (MANDATORY) The CL6 telematics device protocol must be set prior to use the device. To change the
Device Protocol, Tap and Hold the TAP TO CONFIGURE” button for approximately 8-10 seconds.
f. Select the desired protocol and Click Done when conguration is completed.
8. TEST YOUR DEVICE
NOTE: Make sure the vehicle is into an open space outside and that it has network connectivity.
a. Once in the vehicle control panel, the device will be in Test Mode” for a maximum time limit of 4 hours. During this period the
test device/vehicle can be removed and be set as “Ready for Customer Delivery at anytime. Although after the 4 hours time
window the device/vehicle in test will be automatically removed from the test account and will be considered “Ready for Customer
Delivery. This time window will allow enough time to send commands to the vehicle to test all remote starter functions.
RESET PROCEDURE
a. Disconnect the Device main harness.
b. Wait 10 seconds
c. Reconnect the Device main harness
d. Reset completed.
DOC DATE: 110317
Federal Communications Commission (FCC) Compliance Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation. CAUTION&KDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHPDQXIDFWXUHUUHVSRQVLEOHIRUFRPSOLDQFHFRXOGYRLGWKHXVHU¶VDXWKRULW\WRRSHUDWHWKHHTXLSPHQWNOTE7KLVHTXLSPHQWKDVEHHQWHVWHGDQGIRXQGWRFRPSO\ZLWKWKHOLPLWV
7KHVHOLPLWVDUHGHVLJQHGWRSURYLGHUHDVRQDEOHSURWHFWLRQDJDLQVWKDUPIXOLQWHUIHUHQFHLQDUHVLGHQWLDOLQVWDOODWLRQ7KLVHTXLSPHQWJHQHUDWHVXVHVDQGFDQUDGLDWHUDGLRIUHTXHQF\HQHUJ\DQGLIQRWLQVWDOOHGDQGXVHGLQDFFRUGDQFHZLWKWK
LVQRJXDUDQWHHWKDWLQWHUIHUHQFHZLOOQRWRFFXULQDSDUWLFXODULQVWDOODWLRQ,IWKLVHTXLSPHQWGRHVFDXVHKDUPIXOLQWHUIHUHQFHWRUDGLRRUWHOHYLVLRQUHFHSWLRQZKLFKFDQEHGHWHUPLQHGE\WXUQLQJWKHHTXLSPHQWRIIDQGRQWKHXVHULVHQFRXU
RUUHORFDWHWKHUHFHLYLQJDQWHQQD,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWLIIHUHQWIURPWKDWWRZKLFKWKHUHFHLYHULVFRQQHFWHG&RQVXOWWKHGH
This system must be installed by a professional.
3
(+) HORN (PULSE)
OR
(+) SIREN (CONSTANT)
ANALOG INPUT
SIGNAL FOR ALARM
(+) 12V BATTERY
GROUND
+12V Battery (RED)
Ground (BLACK)
Data (WHITE)
Data (BLUE)
Alarm(+) (YELLOW)
Installation:
Place module 3 inches
(minimum) from any metal
surface
Orientation: Horizontal; small
door facing upward (as seen in
this diagram)
REQUIRED
CM-6XXX
CM-7XXX
4X10 - 5X10
DBALL2
HRN-LLRS-01HRN-DRS-01
Telematics Port
REMOTE STARTER CONNECTION GUIDE
DOC DATE: 20161019-A
Federal Communications Commission (FCC) Compliance Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation. CAUTION&KDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHPDQXIDFWXUHUUHVSRQVLEOHIRUFRPSOLDQFHFRXOGYRLGWKHXVHU¶VDXWKRULW\WRRSHUDWHWKHHTXLSPHQW 7KLVHTXLSPHQWKDVEHHQWHVWHGDQGIRXQGWRFRPSO\ZLWKWKHOLPLWVNOTE
7KHVHOLPLWVDUHGHVLJQHGWRSURYLGHUHDVRQDEOHSURWHFWLRQDJDLQVWKDUPIXOLQWHUIHUHQFHLQDUHVLGHQWLDOLQVWDOODWLRQ7KLVHTXLSPHQWJHQHUDWHVXVHVDQGFDQUDGLDWHUDGLRIUHTXHQF\HQHUJ\DQGLIQRWLQVWDOOHGDQGXVHGLQDFFRUGDQFHZLWKWK
LVQRJXDUDQWHHWKDWLQWHUIHUHQFHZLOOQRWRFFXULQDSDUWLFXODULQVWDOODWLRQ,IWKLVHTXLSPHQWGRHVFDXVHKDUPIXOLQWHUIHUHQFHWRUDGLRRUWHOHYLVLRQUHFHSWLRQZKLFKFDQEHGHWHUPLQHGE\WXUQLQJWKHHTXLSPHQWRIIDQGRQWKHXVHULVHQFRXU
RUUHORFDWHWKHUHFHLYLQJDQWHQQD,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWLIIHUHQWIURPWKDWWRZKLFKWKHUHFHLYHULVFRQQHFWHG&RQVXOWWKHGH
This system must be installed by a professional.
Connects
here
OWNER’S CARD
Thank you for purchasing CL6
For Terms and Conditions, see the Terms and Conditons under the main menu in the app.
Prod
Step 1: App & Account Setup
1. Start by downloading the CL6 smartphone app.
2. Once completed, Launch the CL6 app on your device.
3. Click the “Create an Account” and ll in all of the required elds then click the “Creat
4. Open your email and look for a new email from “MYCARCONTROLS”
5. To activate your account and create your password, click on the link in the email.
6. Create your secure password and activate your account
7. Once done, log into the app using your email address and new secure password.
Step 2: Add A Device/Vehicle
1. Click on the (+) sign in the bottom right corner of the “My Cars” screen to add your d
account.
2. Enter the 16 digit “Serial Number” found in the upper right hand corner of this docu
(SN:XXXXXX-XXXXXXXXXX)
3. Click the “Submit the Code”.
ATTENTION
If installing the Carlink ASCL6 with any one of the VOXX Brands (Prestige, Pursuit, Or
Code Alarm) the Alarm/Remote start module must be updated to the latest rm-
ware version. This will require the VOXX USB updating cable, Part# VEPROG.
Prestige/Pursuit: Please visit www.veprog.com to update to the latest rmware
version.
Code Alarm: Please visit www.voxxuniversity.com to download the CA Utility APP.
The APP can be found in the VOXXTECH section of the website.
COMPATIABLE SYSTEMS
Prestige/Pursuit: All E models w/ telematics port (Except PRO9233E)
Code Alarm: CASECRS, CARS & CA4555
Flash Logic: All FLRS remote start modules including FLCAN (RS Firmware
w/ adapter)
Omega: All modules with telematics port
For customer or technical support please call Voxx Support:
1-800-225-6074
9 AM 6 PM (EST - Eastern)
Monday Friday
VOXX Electronics Corporation, 180 Marcus Blvd., Hauppauge, New York 11788


Product specificaties

Merk: Audiovox
Categorie: Afstandsbediening
Model: Code Alarm ASCL6 CarLink

Heb je hulp nodig?

Als je hulp nodig hebt met Audiovox Code Alarm ASCL6 CarLink stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsbediening Audiovox

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening