Atdec TH-VA-2X2-NECX-463 Handleiding

Atdec Nicht kategorisiert TH-VA-2X2-NECX-463

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec TH-VA-2X2-NECX-463 (5 pagina's) in de categorie Nicht kategorisiert. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

Rev.02-06/25/12

2 Wide x 2 Deep Video Wall Display (Rear View)

This display kit mounts the NEC X463UN

LCD monitor in a 2 wide by 2 deep landscape

configuration. The frame attaches to a wall and

receives the LCD monitors by way of four machined

fittings (per monitor) that thread into the monitor’s

VESA holes. These fittings then insert into the frame’s

channels. The monitor’s fittings secure to the frame

with locking arms that provide an easy way to remove

the monitors for service. A removable panel provides

access for media players behind the frame.

Important: Installing video displays is a serious

endeavor that requires experienced professionals.

Improperly prepared walls and other structures as

well as the equipment being installed can result in

property damage, injury and/or liability to the

installing contractor. Do not proceed if any part of

the installation is in doubt.

Caution: Due to the wide variety of structures,

environments, materials and installation methods, the

installing contractor must exercise good judgment in

selecting the proper mounting area. The mounting

structure must be capable of supporting at least 5

times the load of the installed equipment. Consult local

building codes for further guidance.

Follow these instructions for the most efficient and

safest mounting results.

Package Contents:

1 pc Frame w/ locking arms assembled

2 pcs Media player mounting bracket

1 pc Adjustment wrench

16 pcs M6 Threaded stand-off button (black)

9 pcs Wood Screw Hanger (Adjustable Lag bolts)

9 pcs Flat washer, 5/16

9 pcs Hex nuts, 5/16-18

1 pc Instruction sheet

Notes:

Hardware to mount frame to the wall are included.

Note:

The assembled frame weighs approximately 65 lb/29.5 Kg and requires just one installer. Two installers recommended for installing the

LCD monitors.

Installation Instructions

TH-VA-2X2-NEC X463

Video Wall 2x2

Rev.02-06/25/12

Figure 1

Figure 2

Step 1: Mount Frame to Wall

Scribe a horizontal line on the

wall showing the exact location

of the top edge of the upper left

LCD monitor will be. Measure

down 8.8” (223.5mm) from that

line and scribe another

horizontal line showing where

the first location of the

adjustable lag bolts for the

mounting frame will be. This is

for the top left keyhole slot

(Figure 1).

Scribe a vertical line showing

where the left side of the upper

LCD monitor will be. Measure to

the right and scribe another

vertical line 12.6” (320mm) to

locate the location of the first

adjustable lag bolts for the

mounting frame will be. This is for the top right keyhole slot

(Figure 1).

Mark where the 2nd horizontal line vertical lines meets.

Measure 55.7” (1414.8mm) to the right for next location of the

adjustable lag bolt. Use a level then mark the second location,

use level to make sure it Is horizontally level to the first hole

on the left side. Pre-drill the marked locations using a 3/16”

(5mm) drill (Figure 1).

Install the adjustable lag bolts to the pre-drilled holes then

hang the frame onto the two adjustable studs. Install the flat

washer and hex nut to secure frame to wall. Hand tighten hex

nut only (Figure 2).

Step 3:

Mark the location for the other adjustable lag

bolts, one upper center keyhole, three bottom

keyholes slots and three center middle holes

(Figure 3).

Step 4:

Remove the two nuts and washer securing the

frame to the wall and place the frame back on

the floor. Pre-drill all the marked locations

using 3/16” drill bit then install the adjustable

lag bolts (Figure 3 and 4).

Step 5:

Figure 3

Rev.02-06/25/12

Figure 6

Figure 7

Re-place the frame on the wall then secure using the provided hex

nut and flat washer. Hand tighten hex nut only (Figure 4).

Step 6:

Using a 4 or 5 feet long level plum the frame by adjusting the

adjustable lag bolts on the vertical channels counter clockwise to pull

the frame frontward. Use the provided adjustment wrench to rotate

the adjustable lag bolts. Use the level or straight edge to make the

H-slat horizontally straight by adjusting the adjustable lag bolt closest

to the H-slat (Figure 5).

Step 7:

Once the frame is plummed and level tighten the hex nuts

permanently.

Step 8: Install Brackets to Media Player

Attach the media player brackets to the sides of the media

player using its existing side screws (Figure 6).

Step 9: Install Media Player

Choose and remove the bottom left or right lower H-slat frame by

unscrewing its flat head screws Install the media player to (Figure 7).

the wall between the two vertical channels using the appropriate fasteners

through the media player’s brackets Re-install the bottom (Figure 7).

lower H-slat.

Figure 4

Figure 5

Product specificaties

Merk:	Atdec
Categorie:	Nicht kategorisiert
Model:	TH-VA-2X2-NECX-463

Heb je hulp nodig?

Als je hulp nodig hebt met Atdec TH-VA-2X2-NECX-463 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Nicht kategorisiert Atdec

Atdec TH-VA-2X2-NECX-463 Handleiding

29 Juni 2023

Handleiding Nicht kategorisiert

Nieuwste handleidingen voor Nicht kategorisiert

Technaxx TX-182 Handleiding

9 Juli 2023

Lincoln Electric Maverick 325X Handleiding

8 Juli 2023

Cherry MultiBoard G81-8000 Handleiding

7 Juli 2023

Conair SWJ1 Interplak Handleiding

6 Juli 2023

Ade CK 2112 Handleiding

5 Juli 2023

QUIO QU-950-4-HF-2.0 Handleiding

5 Juli 2023

VAX Rapide Deluxe Pre-Treatment V-026PTS Handleiding

30 Juni 2023

Melinera 101074-14-01 Handleiding

26 Juni 2023

American BioTech Supply ABT-HC-UCFS-0504W Handleiding

21 Juni 2023

Supermicro SuperServer SSG-640SP-DE2CR90 Handleiding

21 Juni 2023