Audio-Technica AT4053b Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica AT4053b (2 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
HYPERCARDIOID CONDENSER MICROPHONE
- Specially engineered to meet the most critical acoustic requirements of
professional recording, broadcast and sound reinforcement
- Direct-coupled, balanced output results in a clean signal even under
high-output conditions
- Transformerless circuitry virtually eliminates low-frequency distortion and
provides superior correlation of high-speed transients
- Switchable 80 Hz hi-pass lter and 10 dB pad
- Rugged turned-brass microphone housing for enduring dependability
- State-of-the-art design and manufacturing techniques ensure
compliance with A-T’s stringent consistency and reliability standards.
The AT4053b is intended for use in professional applications where
remote power is available. It requires 48V DC phantom power, which may
be provided by a mixer or console, or by a separate, in-line source such
as the Audio-Technica AT8801 single-channel or CP8506 four-channel
phantom power supplies.
Output from the microphone's XLRM-type connector is low impedance
(Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is
ground (shield). Output phase is “Pin 2 hot” positive acoustic pressure
produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be wired
consistently: Pin 1-to-Pin 1, etc.
An integral 80 Hz hi-pass filter provides easy switching from a flat
frequency response to a low-end roll-off. The high-pass position reduces
the microphone's sensitivity to popping in close vocal use. It also reduces
the pickup of low-frequency ambient noise (such as trafc, air-handling
systems, etc.), room reverberation and mechanically coupled vibrations.
The AT4053b consists of two modular subassemblies: an AT4900b-48
body and an AT4053b-EL head capsule (both available separately).
Additional interchangeable capsules are available in omnidirectional
(AT4049b-EL) and cardioid (AT4051b-EL).
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 43°C for extended periods. Extremely high humidity
should also be avoided.
FORM No. ATGC-L0161-09-E
Machida Tokyo Japan
SPECIFICATIONS
ELEMENT Externally polarized (DC bias)
capacitor
POLAR PATTERN Hypercardioid
FREQUENCY RESPONSE 20-20,000 Hz
OPEN CIRCUIT SENSITIVITY -34 dB (19.9 mV) re 1V at 1 Pa
IMPEDANCE 50 ohms
MAXIMUM INPUT SOUND LEVEL 145 dB SPL, 1 kHz at 1% T.H.D.
155 dB SPL, with 10 dB pad (nominal)
NOISE 16 dB SPL
DYNAMIC RANGE (typical) 129 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO 78 dB, 1 kHz at 1Pa
LOW FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave
PHANTOM POWER REQUIREMENTS 48V DC, 4.8 mA typical
SWITCH Flat, roll-off; 10 dB pad (nominal)
WEIGHT (less accessories) 127 g
DIMENSIONS 155.0 mm - long,
21.0 mm - body diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED AT8405a snap-in clamp for ⅝”-27
threaded stand; windscreen;
protective carrying case
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
Polar Pattern
Frequency Response
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
Frequency in Hertz
LEGEND 12” or more on axis
Response in dB
Optional Accessories:
AT4049b-EL omnidirectional microphone
capsule.
AT4051b-EL cardioid microphone capsule.
AT8106 metal-frame pop lter.
AT8114 foam windscreen for AT8106 pop
lter.
AT8506 four-channel 48V phantom power
supply (AC powered).
AT8801/EU single-channel 48V phantom
power supply (AC powered).
Roll-off
10 dB
20k10k5k2k1k50020010050
8 kHz
200 Hz
1 kHz
5 kHz
330°
300°
270°
240°
210°
180°
150°
120°
90°
60°
30°
指向特性
频率特性
声压曲线 1刻度5 dB
频率
频率 ( )
电平 平直
响应电平 (dB)
FORM No. ATGC-L0161-09-C
Machida Tokyo Japan
- 特别按专业录音、广播和增强音色的重要要求而设计
-
- 无变压器输出电路,可减少低频失真和提高瞬间响应的清晰
度。
- 80Hz高通滤波及10dB衰减开关
- 性。
-
定的严密标准和可靠性。
AT4053b 48V需要使用 幻象供电工作,可使用专业调音台上
使用 三 AT8801 AT8506
四通道幻象电源供电器作独立供电
低阻抗的平衡音频输出,话筒音频信号最终以卡农公头的
23号针脚输出,而1号针脚则为地线()连接。输出
相位将以正相位电平设于2号针脚上。
为濶免出现相位相互抵消而失真的情况,所有话筒连接
时,接线必需以1-12-23-3型式把针脚连接。
内置高通滤波电路,可轻易由平直的频率响应,开启为于
80Hz以下衰减的收音效果,应用高通滤波器可减低收音环
(如外间汔车引擎声,空调系统的风声等)
房间中的回声及机械性的震动声。
AT 405 3b 超心形指向性话筒以 AT 4 053 b-EL 收音头及
AT4900b-48 AT4049b-
EL (全方向指向性) AT4051b-EL (
心形指向性)
应避免将话筒留在日晒的地方或长时间置于温度超过43°C
地方,而极高湿度也应避免。
技术指标
收音头 直流偏压型电容式
指向特性 超心形指向性
频率响应 20-20,000 Hz
开通灵敏度 -34 dB (19.9 mV) 1V 1 Pa
输出阻抗 50 欧姆
最大承受声压 145 dB, 1 kHz 1% T.H.D.
155 dB, 10dB
噪声 16 dB 声压
动态范围 (典型) 129 dB, 1 kHz 于最高声压
讯噪比 78 dB, 1 kHz 1Pa
高通滤波 80 Hz, 12 dB/octave
幻象供电 直流 48V,耗电 4.8 mA
典型
开关 平直 / 高通滤波;10dB
重量 127
外形尺寸 155.0 mm - 长度, 21.0 mm - 直径
输出连接器 内置 XLRM-3针卡农公头
附属品 AT8405a ⅝”-27接头架,
保護袋,海棉防风罩。
选择配件 :
AT4049b-EL 全指向性收音头。
AT4051b-EL 心形向性收音头。
AT8106 金属防喷气保护网
AT8114 球形海棉防风罩 (AT8106)
AT8506 四通通48V幻象供电器 (
交流供
)
AT8801/EU 单通道48V幻象供电器 (
流供电 )
高通滤波


Product specificaties

Merk: Audio-Technica
Categorie: Microfoon
Model: AT4053b

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica AT4053b stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Microfoon Audio-Technica

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon