Atlas Sound FM250-70 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Atlas Sound FM250-70 (3 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
9 AtlasSound.com
Specifications are subject to change without notice.
Owner’s Manual F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 Fax: 800.765.3435
FM250-4 and FM250-70 Module Features
1. Module Status Indicators
Note: They also parallel Status LED on the front panel of the F6-MF panel.
Ready This LED will illuminate Green when an FM250 power module is installed on the appropriate channel and the F6-MF is
turned on.
Signal The channel Signal LED will illuminate Green when the FM250 amplifier output signal produces a minimum 1 Watt
output.
Limit The Limit LED will illuminate Yellow under load conditions. If the FM250 function switch is set to Limit then the LED
acts as a maximum level indicator. If the FM250 channel Limit function is off, the LED reacts as a Clip indicator. Also,
under Low Impedance loads, this LED serves as a current Limit indictor.
Protect The Protect LED will illuminate Red during one the following conditions. No output will occur while this LED is
illuminated. It will reset itself after the condition has been corrected.
1) Shorted speaker output.
2) Thermal Shut Off. The Temp F6-MF TEMP LED will also be illuminated.
3) Current Overdrive. If the amplifier channel is driving too low of a speaker load.
2. Speaker Connections
A removable Phoenix/Euro Block type connector is supplied to connect your speakers to the FM250 amplifier module. It is
recommended to use 16-gauge wire or lower for connection to the speakers. Do not overload the amp by connecting too many Note:
speakers to the amp.
Protect
Limit
Signal
Ready
Speaker Output
Class 2 Wiring
4Ω
FM250 - 4
250W @ 4Ω
Protect
Limit
Signal
Ready
Speaker Output
Class 2 Wiring
70V
FM250 -70
250W @ 70V
AtlasSound.com 10
Specifications are subject to change without notice.
Owner’s Manual
F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 Fax: 800.765.3435
FM250-4 & FM250-70 Function Switch
FM250 Module Dip Switch Functions are located near the rear of the FM250 modules. It is essential to preset your setting prior Note:
to inserting the module into the F6-MF.
Factory Dip Switch Presets
Dip Switch 1 ships in theOn position. Dip Switches 2 & 3 ship in the Offposition.
Dip Switch 1, Gain
When placed in the “Onposition the channel’s Gain or Input Sensitivity will be 1V (0dBV) for rated output. When placed in the “Off
position the Gain is set to 2V (6dBV).
Dip Switches 2 & 3, HPF
The High Pass Filter (HPF) when placed into the “Onposition engages a 100Hz / 12dB filter. When in the “Offposition the module
operates at full audio bandwidth.
11 AtlasSound.com
Specifications are subject to change without notice.
Owner’s Manual
F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 Fax: 800.765.3435
FM250 Amplifier Module Installation
Use the following steps and read all steps prior to installation.
1. Turn F6-MF AC Power Switch to the “Off” position.
2. Turn down all level controls on the front panel.
3. Remove the blank card slot cover. Do not discard the two screws, you will need them later.
4. Set the function switches on the FM250 module. (See Page 10)
5. Carefully and slowly guide the module into the slot with the PCB components facing to the right. The module heatsink Note:
top and bottom metal edge mate with the mainframe plastic card guides. Do not force the card. Realign if necessary.
6. After the module is pushed in and in contact with the back plane of the PCB assembly mating connector, firmly press the
module in completing the connection. If the module plate is flush to the F6-MF, the module is fully seated.
7. Insert the two screws from the cover pate. Some minor alignment may be required.
Align Modules to
Top & Bottom Card
Guides


Product specificaties

Merk: Atlas Sound
Categorie: Receiver
Model: FM250-70

Heb je hulp nodig?

Als je hulp nodig hebt met Atlas Sound FM250-70 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Atlas Sound

Handleiding Receiver

Nieuwste handleidingen voor Receiver

Devialet

Devialet Astra Handleiding

19 December 2024
Atoll

Atoll IN100 Handleiding

18 December 2024
Atoll

Atoll IN200 Handleiding

18 December 2024
Atoll

Atoll IN80 Handleiding

18 December 2024
Atoll

Atoll AM 00 Handleiding

18 December 2024
Atoll

Atoll DAC200 Handleiding

18 December 2024
Atoll

Atoll AM200 Handleiding

18 December 2024
Atoll

Atoll IN50 Handleiding

18 December 2024