Antec Titan 650 Handleiding

Antec Computerbehuizing Titan 650

Lees hieronder de 📖 handleiding in het Nederlandse voor Antec Titan 650 (7 pagina's) in de categorie Computerbehuizing. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

The high quality of our products is assured by a continuous process of refinement of their

technical features. Therefore, it is possible that your product may differ in some respect from the

descriptions contained in this manual. This is not a problem – it is an improvement. All features,

descriptions, and illustrations contained herein are valid as of the date of publication.

TITAN550 – SERVER CASE

Your case includes a pre-installed TruePower 2.0 (TP2-550EPS12V) power supply, one of the quietest

tested power supplies on the market. All TruePower PSUs feature Antec’s Low Noise Technology,

which allows TruePower to deliver an optimum balance between noise reduction and necessary

cooling. The power supply fans will always run at the lowest speed possible for existing load and

conditions. The result? Your power supply will run considerably quieter than traditional power supplies.

Make sure you turn the switch to the ON ( I ) position before you boot up your computer for the

first time. Normally, you won’t need to switch to the OFF (O) position, since the power supply

includes a soft on/off feature. This lets you turn your computer on and off by using the soft

switch on your computer case. If your computer crashes and you can’t shut it down using the soft

switch, you can switch the main power to the OFF (O) position to clear the problem, then reboot.

The Titan has implemented a newly designed double hinge door, which allows the door to open

up to 270º. The front bezel is easy to remove and replace for easy system installation. Titan550 features

6 individual hard drive trays, cooled by two 92mm fans. These drive trays are front accessible to

further ease system integration or upgrading. Additionally, this case also comes with an adjustable

card guide for long add-in cards.

[Applies only to models designed for sale in the European Union: TruePower 2.0 Series

Power Supply models designed for the EU include Power Factor Correction (PFC) circuitry in

accordance with European standard regulation code EN61000-3-2. By altering the input current

wave shape, PFC improves the power factor of the power supply and results in increased energy

efficiency, reduced heat loss, prolonged life for power distribution, and consumption equipment,

and improved output voltage stability.]

SETTING UP

1. Take the case out of the box. Remove the Styrofoam and the plastic bag. Place the case

upright on a flat, stable surface. The power supply fan should be at the back, facing you.

2. Note (not applicable to models designed for the European Union): Before installation,

check the red voltage switch setting on the power supply. It should match your local voltage

(115V for North America, Japan, etc. and 230V for Europe and many other countries). If

it doesn’t match, please change the setting. If you don’t you could damage your equipment

and void your warranty.

3. Remove the thumbscrews from the right side panel. Slide the panel towards the back of

the case to remove the side panel.

4. Inside the case you should see the power supply, some wiring with marked connectors

(USB, PWR etc.), and installed I/O panel, a power cord and a tool bag containing more

hardware (screws, brass standoffs, etc.), twelve pairs of 3.5" metal drive rails with the rubber

grommets and six pairs of plastic 5.25" drive rails. You need to remove the front bezel in

order to install your 5.25" drives or 3.5" internal drives.

Disclaimer

This manual is intended only as a guide for Antec’s Computer Enclosures. For

more comprehensive instructions on installing your motherboard and peripherals,

please refer to the user’s manuals which come with your components and drives.

5. To remove the front bezel. There are three plastic tabs on the left side of the bezel.

Release them from the top down to detach the bezel from the metal chassis. Swing the bezel

open to about 90º angle and gently lift it upward. The front bezel will come off easily. Set

it in a safe place. In case you need to remove the double hinge door, open the doorNote:

to 90º, and gently press the small plastic tab on the upper hinge. Tilt the door away from

the upper hinge pin, then lift it off the lower hinge pin. Set the door aside in a safe place.

6. To replace the front bezel door. Place the lower hinge slot over the lower hinge pin and

press or rotate the top of the door in so that the tab fully engages with the upper hinge pin.

INSTALLING THE MOTHERBOARD

This manual does not cover CPU, RAM, or expansion card installation. Please consult your motherboard

manual for specific mounting instructions and troubleshooting.

1. Lay the case down, with the open side facing up. The drive cages and power supply should

be visible.

2. Make sure you have the correct I/O panel for your motherboard. If the panel provided

with the case isn’t suitable, please contact your motherboard manufacturer for the correct

I/O panel.

3. Line up your motherboard with the standoff holes, and remember which holes are lined

up. Not all motherboards will match with all the provided holes; this is normal, and won’t

affect functionally. (In other words, there will likely be extra holes.)

4. Lift your motherboard from the standoff holes.away

5. Screw the brass standoffs into the threaded holes that line up with your motherboard. Do

not over tighten the standoffs. Some standoffs may be pre-installed for your convenience.

Note: Consult your CPU cooler’s installation manual before installing your motherboard.

You may need to install a special mounting mechanism first before fastening your

motherboard to the chassis.

6. Place your motherboard on the brass standoffs.

7. Attach your motherboard to the standoffs with the provided Phillips-head screws. Your

motherboard is now installed.

CONNECTING THE POWER AND LED

This Antec TruePower 2.0 (TP2-550EPS12V) power supply is an EPS12V compatible power supply

which comes with a configurable 24-pin Main Power Connector, an 8-pin +12V, and a 4-pin +12V

Power Connector for the motherboard. It also includes four SATA connectors, five to seven

4-pin peripheral power connectors, one to two 4-pin Floppy Drive power connectors, and one

PCI Express graphic card power connector.

1. Connect the 24-pin ATX power connector

(and +12V connectors if appropriate)

to your motherboard.

2. Connect the Reset switch (labeled RESET SW) to

your motherboard at the RST connector. Make

sure the label always faces the front of the case.

3. Power LED (labeled POWER LED) connector is

located behind the Reset connector.

4. Power Switch (labeled POWER SW) connects to the PWR connector on the motherboard.

5. Speaker (labeled SPEAKER) connector is behind the PWR connector.

6. Hard Drive LED (labeled H.D.D. LED) connects to the IDE connector.

7. LED I, LED II connectors: This case comes with two extra LEDs, marked LED I, LED

II. You may use these LED for various purchases such as SCSI LED, Message LED, etc.

Picture 1 Picture 2

For 24-pin

motherboards

For 20-pin

motherboards

Product specificaties

Merk:	Antec
Categorie:	Computerbehuizing
Model:	Titan 650
Kleur van het product:	Zwart
Gewicht:	14000 g
Breedte:	205 mm
Diepte:	584 mm
Hoogte:	446 mm
Soort:	Server
Vormfactor:	Midi Tower
Aantal USB 2.0-poorten:	2
Netvoeding:	650 W
Audio-ingangen:	Ja
Audio-uitgang:	Ja
Soort voeding:	ATX12V v2.0
Aantal IEEE 1394-/Firewire-poorten:	1
Interne schijfposities:	10
Externe drive bays:	4 x 5.25"
Interne drive bays:	6 x 3.5"
Supported motherboard form factors:	ATX
Ventilator(en):	1 x 120mm
Optionele ventilatoren:	1 x 92mm