Audio-Technica ES925ML/FM5 Handleiding

Audio-Technica Microfoon ES925ML/FM5

Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica ES925ML/FM5 (3 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
1
ES925ML6/FM5
ES925ML12/FM5
ES925ML15/FM5
ES925ML18/FM5
ES925ML21/FM5
ES925ML24/FM5
User Manual
MICROLINE CONDENSER
MODULAR GOOSENECK MICROPHONE
WITH 5-PIN FLUSH-MOUNT POWER MODULE
■Introduction
Thank you for purchasing this product. Before using the product, read through
the user manual to ensure that you will use the product correctly. Please keep
this manual for future reference.
■Features
• Modular microphone system comprised of an ES Series capsule, gooseneck
assembly, and power module.
• RGB LEDs built into both the flush-mount power module and gooseneck
assembly indicate the on/off status of the microphone.
• Includes external control function for device control from the capacitive touch
switch.
• The capacitive touch switch can be set to any of three operating modes:
“touch-on/touch-off”, “touch-to-talk” and “touch-to-mute”.
■Safety precautions
Although this product was designed to be used safely, failing to use it correctly
may result in an accident. To ensure safety, observe all warnings and cautions
while using the product.
■Cautions for the product
• Do not subject the product to strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a
hot, humid or dusty place.
■Notes on use
• Check the strength of the mounting area. Insufficient strength or poor
mounting will cause objects to fall or become damaged.
• The circuitry in the microphone takes about 30 seconds to stabilize after power
is supplied. You may hear some audio disturbance during startup.
• Install the microphone on a flat, unobstructed mounting surface.
• Depending on the surface finish of a table, the isolators may leave marks on
the table.
• Do not excessively bend the gooseneck assembly, rotate the ends of the
capsule, or pull on them. Doing so may cause disconnection or malfunction.
• The product is a modular system comprised of a microphone element,
gooseneck assembly and power module. Make sure the parts are firmly
attached before use.
• Do not remove the rubber O-ring on the power module connecting part at the
lower section of the gooseneck assembly.
• When attaching parts, remove the black cap on the capsule connecting part
of the gooseneck assembly. Do not remove the silicone part at the end of
the capsule connecting part.
Silicone part
Do not remove
2
■Assembly
• Insert the gooseneck assembly (c) while rotating it into the flush-mount power
module (d).
• Tighten until it does not rotate, and use the hex wrench (i) to tighten the set
screw (h) and set the gooseneck assembly in place.
• Connect the capsule (b) to the gooseneck assembly, and attach the windscreen (a).
* If the parts are not sufficiently tightened together, problems may occur such as
the LED colors of the gooseneck assembly and power module not matching or
sound is not output.
• Refer to the LED table to the right and set the LED color before attaching to
the mounting surface.
• If you are installing the flush-mount power module on a table without the isolators,
you must make a hole with a diameter of 20.5 mm in the mounting surface.
• If you are installing with the isolators, the hole must have a diameter of 23.5 mm.
Inserting the isolators between the mounting surface and power module allows
you to separate the flush-mount power module from the mounting surface.
• Attach the upper part isolator (e) to the mounting surface, and attach the flush-
mount power module (d). Attach the lower isolator (f) to the reverse side of the
mounting surface, and then tighten the nut (g).
c
d
e
f
g
hi
a
b
■Switch setting and functions
1
5
4
MIC
2
Contact
Closure
GND
1. Action 5. LED
status
4. LED color
3. Audio
status
2. Contact
closure
status
■LED color
1 2 3
OFF RED GREEN
YELLOW
4 5 6 7
BLUE
MAGENTA
CYAN WHITE
■Wiring
PIN1
(Ground)
PIN5
(LED control)
PIN4
(Contact closure)
PIN3
(Cold)
PIN2
(Hot)
3
142419812-02-01 ver.1 2019.06.01
■Specifications
ES925MLx/FM5
Element Fixed-charge back plate, permanently polarized condenser
Polar pattern Line + Gradient
Frequency response 30 - 20,000 Hz
Open circuit sensitivity -35dB (17.7mV) (0dB=1V/Pa, 1kHz)
Impedance 130 ohms
Maximum input sound
level 137 dB SPL (1kHz at 1% THD)
Dynamic range 114 dB (1kHz at Max SPL)
Signal-to-noise ratio 71 dB (1kHz at 1Pa, A-weighted)
Phantom power
requirements 22 - 52 V DC, 7.6 mA
Contact closure
Closure input voltage
Maximum permissible
power
On-resistance
-0.5 - 5.5 V
200 mW
100 ohms
LED control
Active low voltage
Maximum permissible
input power
Maximum permissible
power
Active high (+5 V DC) TTL compatible
1.2 V or lower
-0.5 - 5.5 V
200 mW
Weight
ES925ML6/FM5: 114.2 g (4.0 oz)
ES925ML12/FM5: 138.2 g (4.9 oz)
ES925ML15/FM5: 143.2 g (5.1 oz)
ES925ML18/FM5: 148.2 g (5.2 oz)
ES925ML21/FM5: 153.2 g (5.4 oz)
ES925ML24/FM5: 158.2 g (5.6 oz)
Dimensions
ES925ML6/FM5: 326.5 mm (12.9“) x 38 mm (1.5“) x 48 mm (1.9“)
ES925ML12/FM5: 434 mm (17.1“) x 38 mm (1.5“) x 48 mm (1.9“)
ES925ML15/FM5: 510.2 mm (20.1“) x 38 mm (1.5“) x 48 mm (1.9“)
ES925ML18/FM5: 586.4 mm (23.1“) x 38 mm (1.5“) x 48 mm (1.9“)
ES925ML21/FM5: 662.6 mm (26.1“) x 38 mm (1.5“) x 48 mm (1.9“)
ES925ML24/FM5: 738.8 mm (29.1“) x 38 mm (1.5“) x 48 mm (1.9“)
(H×W×D)
Output connector 5-Pin XLRM-type
Optional interchangeable
elements ESE-Ca (120°), ESE-Ha (100°), ESE-Oa (360°)
Included accessories Isolator 1 pair, Nut, Windscreen AT8138a,
Set screw (M2×2 mm (0.08“)) 2 pcs., Hex wrench (M2)
■Polar pattern
240˚
180˚
210˚
270˚
300˚
330˚
0˚
150˚
120˚
90˚
30˚
60˚
SCALE IS 5 DECIBELS PER DIVISION
200 Hz
1 kHz
5 kHz
8 kHz
LEGEND
■Frequency response
5020 20k10k5k2k1k500200100
Response in dB
Frequency in Hertz
LEGEND
0°, 50cm
■Dimensions
ES8755RC (FM5)
38.0
20.0
48.0
x = 6/12/15/18/21/24
10dB
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2019 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
Made in Japan
ES925ML6/FM5 ES925ML12/FM5 ES925ML15/FM5 ES925ML18/FM5 ES925ML21/FM5 ES925ML24/FM5
(unit: mm)
326.5
434.0
510.2
586.4
662.6
738.8
φ8.0

Product specificaties

Merk: Audio-Technica
Categorie: Microfoon
Model: ES925ML/FM5

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica ES925ML/FM5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Microfoon Audio-Technica

Audio-Technica

Audio-Technica ATR7700 Handleiding

6 December 2024
Audio-Technica

Audio-Technica ATR7500 Handleiding

6 December 2024
Audio-Technica

Audio-Technica ATR3500 Handleiding

6 December 2024
Audio-Technica

Audio-Technica ATR3700 Handleiding

6 December 2024
Audio-Technica

Audio-Technica AT8703 Handleiding

6 December 2024
Audio-Technica

Audio-Technica AT2040USB Handleiding

6 December 2024
Audio-Technica

Audio-Technica PRO35 Handleiding

6 December 2024
Audio-Technica

Audio-Technica ATM75cW Handleiding

6 December 2024
Audio-Technica

Audio-Technica ATS99 Handleiding

6 December 2024
Audio-Technica

Audio-Technica PRO41 Handleiding

6 December 2024

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon

Sennheiser

Sennheiser A 9000 Handleiding

20 December 2024
Sony

Sony DWT-P30 Handleiding

18 December 2024
BOYA

BOYA BY-M1000 Pro Handleiding

18 December 2024
PSC

PSC PowerStar RF Handleiding

17 December 2024
PSC

PSC RF Multi SMA Handleiding

17 December 2024
Power Dynamics

Power Dynamics PD210 Handleiding

15 December 2024
Power Dynamics

Power Dynamics PD220 Handleiding

15 December 2024
Behringer

Behringer Go Cam Handleiding

14 December 2024
Behringer

Behringer HM50 Handleiding

14 December 2024
Behringer

Behringer BC444 Handleiding

14 December 2024