Atlantis Land A08-LS1500-W Handleiding

Atlantis Land Barcode lezer A08-LS1500-W

Lees hieronder de 📖 handleiding in het Nederlandse voor Atlantis Land A08-LS1500-W (4 pagina's) in de categorie Barcode lezer . Deze handleiding was nuttig voor 64 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

How Do You Program Your Scanner?

1.Scan Start Conguration

2.Scan all necessary able for parameters that

Meet your application

3.Scan end conguration to save to save the changes.

Resetting The Standard Product Defaults

If you aren’t sure what programming options are in your scanner,

or you’ve changed some options and want the factory settings

restored, scan the bar code below.

Symbologies setting

Terminator selection

Start Conguration

None * CR + LF

Tab CR

Interface selection

Reading mode

Language ………etc.

End Conguration

Standard Product

Default Setting

* US

* Please scan the following barcode directly with your USB receiver on.

USB Keybaord Language

Itlian

Default setting of wireless scanner

The default setting of wireless scanner is 2425MHz and

power saving with 10min period of time. The default values

can be modied by re-pairing the scanner and USB receiver.

The setting switch and pairing button are located at USB

receiver as shown

Setting switch 1 is associated with

volume of beeper

Setting switch 2 is associated with

frequency

Setting switch 3 & 4 is associated

with power management

Note: Before congure the switch setting, please rst remove the

USB receiver from host computer.

How to pair your scanner and

receiver?

Scanner

USB receiver

** When devices are successfully paired you will hear beeps three

times from scanner and see three bllnks from USB receiver.

Wake up your Atlantis wireless

scanner

Press and release the trigger on your scanner to activate it.

Your scanner is ready to work when blue LED comes on.

Connect USB receiver to a host

computer

The device can be quickly recognized by host computer

without any software/driver installation. Within less than

10 seconds the receiver will double ash blue to inform the

Initialization is completed.

Recharging the battery

The Red LED comes on when the battery level is low, please

recharge the scanner immediately. When the scanner is

charging, the LED is green (solid). A full recharge (from

completely drained battery) takes approximately 4 hours.

When the scanner is fully charged, the green LED will go off.

Scanner LED indicator

USB receiver LED indicator

Before Getting Started

Open the package and check every accessory

About your Atlantis wireless scanner

KC-3200ZB is one on one wireless data communication

protocol. The scanner is already paired with the USB receiver. Just

easily plug USB receiver and start the operation. The

scanner on a real time basis, if the scanner is connected, the

barcode is decoded and transmitted to the remote host without

any delay. If the scanner is not connected or out of range, the data

is lost (status: 4 beeps)

Note:

New batteries should be fully charged before their rst use

Wireless Scanner

USB docking station

USB Receiver

USB recharge cable

Status / indicator

Good Scan

Transmission

failure

Low battery

Recharge

Operation mode

Sleeping

Color

Red

Beeper

1 beep

4 beeps

None

Indication

LED will ash to present the success of transmision

Blue LED

1 blink

None

Green LED

None

Red LED

Noe

OFF

Volume of beep

Low

High

OFF

Frequency

2480MHz

2425MHz

OFF

Power saving (sleep mode)

switch off after 10min.of inactivity

Scanner is always on

switch off after 30min.of inactivity

switch off after 1min. of in activity

In 1 second

In 5 second

In 2 second

In 1 second

In second

Press and hold the trigger for 10 sec. release the

trigger after hearing 1 beep

Piease quick press the trigger for 10 times

within five (5) sec. in order to put the scanner in

pairing mode.

The scanner will beep every second when stay in

paring mode (for about 45 seconds.)

Press and hold the pairing button for 10 sec.

release the button after seeing red LED ashing.

Please quick press the pair bottom for 10 times

within five (5) sec.in order to put the scanner in

pairing mode.

in pair mode, the USB receiver will blink every

second (for 25 xeconds)

Product specificaties

Merk:	Atlantis Land
Categorie:	Barcode lezer
Model:	A08-LS1500-W
Kleur van het product:	Zwart
Gewicht:	195 g
Materiaal behuizing:	Kunststof
Oplaadtijd:	4 uur
Capaciteit van de accu/batterij:	1260 mAh
Type beeldsensor:	Laser
Ingangsspanning:	5 V
Temperatuur bij opslag:	-20 - 60 °C
Frequentie:	2400 - 2500 MHz
Golflengte:	650 nm
Stroomverbruik:	220 mA
Standaard interfaces:	USB
Maximale afstand:	100 m
Afmetingen (B x D x H):	68 x 160 x 88 mm
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 85 procent
Batterijtechnologie:	Lithium-Ion (Li-Ion)
Lichtbron:	LaserDiode
Aantal lezingen per inzet:	60000
Lees-snelheid (max):	100 lezingen/s
Decoding standaarden:	UPC/EAN\nCodabar\nCode 39\nCode 93\nCode 128, \nIndustrial 2of5\nInterleave 2of5\nMatrix 2of5\nMSI/Plessey\nCode 11\nCode 32\nChinese Post\nTelepen\nGS1 Databar\nItalian Pharmacy
Scannerresolutie:	0.1016 mm