Audio-Technica BP4025 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica BP4025 (2 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
X/Y STEREO FIELD RECORDING MICROPHONE
- Designed for broadcast and professional recording, and eld
use
- Unique coincident capsule conguration produces accurate
stereo image in smaller housing
- Large-diaphragm capsules for pristine sound quality and
exceptionally low noise
- Compact, lightweight design is ideal for camera-mount use
- Excellent channel separation
- Integral 80 Hz HPF switch and 10 dB pad
The BP4025 is intended for use in professional applications
where remote power is available. It requires 11V to 52V DC
phantom power, which may be provided by an audio mixer, or by
a separate, in-line source such as the Audio-Technica AT8801
single-channel or AT8506 four-channel phantom power supplies.
Output for each stereo channel is low impedance (Lo-Z)
balanced. The balanced signals appear across Pins 2 and 3
for the left channel, Pins 4 and 5 for the right channel. Pin 1 is
ground (shield) for both channels. Output is “Pins 2 and 4 hot”
- positive acoustic pressure produces positive voltage at Pins 2
and 4.
Locating the BP4025 nearer the sound source enhances the
width of the stereo image, while decreasing room ambience.
Conversely, as the mic position moves away from the sound
source, a narrower left/right stereo image results and more of the
“room sound” is noted.
An integral 80 Hz high-pass lter provides easy switching from a
at frequency response to a low-end roll-off. The roll-off position
reduces the pickup of low-frequency ambient noise (such as
traffic, air-handling systems, etc.), room reverberation and
mechanically coupled vibrations.
The BP4025 is also equipped with a switchable 10 dB pad that
lowers the microphone's sensitivity, thus providing higher SPL
capability for exible use for a wide range of speakers/performers
and system congurations.
The microphone is RoHS compliantfree from all substances
specied in the EU directive on hazardous substances.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 43°C for extended periods. Extremely high
humidity should also be avoided.
FORM No. ATGC-L0140-08-E
10 dB
20k10k5k2k1k50020010050
Frequency Response
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
Machida Tokyo Japan
SPECIFICATIONS
ELEMENT Fixed-charge back plate
permanently polarized condenser
CHANNEL BALANCE <2.5 dB
POLAR PATTERN X/Y Stereo
FREQUENCY RESPONSE 20-17,000 Hz
LOW FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave
OPEN CIRCUIT SENSITIVITY -32 dB (25.1 mV) re 1V at 1 Pa
IMPEDANCE 170 ohms
MAXIMUM INPUT SOUND LEVEL 145 dB SPL, 1 kHz at 1% T.H.D.;
155 dB SPL, with 10 dB pad
DYNAMIC RANGE (typical) 131 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO 80 dB, 1 kHz at 1 Pa
PHANTOM POWER REQUIRMENTS 11 - 52V DC, 7 mA (both channels)
SWITCHES Flat, roll-off; 10 dB pad (norminal)
WEIGHT (less cable and accessories) 269 g
DIMENSIONS 186.0 mm long,
47.6 mm head diameter,
21.0 mm maximum body diameter
OUTPUT CONNECTOR Integral 5-pin XLRM-type
CABLES 5.0m long, 8 conductor, shielded,
viny l-jac keted s tereo c able wi th
5- pin XL RF-ty pe c on nec tor at
mi cropho ne end a nd two 3- pi n
XLRM-type connectors at output
end
ACCESSORIES FURNISHED AT8405a sta nd clamp for "-27
threaded stands; windscreen; soft
protective pouch
Roll-off
200 Hz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
200 Hz
Polar Pattern
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
LEFT RIGHT
1 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
1 kHz
Polar Pattern
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
LEFT RIGHT
8 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
8 kHz
Polar Pattern
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
LEFT RIGHT
10 dB
20k10k5k2k1k50020010050
频率特性
频率 (
赫兹)
电平 平直
响应电平 (dB)
FORM No. ATGC-L0140-08-C
X/Y立体声现场收音话筒
- 广访
- 独 特 的 配 对 式 收 音 头 , 设 置 于 细 小 的 头 罩 内 , 提
- 大型收音膜片,可提供清澈的音色和特低的噪
- 使用。
-
- 80Hz10dB
BP4025 11V 52V应用于专业收音工作, 要提供
幻象供电工作,,可使用调音台上的幻象电源,也
使AT8801 AT8506单通道或 四通道
话筒的每通道输出端为低阻抗平衡输出,话筒音频
信号最终以卡农公头的2号 及 3号针脚作左通道输
出 , 4号 及5号 针 脚 作 右 通 道 输 出 , 而1号 针 脚 则 为
左 右 通 道 地 线 (屏 蔽 )连 接 输 出 相 位 将 以 正 相 位 电
平设于24
请 把 话 筒 放 置 于 接 近 音 源 的 位 置 , 以 减 少B P 4 0 2 5
回音混响和提高立体声收音效果。远离音源时会收
内置高通滤波电路,可轻易由平直的频率响应,开
启为于8 0 H z 以下衰减的收音效果,应用高通滤波
器可减低收音环境中低频噪声(
),房间中的回声及机械性的震动
BP4025 10dB话同并有 衰减开关,在高声压环境收
音时,减低话筒的灵敏度,避免破声的失真现象出
话 筒 符 合 R o H S 规 格 , 在 构 造 上 不 含 有 欧 盟 禁 用 的
把话筒暴露于高温中可能导致输出电平逐渐及永久
性减弱,应避免将话筒留在日晒的地方或长时间置
43 °C湿Machida Tokyo Japan
技术指标
收音头 固定充电背板,
静电型电容式
通道平衡 <2.5 dB
指向特性 X/Y 立体声
频率响应 20-17,000 Hz
高通滤波 80 Hz, 12 dB/octave
开通灵敏度 -32 dB (25.1 mV) 1V 1 Pa
输出阻抗 170 欧姆
最大承受声压 145 dB 声压, 1 kHz 1% T.H.D. ;
155 dB 声压 10dB 衰减
动态范围 (典型) 131 dB, 1 kHz
于最高声压
讯噪比 80 dB, 1 kHz 1 Pa
幻像供电 直流 11 - 52V, 耗电 7mA 典型每通道
开关 平直 / 高通滤波
; 10dB 衰减
重量 269 g
外形尺寸 186.0 mm ,
47.6 mm 头罩直径
21.0 mm 机身最大直径
输出连接器 内置 XLRM-5针卡农公头
连线 平衡接线: 5.0 m 长,
8芯线屏蔽式
聚乙烯护套立体声电缆带 5针卡农母
头连接话筒,及两路3针卡农公头于
输出端。
附属品 AT8405a "-27轴式;防
风罩;电池;保护软袋
高通滤波
200 Hz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
200 Hz
指向特性
声压曲线1刻度
5 dB
频率
左收音头 右收音头
8 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
8 kHz
指向特性
声压曲线 1刻度
5 dB
频率
左收音头 右收音头
1 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
1 kHz
指向特性
声压曲线1刻度
5 dB
频率
左收音头 右收音头


Product specificaties

Merk: Audio-Technica
Categorie: Microfoon
Model: BP4025

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica BP4025 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Microfoon Audio-Technica

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon

Sony

Sony ECM-322BMP Handleiding

22 November 2024
Sony

Sony ECM-S1 Handleiding

22 November 2024
Sony

Sony ECM-W3S Handleiding

22 November 2024
Sony

Sony ECM-W3 Handleiding

22 November 2024
Sony

Sony ECM-M1 Handleiding

22 November 2024
Sony

Sony XLR-H1 Handleiding

22 November 2024
Sony

Sony ECM-678 Handleiding

22 November 2024
Sony

Sony ECM-XYST1M Handleiding

22 November 2024