Audio-Technica AT8539 Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor Audio-Technica AT8539 (1 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Features
ā€¢ HRS-type input connector allows any A-T Wireless EssentialsĀ®
microphone to function as a wired model
ā€¢
Switchable low-cut ī˜lter minimizes pickup of unwanted low
frequencies
ā€¢ XLRM-type output connector
ā€¢ Designed to plug directly into an XLR-type chassis connector
ā€¢ Rugged steel case construction
Description
The AT8539 power module allows any Audio-Technica Wireless
EssentialsĀ® microphone to operate as a wired microphone. The power
moduleā€™s HRS-type 4-pin input connector mates with any Audio-Technica
Wireless EssentialsĀ® (wireless microphone with model number ending in
a cW); its output is a standard 3-pin XLRM-type connector.
It offers a low-cut īš†lter to help minimize the pickup of unwanted low
frequencies. To engage the low-cut īš†lter, use the end tip of a paperclip or
other small pointed instrument to slide the switch toward the ā€œbentā€ line.
The power module is constructed of rugged steel for maximum durability
and optimum shielding from hum. A snap-on belt clip is included.
Architectā€™s and Engineerā€™s Speciī˜Šcations
The in-line power module shall allow any Audio-Technica wireless
microphone terminated with a 4-pin HRS-type connectors to connect
to a wired microphone circuit. The input connection shall be through an
HRS-type 4-pin connector. Output shall be a standard 3-pin XLRM-type
connector. The power module shall convert the audio signal to a standard
balanced line microphone level output as well as provide operating DC
bias voltage for the attached microphone. An integral low-cut īš†lter shall,
when engaged, roll off the low-end audio at 80 Hz with a slope of 18 dB
per octave. The īš†lter shall be engaged via a recessed switch. The power
module shall be constructed of metal for optimum shielding from hum.
Output impedance shall be 250 ohms.
The Audio-Technica AT8539 is speciīš†ed.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
Ā©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0239-00
Speciī˜Šcations
HRS-type 4-pin / XLRM-type
Microphone dependent
250 ohms
80 Hz, 18 dB/octave
11-52V DC, 2 mA typical
Flat / Roll-off
97.6 mm (3.84") long ,
18.9 mm (0.74") diameter
Belt clip
Input/Output connectors
Frequency response
Impedance
Low-cut ī˜‰lter
Phantom power
Switch
Dimensions
Accessory included
In the interest of standards development, A.T.U.S. offers
full details on its test methods to other industry profes-
sionals on request.
Speciīš“cations are subject to change without notice.
AT8539
Power Microphones
electronics


Product specificaties

Merk: Audio-Technica
Categorie: Microfoon
Model: AT8539

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica AT8539 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Microfoon Audio-Technica

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon