Atlas FAP6260T Handleiding

Atlas Speaker FAP6260T

Lees hieronder de 📖 handleiding in het Nederlandse voor Atlas FAP6260T (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 76 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Ceiling Material up to 2"

Tile Bridge

Auxiliary Suspension int Po

Dogleg In Inverted sition Po

FAP6260T

Installation Instructions

ATS004631 RevA 7/13

FAP6260T

Installation Instructions

Mounting Template

9⁄16

" Diameter

The Atlas Sound Strategy Series® III assembly mounts easily into existing

construction drop ceiling or drywall materials.

Drop Tile Ceiling Installation

1. Remove 2' 2' or 2' 4' tile. x x

2. Align adjustable dual rail -ring assembly on rear of tile in& C

desired position.

3. Using template provided mark cut out circle with marker and cut hole. the ,

(99⁄16" FAP6260T)

4. Affix -ring assembly to rails using screws provided and position assembly on rear of ceiling tile. C

Replace tile into grid formed ends of tile bridge rails engage T-bar tile support rails.. Ensure

5. Bring service loop from rear of tile, through tile bridge C-ring to access panel located on of the / the top

enclosure. Terminate the service loop to Phoenix style connector provided (please note polarity).

6. Insert enclosure through front of tile. Using standard #2 Phillips screwdriver or screw-gun,

tighten four dogleg assemblies

until they engage C-ring assembly. the DO NOT OVER-TIGHTEN DOGLEG SCREWS!

7. Adjust front mounted switch to desired tap setting or 8power Ω* (See important note regarding 8 operation)Ω

8. Place grille on front of unit by aligning the tabs on the underside of grille with the notches on the unit bezel.

Allow magnets to hold the grille while rotating to lock the securing tabs.

9. For safety and seismic considerations a suspension ring is integrated into input panel section of unit. the

Atlas Sound strongly suggests that a support wire be installed from this support point to a suitable anchor point above ceiling grid.

In drop tile applications, this wire can usually be installed from an adjacent tile access near speaker location.

Dry Wall ("Hard Deck") Installation

1. Using the template provided, mark cut out circle in desired mounting location and cut hole. ( 9 9⁄16" FAP6260T)

2. Place tile bridge rails and C-ring through hole. Use V shaped edge of C-ring to align tile bridge assembly above ceiling-

(alignment screws provided are not required for this type of installation)

3. Bring service loop from rear of tile, through the tile bridge / C-ring to access panel located on side of the enclosure. Terminate service loop to the

Phoenix style connector provided (please note polarity).

4. Insert enclosure into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten dogleg assemblies until they engage the C-ring assembly.four

DO NOT OVER-TIGHTEN DOGLEG SCREWS!

5. Adjust front mounted switch to desired tap setting or 8power Ω* (See important note regarding 8 operation)Ω

6. Place grille on front of unit by aligning the tabs on the underside of grille with the notches on the unit bezel.

Allow magnets to hold the grille while rotating to lock the securing tabs.

NOTE: Doglegs will accommodate ceiling material thickness up to 1

1⁄2" as shipped from factory. For thicker ceiling materials (up to 2") simply unscrew and flip doglegs

as shown. DO NOT OVER-TIGHTEN DOGLEGS IN EITHER CONFIGURATION!

NOTE: UL recognized conduit clamp must be used for conduit connections. Cable connection cavity is not intended to be used as a junction box.

NOTE: *DO NOT USE 8 SETTING WITH 70.7V / 100V SYSTEMS! *DO NOT OVERPOWER IN 8 CONFIGURATION! Ω Ω

AMPLIFIER OUTPUT SHOULD NOT EXCEED 60 W RMS @ 8 PER SPEAKERΩ

15W @ 70.7V

Full nge Ra

15W @ 70.7V

Full nge Ra

15W @ 70.7V

FAP6260T-B FAP6260T-BFAP6260T-BFAP6260T-B

Full nge Ra

15W @ 70.7V

Full nge Ra

Tap wer Total: 60 Po Watts

Typical 120 tt 70.7V Output Wa

Typical rallel Hookup of Full Range 70.7V/100V SpeakersPa

1 4 5 as er o

Amplifier

Input

- + - + - + - +

Ceiling Material up to 1-1/2"

Auxiliary Suspension int Po

Tile Bridge

Dogleg In Normal Position

ATS004631 RevA 7/13

Grille tabs aligned with

notches on the unit bezel

Grille tabs secured to the

unit bezel

Product specificaties

Merk:	Atlas
Categorie:	Speaker
Model:	FAP6260T
Kleur van het product:	Wit
Gewicht:	566 g
Diepte:	205 mm
Connectiviteitstechnologie:	Draadloos
Gemiddeld vermogen:	- W
Aantal luidsprekers:	1
Aantal per verpakking:	1 stuk(s)
Impedantie:	8 Ohm
Speaker plaatsing:	Plafond-montage
Aantal drivers:	1
Woofer:	Ja
Diameter driver subwoofer (imperiaal):	6 "
Diameter driver:	279 mm
Frequentiebereik:	63 - 15000 Hz
Gevoeligheid:	92 dB
Aantal woofer drivers:	1
Inbouwdiepte:	197.7 mm