Apc BE325-UK Handleiding

Apc Server BE325-UK

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BE325-UK (2 pagina's) in de categorie Server. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Connect Equipment

SurgeArrest® Surge Protector

User’s Manual

Connect Battery

Power On

All other trademarks are property of their respective owners.

The APC SurgeArrest Surge Protector + Battery Backup is shipped with the battery disconnected. The unit will not operate until the battery is connected.

NOTE: Small sparks may occur during battery connection. This is normal.

Surge Protection

These outlets provide full-time protection from surges even if

the unit is switched OFF. Plug your printer, fax machine,

scanner, or other peripheral that does not need battery power

into these outlets.

Battery Backup + Surge Protection

These outlets are powered whenever the unit is switched ON.

During a power outage or other utility problems (brownouts, over-

voltages), these outlets will be powered for a limited time by the

internal battery. Plug your computer and 17” (or smaller) monitor,

into these two outlets.

Connect FAX/Modem/Phone

The unit protects a single line (2-wire) fax, modem or phone from surges when it is

connected as shown below.

Connect AC Line Cord

Connect the AC line cord to a 230-volt outlet.

The Surge Protector + Battery Backup should be

allowed to charge for at least 16 hours to ensure

sufficient runtime. The unit is being charged

whenever it is connected to utility power, and the

unit is turned ON.

Power ON the unit by pressing the ON/OFF button.

Turn on your equipment.

The Surge Protector + Battery Backup provides status indications through the flashing

of the “Power On” indicator, as well as audible beeps. The indications are as follows:

Status Visual Indications Audible

Indication

Alarm Terminates

When

On Line - Unit is supplying

conditioned utility power to your

equipment

Power On LED - ON None n/a

On Battery - Unit is supplying battery

power to the equipment connected to

the battery powered outlets

Power On LED - ON

(off during beep)

Beeping 4 times

every 30 seconds

Unit returns to an On

Line status or when

the unit is turned off.

Low Battery Warning - Unit is

supplying battery power and the

battery is nearly depleted. Once

depleted, the unit will turn off.

Power On LED -

Flashing

Rapid beeping

(one second

intervals)

Unit is turned OFF,

returns to On Line or

when the battery is

finally exhausted and

the unit turns off.

Replace Battery - Battery may need

to be replaced, or the battery is not

connected.

Power On LED -

Flashing

Continuous tone. Unit is turned OFF

and then ON and it

passes a subsequent

battery test. (This test

occurs automatically

whenever the unit is

turned ON and every

14 days)

Overload Shutdown - During On

Battery operation a battery-power

outlet was overloaded.

Power On LED -

OFF

Continuous tone. Unit is turned off

using the ON/OFF

button.

Status Indications

Telephone Wall

Fax/Modem/Phone

+ Battery Backup (BE325-UK)

32 - 104

F (0 - 40

Note: The on/off switch is illuminated when in the ON position.

The switch may flash to indicate changing power conditions

(see Status Indications).

Circuit

Breaker

AC Line

Cord

230-Volt Wall

Outlet

.apc.com

Battery Backup plus Surge Protection

Surg e P ro te cti on

Side View

Top View

Push to Reset

Circuit Breaker

RJ-11

Connectors

End View

Top View

Battery Backup plus Surge Protection

134

.apc.com

Surge Protector

+ Battery Backup

325VA

.apc.com

Surge Protector

+ Battery Backup

325VA

Troubleshooting Consult APC Online Technical Support or call APC Technical Support for assistance with problems that cannot be resolved using the table below:

Unit will not turn on.

Connected equipment loses power.

The power On button is lit and the unit is

beeping four times every 30 seconds.

The power On button flashes once per

second and the unit beeps once per second

at the same time.

Inadequate runtime.

Battery is disconnected.

Circuit Breaker has tripped.

Utility power not available at the wall outlet.

Equipment is connected to the “Surge Protection” outlets.

The unit is overloaded.

The unit has exhausted its available battery power.

Connected equipment does not accept the step-

approximated sine waveform the unit.

The unit may require service.

The unit is using battery.

Battery capacity is low (about 2 minutes of use remaining).

The battery is not fully charged.

Battery is near the end of useful life.

Problem Probable Cause Solution

Specifications

Warranty

Service

Contact Information

Voltage 230 Vac Nominal

Acceptable Input Frequency 47 - 53 Hz

Low-Voltage Transfer Point (when unit

starts operating on battery)

180 Vrms

High-Voltage Transfer Point 266 Vrms

Battery Back-up Capacity (2 outlets) 325 VA/185 W

Surge Protection Capacity (4 outlets) 4 Amps (includes battery-powered outlets)

Voltage (on battery power) 230 Vrms + 8%

Frequency (on battery power) 50 Hz + 1 Hz

Transfer Time to Battery 5 ms typical

AC Surge Protection Full time, 1800 eP Joules (battery-powered outlet)

Telephone Line Surge Protection Single line (2-wire) analog (RJ-11C)

EMI/RFI Filter Full time

Input Overload Protection Resettable circuit breaker (4A)

Battery Type Sealed, maintenance-free lead acid

Recharge Time 8 to 16 hours typical from total discharge

Average Life 2 - 4 years depending on the number of discharge cycles and

environmental conditions

Net Weight 8.8 lb (4 kg)

Size 3.74”H x 4.52”W x 14.3”D (95mm x 115mm x 364mm)

Operating Temperature 0 to 40oC (32 to 104oF)

Storage Temperature -15 to 45oC (5 to113oF)

Operating Relative Humidity Operating Relative Humdity: 0 - 95%

Operating Elevation 0 - 10,000 ft (0 to 3000m)

Safety Approvals CE per IEC60950 and EN50091-1-1

EMC Compliance EM50091-2/EN55022 Class B

Item Specification

The standard warranty is 2 years from the date of purchase. APC’s standard procedure is to replace the

original unit with a factory reconditioned unit. Customers who must have the original unit back due to

assigned asset tags and set depreciation schedules must declare such a need at first contact with APC

Technical Support. APC will ship the replacement unit once the defective unit is received by the repair

department or cross-ship upon the provision of a valid credit card number. The customer pays for shipping

to APC, and APC pays ground freight transportation costs back to the customer.

Please DO NOT RETURN the unit to the place of purchase under any circumstances.

1. Consult the Troubleshooting section to eliminate common problems.

2. Verify the battery is connected (see Connect Battery) and that the Circuit Breaker is

not tripped (see Troubleshooting section).

If you still have problems or questions, please contact APC via the internet or at one

of the phone numbers listed below.

3. Before contacting APC, please be sure to record the date purchased, model and

serial number (on bottom of unit).

4. Be prepared to troubleshoot the problem over the telephone with a Technical

Support Representative. If this is not successful, the representative will issue a

Return Material Authorization Number (RMA#) and a shipping address.

5. Pack the unit in its original packaging. If the original packaging is not available, ask

APC Technical Support about obtaining a new set. Pack the unit properly to avoid

damage in transit. Never use foam beads for packaging. Damage sustained in transit

is not covered under the warranty (insuring the package for full value is

recommended).

6. Write the RMA# on the outside of the package.

7. Return the unit by insured carrier to the address given to you by APC Technical

Support.

Internet http://www.apc.com

Email http://www.apc.com/support

APC Germany 0800 180 12 27

APC Czech and Slovak Republics 0900 102063

Worldwide +1.401.789.5735

American Power Conversion 32 Fairgrounds Road

West Kingston, RI 02892

Order Replacement Battery

Replace with an APC qualified battery (RBC47). Replacement batteries can be ordered from

www.apc.com or by calling APC Technical Support (valid credit card required). Have your unit model

number available when ordering. Your model number can be found on the bottom of the unit.

Safety

This section contains important instructions that should be followed during installation

and maintenance of the APC equipment and batteries. It is intended for APC

customers who setup, install, relocate, or maintain APC equipment.

This equipment is intended for installation in a temperature-controlled indoor area (see

Specifications for exact temperature range), free of conductive contaminants.

Connect the battery (see Connect Battery).

Reduce the amount of equipment plugged into the “Battery Backup + Surge

Protection” outlets. Reset the Circuit Breaker by pushing it back in.

Reduce the amount of equipment plugged into the “Surge Protection” outlets. Reset

the Circuit Breaker by pushing it back in.

Ensure that the fuse or circuit breaker for the outlet is okay, and that the wall switch

controlling the outlet (if any) is in the ON position.

Ensure that the equipment you want to stay powered during a power failure is

plugged into the “Battery Backup + Surge Protection” outlets and NOT the “Surge

Protection” outlets.

Make sure that the equipment plugged into the outlets of the unit are not

overloading the capacity of the unit. Try removing some of the equipment and see if

the problem continues.

The unit can only operate on battery power for a limited amount of time. The unit

will eventually turn off when the available battery power has been used. Allow the

unit to recharge for 16 hours before continuing use of the unit.

The output waveform is designed for computers and computer-related equipment.

It is not designed for use with motor-type equipment.

Contact APC Technical Support for further troubleshooting.

The unit is operating normally and using battery power. Once On Battery, you

should save your current work, power down your equipment, and turn the unit OFF.

Once normal power is restored, you may turn the unit back ON and power your

equipment.

The unit is about to shut off due to a low battery charge condition! When the unit

beeps once every second, the battery has about 2 minutes of power remaining.

Immediately power down your computer and turn the unit OFF. When normal power

returns, the unit will recharge the battery.

Allow the unit to charge by leaving it plugged into the wall a full 16 hours.

As a battery ages, the amount of runtime available will decrease. You can replace

the battery by ordering one at www.apc.com. Batteries also age prematurely if the

unit is placed near excessive heat.

Electrical Safety

To reduce the risk of fire, connect only to a circuit provided with 20-amp

maximum branch circuit overcurrent protection in accordance with the

National Electrical Code ANSI/NFPA.

CAUTION! De-energizing Safety

The unit has an internal energy source (the battery); the output may be energized

when the unit is not connected to an AC power outlet.

To de-energize pluggable equipment: switch the unit off. Disconnect the unit

from utility power. Next, disconnect the equipment from the unit. Disconnect

the internal battery (see Connect Battery).

The unit includes a protective earth conductor which carries the leakage

current from the load devices (computer equipment). Total leakage current

must not exceed 3.5 mA.

Use of the unit in life support applications where failure of the unit can

reasonably be expected to cause the failure of the life support equipment or

to significantly effect its safety or effectiveness is not recommended.

WARNING! Battery Safety

• Except for the battery, this unit contains no user-serviceable parts. This

equipment contains potentially hazardous voltages. Do not attempt to

disassemble the unit. Repairs are performed only by factory trained

service personnel.

• Do not dispose of batteries in a fire. The batteries may explode.

• Do not open or mutilate batteries. They contain an electrolyte which is

toxic and harmful to the skin and eyes.

• To avoid personal injury due to energy hazard, remove wrist watches

and jewelry such as rings when replacing the batteries. Use tools with

insulated handles.

• Replace batteries with the same part number and type as originally

installed in the unit.

Replacement and Recycling of Batteries

• See your dealer for information on replacement battery kits and battery

recycling.

Batteries must be recycled. Deliver the battery to an

appropriate recycling facility or ship it to the supplier in

the new battery’s packing material. See the new battery

instructions for more information.

990-2124

Product specificaties

Merk:	Apc
Categorie:	Server
Model:	BE325-UK
Kleur van het product:	Houtskool
Gewicht:	4000 g
Breedte:	360 mm
Diepte:	95 mm
Hoogte:	115 mm
Vormfactor:	Compact
Uitgangsvermogen:	185 W
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	50 Hz
Compatibiliteit:	CE, EN 50091-1, EN 50091-2
Bedrijfstemperatuur (T-T):	0 - 40 °C
Code geharmoniseerd systeem (HS):	85078000
Aantal AC uitgangen:	4 AC-uitgang(en)
Nominale input voltage:	- V
Stopcontacttypes:	BS 1363
Output power capacity:	0.325 kVA
Ingang operation voltage (min):	230 V
Ingang operation voltage (max):	230 V
Uitgang operation voltage (min):	230 V
Uitgang operation voltage (max):	230 V
Netspanning, in bedrijf:	- V