Apart PXQ2215 Handleiding

Apart Receiver PXQ2215

Lees hieronder de 📖 handleiding in het Nederlandse voor Apart PXQ2215 (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 110 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

PXQ2215

OWNER’S MANUAL

SLIMLINE

SLIMLINESLIMLINE

SLIMLINE

• Read all documentation before operating your equipment.

Retain all documentation for future reference.

• Save the carton and packing material even if the equipment has arrived in good condition.

Should you ever need to ship the unit, use only the original factory packing.

• Do not spill water or other liquids into or on the unit.

• Make sure power outlets conform to the power requirements listed on the back of the unit.

• Do not use the unit if the electrical power cord is frayed or broken.

• Always operate the unit with the AC ground wire connected to the electrical system ground.

• Have gain controls on amplifiers turned down during power-up to prevent

speaker damage if there are high signal levels at the inputs.

• Do not connect the inputs / outputs of amplifiers or consoles to any other voltage source,

such as a battery, mains source, or power supply, regardless of whether

the amplifier or console is turned on or off.

• Power down & disconnect units from mains voltage before making connections.

• Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.

• Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an

environment which may distort the normal flow of air around the unit. If the unit is used in an

extremely dusty or smoky environment, the unit should be periodically "blown free" of dust.

• Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages.

• Do not drive the inputs with a signal level greater than that required to drive equipment

to full output.

• Do not run the output of any amplifier back into another input.

• Do not ground the red output terminal, never connect a red output terminal to

another red output terminal.

• In case of mal-function this device should be serviced by qualified service personnel only.

SAFETY INFORMATION

C A U T I O N

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER OR BACK

NO USER-SERVICEABLE PARTS INSIDE

SERVICING ONLY FOR QUALIFIED PERSONNEL

EQUALIZER & X-OVER EQUALIZER & X-OVER

2 X 15, 2/3 & 1/3 ocatve combined

35 - 400Hz adjustable

24dB/oct Linkwitz - Riley

+/- 6dB or 12dB selectable

Balanced XLR 20Kohm, RCA cinch 15Kohm

Sub out / High pass fullrange out : XLR balanced + RCA cinch

0.02% (at 1KHz all sliders at center)

20 Hz to 50KHz

>93dB

44 X 483 X 280 MM

Net. 2.8 Kg

Type

X-over

Control range

Inputs

Outputs

Distortion

Frequency Response

Signal to noise ratio

Dimensions (H x W x D):

Weight

PXQ2215

EQUALIZER & X-OVER

SLIMLINE

SLIMLINESLIMLINE

SLIMLINE

1. Power switch

To turn the unit ON or OFF, press the upper or lower part of this button. The LED above the switch will light to indicate

that the unit is ON.

2. Filter level controls

Each one of these linear potentiometers will boost or attenuate (+/-6dB or +/-12dB) the selected frequency at a preset

bandwith. When all sliders are in the centre position, the output of the equalizer is flat response.

3. Range switch

This button switches the gain range of the filter potentiometer bewteen +/-6dB and +/-12dB, led (6) will be illuminated.

4. Bypass switch

This switch inserts or removes the equalizer channel path. If bypass, the bypass led (7) will be illuminated to indicate it

is in bypass mode. When bypassed, the input signal is routed directly to the cross-over section.

5. Volume

This control sets the signal level of the equalizer.

If there is a signal present at the inputs led (8) will be illuminated.

If the peak led (9) is lights up: turndown this control, lower your input level or reduce the boost level of the equalizer.

10. XLR & RCA inputs

The XLR connectors are actively balanced and are used to input / output the signal.

The RCA connectors are unbalanced.

11. SUB LOW PASS

XLR and RCA output connector. This is the low-frequency output, the cross over freq. can be adjusted with the FREQ

(13) potentiometer. The gain of this output can be adjusted with the GAIN (12) potentiometer.

14. FULL RANGE / HIGH PASS

XLR and RCA output connector. When the FREQ (13) potentiometer is turned fully counterclockwise this output is a

full range output. The FREQ (13) potentiometer can be adjusted to the desired frequency for cross-over operation.

In this way you have a two-way cross-over combined with an equalizer.

15. Ground lift switch

This switch is used to disconnect the signal ground from the main chassis earth. If it is determined that the PXQ2215

is the cause of humm & buzz in your system due to a ground loop, push this switch to the lift position.

16. Fuse holder / AC inlet

This connector is meant for the connection of the supplied main cord.

The fuse can only be changed by a qualified technician.

• X-OVER

HUMM & BUZZ

• If ‘Hum’ or Buzz’ occurs when connecting different inputs, then this is often caused by

‘GROUND or EARTH LOOPS’.

If this is the case, press the audio ground lift (15) button.

876

3 4 51 2

11 12 13 14 15 16

400Hz35Hz

CROSS-OVER

POINT

GAIN

LOW PASS HIGH PASS

Freq.

EXTENDED LOW FREQ. CONTROL STANDARD

SPECIAL FEATURES

EQUALIZER & X-OVER

• GRAPHIC EQUALIZER with more low-Freq. controls

•1 When the FREQ (13) potentiometer is turned fully counterclockwise this output is a full range output.

•2 LOW PASS OUTPUT : This output s are used for subwoofers.

The FREQ (13) potentiometer can be adjusted to the desired frequency for cross-over operation.

In this way you have a two-way cross-over combined with an equalizer.

The output gain can be adjusted (+/-6dB) with the GAIN (10) button.

This to obtain the perfect balance between the low and high speakers.

•3 FULL RANGE / HIGH PASS OUTPUT : This output can also be used for driving small satellite speakers or horns.

Because horn or small speakers cannot reproduce low frequencies,

there is the need to filter these low frequencies out of the audio signal.

This can de done by selecting a low-cut freq. (g.e. 100Hz) with the freq. select potentiometer.

In the output signal (High pass) the freq. below 100Hz will be filtered out,

the signal is now safe to drive small speakers or horns.

Most of the room acoustic problems are caused by frequencies between 40 and 250 Hz.

In this region the PXQ2215 has more controls than a standard 15 bands equalizer.

Product specificaties

Merk:	Apart
Categorie:	Receiver
Model:	PXQ2215
Kleur van het product:	Zwart
Gewicht:	3500 g
Frequentiebereik:	20 - 50000 Hz
Signaal/ruis-verhouding:	93 dB
Afmetingen (B x D x H):	483 x 280 x 44 mm
Totale harmonische vervorming (THD):	0.02 procent