Argox AS-8150 Handleiding

Argox Barcode scanners AS-8150

Lees hieronder de 📖 handleiding in het Nederlandse voor Argox AS-8150 (123 pagina's) in de categorie Barcode scanners. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/123

NOTICE:

This equipment has been tested and complied with

the limits for a Class a digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to

provide a reasonable protection against harmful

interface when the equipment is operated under a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful interface to

radio communications. Operation of this equipment in

a residential area is likely to cause harmful interface in

which case the user will be required to correct the

interface at his own expenses.

Note: All brands and trademarks shall belong to their

respective owner.

Note: Specification is subject to changes without

notice.

This device complies with Part 15 of the FCC Rules.

Operation shall be subject to the following two

conditions:

(1) This device may not cause harmful interface, and

(2)

This device must accept any interface received,

including interface that may cause undesirable

operation.

Using the ArgoxScan

8110/8120/8150/8250/8310/8312

The ArgoxScan can automatically scan barcode at a distance.

Simply aim and pull the trigger. Code scanning is performed

along the center of the light bar emitted from the reading

window. This bar must cover the entire code.

Successful scanning shall be obtained by tilting the scanner

with respect to the barcode to avoid direct reflections that

impair the reading performance, especially for 2D barcode.

Recommended Steps

When the required settings have been configured, all settings

are stored in non- volatile memory of scanner after reading

EXIT Label. Recommended steps are as follows.

1) Set right host interface for your scanner.

(The scanner is in factory default shown as bold label)

2) Set interface to optimize protocol of scanner with your

host in interface section.

3) Set system control of scanner, such as specific

adjustments double confirm, power saving, indicator

and scanning mode which you prefer usage in system

control section.

4) Set code options of scanner for your usage in code

option section. You must make sure to enable the

symbology first, then Min./Max. code length, code ID

checksum and truncate digits are also converted.

5) Set string format of the scanner, such as preamble,

postamble Prefix, suffix, code ID and code name

transmission for your application in string format

section.

Note: If still not work properly. Please contact your dealer for

further information.



CONTENTS

Chapter 1 Introduction

Introduction…………………………..……………….

Default Setting ……………………………………….

ArgoxScan8110/8120 specification ………………..

ArgoxScan8150/8250/8310/8312 specification …..

Programming the ArgoxScan…………………….. 10

Chapter 2 Parameter Setting

Interface……………………………………………….…

Interface Selection …………………………………..

Keyboard wedge …………………………………….

RS-232 …………………………………………….….

Wand Emulation …………………………….……….

Pin Assignments …………………………………….

System Control……………………………………….

Scan ………………………………………………….

Indication …………………………..…………………

Code Option…………………………………….………

UPCA ……………………………………..………….

UPCE …………………………………………………

EAN-13 ……………………………………………….

EAN-8 …………………………………………………

Code 39 ………………………………………………

Interleaved 2 of 5 ……………………………………

Industrial 2 of 5 ………………………………………

Matrix 2 of 5 Eur ……………………………………

Codabar ………………………………………………

Code-128 ……………………………………………

Code-93 ………………………………………………

Code-11 ………………………………………….……

MSI/Plessey ………………………………………….

UK/Plessey …………………………………………..

Product specificaties

Merk:	Argox
Categorie:	Barcode scanners
Model:	AS-8150
Kleur van het product:	Wit
Gewicht:	160 g
Soort:	Draagbare streepjescodelezer
Materiaal behuizing:	Rubber
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Type stroombron:	USB
Meegeleverde kabels:	USB
Stroomverbruik (in standby):	0.6 W
Certificering:	CE, FCC, CCC
Type beeldsensor:	CCD
Duurzaamheidscertificaten:	RoHS
Ingangsspanning:	5 V
Temperatuur bij opslag:	-40 - 60 °C
Golflengte:	660 nm
Stroomverbruik:	255 mA
Ondersteunde streepjescodes (1D):	GS1-128 (UCC/EAN-128)
Standaard interfaces:	USB
Soort scanner:	1D
Stroomverbruik (typisch):	1.275 W
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 90 procent
2D ( matrix en gestapeld ) barcodes ondersteund:	PDF417
Licht niveaus (direct zonlicht):	0 - 60000 Lux
Yaw lees-hoek:	0 - 75 °
Lees-snelheid (max):	200 lezingen/s
Werkafstand:	250 mm
Optische sensorresolutie:	2048 Pixels
Maximale scan breedte:	120 mm