Atlona AT-VCC-RS232-KIT Handleiding

Atlona Niet gecategoriseerd AT-VCC-RS232-KIT

Lees hieronder de 📖 handleiding in het Nederlandse voor Atlona AT-VCC-RS232-KIT (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Installation Guide

AT-VCC-RS232-KIT

IP to RS-232 Command Converter for Velocity Control

System

AT-VCC-RS232-KIT

The Atlona AT-VCC-RS232-KIT is an accessory for the Atlona Velocity™ Control System that

provides conversion between IP and RS-232 control commands. This Velocity Control Converter

is very compact and can be placed anywhere a device requires control and is not IP-capable.

The VCC-RS232-KIT is remotely powered through Power over Ethernet (PoE), or locally from a

USB power source. The primary unit installs onto any surface via a convenient mounting dock. A

simple “click” locks it into place for a secure, reliable installation. An RS-232 gender changer is

included.

1 x AT-VCC

1 x AT-VCC-RS232

Package Contents

Operating Notes

• The AT-VCC-RS232-KIT is PoE, to power the unit, simply plug it into a PoE compatible

network switch. If the network switch is not PoE capable, a PoE injector (purchased separately)

or USB can be used.

• All devices (AT-VCC, Velocity, AT-VTP, switchers, etc) should be set to static IPs or the

DHCP IP address reserved for each individual device.

IMPORTANT: Velocity Gateway (AT-VGW-HW) must be set up before the AT-VCC-RS232-

KIT is fully functional.

Installation Guide

AT-VCC-RS232-KIT

16 2 3 4 5

1 Ethernet

Connect an Ethernet cable from this

port to the same network as the Velocity

Gateway .

2 USB

Not used at this time.

3 3.5mm Port

Connect to a VCC RS-232 3.5mm

connector.

4 RS-232 Connector

Connect the RS-232 connector into the

RS-232 port of the controlled device.

5 3.5mm Connector

Connect the 3.5mm connector to the

3.5mm port of the VCC.

6 Factory Reset Button

Press and hold this button to reset all

settings to the factory default.

Panel Description

RS-232

The VCC RS-232 comes with a 3.5mm to DB9 adapter. To ensure the signal passes correctly,

verify the pins match the device connecting to. The pin out is found below.

Pin 2 - RX

Pin 3 - TX

Pin 5 - Ground

Pin 7 - RTS

Pin 8 - CTS

Pin 4 - DTR

Pin 6 - DSR

Data Data Flow Control Modem Control

GND

RXTX

NOTE: Do not alter or cut the RS-232 3.5mm cable in any way. The cable is

proprietary and is the only compatible 3.5mm connector for the VCC.

Installation Guide

AT-VCC-RS232-KIT

The AT-VCC is set to DHCP by default. If the network does not support DHCP, it will

automatically set the AT-VCC to the static IP of after 30 seconds.

192.168.1.70

VHelp and webGUI

Velocity will nd the VCC when scan network is used, but if the VCC needs to be set up o site

rst, the software VHelp can be used.

1 Connect the RS-232 connector into the 3.5mm port on the unit.

2 Connect the AT-VCC to a network switch (PoE is best if a PoE switch is not available, a

power injector or mini USB to USB cable may be used).

3 Download VHelp from the resource tab of https://atlona.com/product/AT-VCC-RS232-KIT.

4 Unzip the le to the local PC

5 Double-click the VHelp executable to open the program. Vhelp will start discovery as soon

as the program is opened.

6 Double click on the VCC (to determine the correct one, look on the bottom of the VCC for

the MAC address). The PC default browser will open to the AT-VCC webGUI.

7 Select Network Settings to open the IP conguration page.

8 Select the DHCP Enabled header, this will disable DHCP and allows IP settings to be edited.

9 Type in the IP details to

match the network details

of the Gateway. e.g. If the

Velocity gateway is located at

the IP of 192.168.12.15, then

the VCC should be set to an

IP within the 192.168.12.XXX

range that has not already

been used.

10 Press the Save Changes button.

Product specificaties

Merk:	Atlona
Categorie:	Niet gecategoriseerd
Model:	AT-VCC-RS232-KIT
Kleur van het product:	Zwart
Gewicht:	40 g
Breedte:	15.24 mm
Diepte:	32.51 mm
Hoogte:	55.88 mm
Intern:	Nee
Hostinterface:	RJ-45
Output interface:	RS-232