Atto FastFrame NS14 Handleiding

Atto Netwerkkaart/adapter FastFrame NS14

Lees hieronder de 📖 handleiding in het Nederlandse voor Atto FastFrame NS14 (2 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

ATTO Technology, Inc.

155 CrossPoint Parkway

Amherst, New York 14068 USA

www.attotech.com

Tel (716) 691-1999

Fax (716) 691-9353

Sales support: sls@attotech.com

Technical support: Monday -- Friday, 8am-6pm EST

techsupp@attotech.com (716) 691-1999 x242

No part of this document may be reproduced in any form or by any means without the express written permission of ATTO

Technology, Inc.

7/2011 PRMA-0430-000MD

FastFrame™ 10GbE Network Interface Card

Getting Started Guide

Thank you for purchasing the ATTO FastFrame 10GbE Network Interface Card (NIC). This guide gives you the

basics for installing and configuring your adapter. For more information, please visit our website at

www.attotech.com

1 Overview

This guide covers hardware and software installation,

setup procedures, and troubleshooting tips for ATTO

FastFrame

10Gb

Ethernet adapters.

Note

This guide refers to drivers and features available on IA-32-

based computer platforms and platforms based on Intel®

Extended Memory 64 Technology. These drivers are not

compatible with Itanium®-based computers.

2 System Requirements:

Before installing the ATTO FastFrame 10GbE Ethernet

Adapter, check your system for the following minimum

configuration requirements.

Supported Operating Systems

• Microsoft Windows 7

• Microsoft Windows Vista

• Microsoft Windows XP

• Microsoft Windows Server 2003

• Microsoft Windows Server 2008

• Microsoft Windows Server 2008 R2

• Mac OS X 10.6 & later

• Red Hat Enterprise Linux 5 & 6

• SUSE Linux Enterprise Server 10 & 11

• openSUSE 11.2 and 11.3

• Fedora 13 & 14

The installer for the adapter drivers will only list the

drivers that are compatible with the currently running

operating system.

3 Installing and Uninstalling the

Drivers

Before you begin

Note

To successfully install or uninstall the drivers or software, you

must have administrative privileges on the computer

completing installation.

Install the Drivers in Microsoft Windows

Note

This will update the drivers for all supported ATTO® network

adapters in your system.

Before installing or updating the drivers, insert your

adapter(s) in the computer and plug in the network

cable. When Windows discovers the new adapter, it

attempts to find an acceptable Windows driver already

installed with the operating system.

If found, the driver is installed without any user

intervention. If Windows cannot find the driver, the

Found New Hardware Wizard window is displayed.

Regardless of whether or not Windows finds the driver,

it is recommended that you follow the procedure below

to install the driver.

3.1 Download drivers from the support website and transfer

them to the system.

3.2 If the Found New Hardware Wizard screen is displayed,

click Cancel.

3.3 The autorun automatically runs after you have extracted

the files.

3.4 Run the winxx_drv_fastframe_nicxx based on the

operating system (x86 or x64) in use. If you are unsure

which version you are using, please contact your system

administrator.

3.5 The autorun automatically executes after you have

extracted the files.

3.6 Follow the instructions in the install wizard.

Install the Drivers in Mac OS X

3.1 Go to the http://www.attotech.com/downloads.html

3.2 Log in.

3.3 Under ‘Select Product’ choose Ethernet Adapters.

3.4 Select 10GbE Network Interface Cards.

3.5 Download the latest Mac driver.

3.6 Open the driver from the location in which it was saved.

3.7 Follow the on-screen instructions.

Install the Drivers in Linux

The driver file (

ixgbe

) should be present in recent Linux

operating system versions. Additional installation steps are not

required.

Uninstalling the Windows Driver

These instructions uninstall the drivers for all ATTO

adapters in a system.

3.1 From the Control Panel, double-click Add/Remove

Programs.

3.2 Select Intel(R) Network Connections Drivers.

3.3 Click Add/Remove.

When the confirmation dialog displays, click OK.

4 Hardware Installation

Note

If you are replacing an existing adapter with a new adapter, you

must re-install the driver.

Insert a PCI Express Adapter in the Server

4.1 Turn off the server and unplug the power cord, then remove

the server's cover.

CAUTIONCAUTION

Turn off and unplug the server before removing the server's

cover. Failure to do so could endanger you and may damage the

adapter or server.

4.2 Remove the cover bracket from a PCI Express slot (v1.0a or

later).

PCI-Express slots and adapters vary in the number of

connectors present, depending on the data lanes being

supported.

4.3 Insert the adapter in an available, compatible PCI Express

slot. Push the adapter into the slot until the adapter is firmly

seated. The adapter can be installed in p2-x8 or x16

mechanical PCIe slot.

CAUTIONCAUTION

Some PCI-Express adapters may have a short connector,

making them more fragile than PCI adapters. Excessive force

could break the connector. Use caution when pressing the board

in the slot.

4.4 Repeat steps 2 through 3 for each adapter you want to

install.

4.5 Replace the server cover and plug in the power cord.

4.6 Turn the power on.

Connect a 10GbE Fibre Network Cable

CAUTIONCAUTION

This product uses a Class 1M laser module. Viewing the

laser output with certain optical instruments designed for

use at a distance (for example, telescopes and binoculars)

may pose an eye hazard.

Remove and save the fiber optic connector cover. Insert a

fiber optic cable into the ports on the network adapter

bracket as shown.

Most connectors and ports are keyed for proper

orientation. If the cable you are using is not keyed, check

to be sure the connector is oriented properly (transmit port

connected to receive port on the link partner, and vice

versa).

For ATTO FastFrame 10Gb Ethernet Adapters:

Laser wavelength: 850 nanometer

Cable type to use: Multi-mode fiber with 62.5µm or 50µm

core diameter

Connector type: LC.

Maximum cable length: 300 meters (with laser optimized).

The adapter must be connected to a compatible link

partner, such as an IEEE 802.3ae-compliant 10-gigabit

switch, which is operating at the same laser wavelength

as the adapter.

SFP+ Devices with Pluggable Optics

Your ATTO FastFrame 10Gb Ethernet Adapter comes

with ATTO supplied, high performance optics and only

these optics are supported.

5 Configure Network Settings

To configure your adapter settings, consult your System

Administrator or System Documentation.

6 Configure your Adapter

Default settings are appropriate for most systems but you may

change settings using the Device Manager in windows or

EthTool in Linux.

Product specificaties

Merk:	Atto
Categorie:	Netwerkkaart/adapter
Model:	FastFrame NS14
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Certificering:	FCC
Interface:	Fiber
Voldoet aan industriestandaarden:	EN60950-1, EN60825-1, EN60825-2
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000,10000 Mbit/s
Netwerkstandaard:	IEEE 802.1Q, IEEE 802.3ad, IEEE 802.3ae
Ondersteunt Windows:	Ja
Temperatuur bij opslag:	-40 - 70 °C
Intern:	Ja
Compatibele besturingssystemen:	Windows Server 2003, 2008, Windows XP, Vista, 7, Red Hat (RHEL) / SUSE (SLES) Linux, Mac OS X
Ondersteunt Mac-besturingssysteem:	Ja
Ondersteunt Linux:	Ja
Veiligheid:	RoHS
Hostinterface:	PCI Express
Maximale overdrachtssnelheid van gegevens:	10000 Mbit/s
Datastroombeheer:	Ja
Link/Act LED:	Ja
Jumbo Frames ondersteuning:	Ja
Component voor:	PC
Wifi:	Nee
Stroomverbruik (typisch):	15.7 W
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Vezel-optische connector:	LC
Fibre channel-poorten:	4