ART USB Dual Pre Project Series Handleiding

ART Hifi systeem USB Dual Pre Project Series

Lees hieronder de 📖 handleiding in het Nederlandse voor ART USB Dual Pre Project Series (12 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
USB Dual Pre
User’s Manual
IMPORTANT SAFETY INSTRUCTION – READ FIRST
This symbol, whenever it appears, This symbol, wherever it appears, alerts you
alerts you to the presence of uninsulated to important operating and maintenance
dangerous voltage inside the enclosure-voltage instructions in the accompanying literature.
that may be sufficient to constitute a risk of shock. Please read the manual.
Read instructions:
Retain these safety and operating instructions for future reference. Heed all warnings printed here and on the
equipment. Follow the operating instructions printed in this user manual.
Do not open:
There are no user serviceable parts inside. Refer any service work to qualified technical personnel only.
Power sources:
Connect the units power supply to mains power only of the type described in this user manual or marked on
the power supply.
Power supply:
Use the power supply with sealed mains plug appropriate for your local mains supply as provided with the
equipment. If the provided supply does not fit into your outlet consult your service agent. Route the power cord
so that it is not likely to be walked on, stretched or pinched by items placed upon or against it.
Grounding:
Do not defeat the grounding and polarization means of the power supply.
Moisture:
To reduce the risk of fire or electrical shock do not expose the unit to moisture or use in damp or wet condi-
tions. Do not place container of liquid on unit.
Heat:
Do not locate the unit close to excessive heat or direct sunlight, as this could cause a fire hazard. Locate the
unit away from any equipment, which produces heat such as: power supplies, power amplifiers and heaters.
Environment:
Protect from excessive dirt, dust, heat, and vibration when operating and storing. Avoid tobacco ash, drink
spillage and smoke, especially that associated with smoke machines.
Handling:
Protect the controls from damage during transit. Use adequate padding if you need to ship the unit. To avoid
injury to yourself or damage to the equipment, take care when lifting, moving, or carrying the unit.
Servicing:
Unplug power immediately if equipment is exposed to moisture, the power supply becomes damaged during a
lightning storm or if smoke odor or noise is noted. Refer servicing to qualified technical personnel only.
Installation:
Install the unit in accordance with the instructions printed in the user manual.
INTRODUCTION:
The USB Dual Pre is a full-featured high quality dual portable preamplifier and computer interface
packed into a compact rugged case. It is designed to work over a wide variety of applications from
remote field recording to desktop/studio tracking. Each of the two low noise input channels has up to
48 dB of clean gain with signal present and clip LED indicators. Inputs can be either XLR balanced or
1/4-inch TRS. Each of the 1/4-inch TRS outputs is buffered low impedance balanced.
The USB Dual Pre can be externally powered from the mains via a wide range of external power
adapters, or from an internal 9 Volt battery, or from the USB bus itself, or any combination of these
power sources. When running off of the battery alone, you should get in excess of 50 hours of opera-
tion when phantom power is off. Battery life drops to around 20 hours (depending on microphone)
when phantom powering from the battery alone (still enough time to get through a session).
The built-in low noise +48 Volt phantom power supply allows you to power up to 2 microphones as
well as the preamplifier when running from any power sources including the USB bus.
For monitoring, an 1/8-inch TRS mini headphone jack with level and monitor mix controls on the rear
allow for latency free local monitoring of the inputs while recording as well as playback monitoring of
the USB bus. The monitor mix is also routed to the ¼-inch TRS balanced outputs. This lets you use
the 1/4-inch outputs as either a preamplifier out or as the monitor feed to your powered monitors.
The USB interface is fully compliant with the USB 1.1 specification and uses USB adaptive mode for
playback and USB asynchronous mode for record. It will work with the USB audio device drivers built
into Windows 98SE/ME/2000/XP/Vista 32bit and Apple OS9.1/OSX computers with native USB
support. No special drivers are needed.
The compact black anodized all aluminum case with rubber sides makes for a rugged design. The
USB Dual Pre will provide years of trouble free service and its high quality audio channels and
versatile powering options make the USB Dual Pre the obvious choice in a wide variety of applica-
tions from Podcasting/Broadcasting to Tracking and Monitoring.
With the USB Dual Pre, your laptop, and a pair of quality microphones you can do some serious
remote recording.
Key Features Include:
USB Connectivity to Desktop and Laptop Computers
Low Noise Fully Balanced XLR and 1/4-inch TRS “Combo” Inputs
Up to 48 dB of Clean Gain
Built-in Low Noise +48 Volt Phantom Power Supply
Latency Free Monitoring Mix and Level Controls
Independent Channel Gain Controls
1/4-inch TRS Balanced Monitor and 1/8-inch Headphone Monitor Outputs
Includes Recording & Production Software
Compact, Stackable all Aluminum Chassis
Flexible 3-way Power from USB, External Supply, or 9 Volt Battery


Product specificaties

Merk: ART
Categorie: Hifi systeem
Model: USB Dual Pre Project Series

Heb je hulp nodig?

Als je hulp nodig hebt met ART USB Dual Pre Project Series stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Hifi systeem ART

Handleiding Hifi systeem

Nieuwste handleidingen voor Hifi systeem