Antec NSK2480-EC Handleiding

Antec Computerbehuizing NSK2480-EC

Lees hieronder de 📖 handleiding in het Nederlandse voor Antec NSK2480-EC (8 pagina's) in de categorie Computerbehuizing. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

New Solution Series

NSK2480

User’s Manual

Manuel de l’utilisateur

Anwenderhandbuch

Manuale per l’operatore

Manual del usuario

পᡅ䂀ᯢ᳌

At Antec, we continually refine and improve our products to ensure the highest

quality. As such, your new case may differ slightly from the description in this

manual. This isn’t a problem; it’s simply an improvement. As of the date of publication,

all features, descriptions, and illustrations in this manual are correct.

New Solution Series User’s Manual

NSK 2480

Quiet Desktop Case

The Power Supply

NSK 2480 comes with an EarthWatts 380 Watt power supply. This universal

input, active PFC, single 80mm fan cooled power supply follows the ATX12V

version 2.2 specification, and includes dual +12V output rails that deliver safer

and more reliable output to your system’s components. EarthWatts power supplies

have achieved 80 PLUS® Certification, the latest independent standard in power

supply efficiency, and their higher energy efficiency reduces power consumption

by up to 25%, saving you money on your electricity bill. In addition EarthWatts

includes a variety of protective circuitry: OPP (over power protection), OVP (over

voltage protection), and SCP (short circuit protection).

The PSU comes with a main power switch. Make sure you turn the switch to the

ON (I) position before you boot up the computer for the first time. Normally, you

won’t need to switch to the OFF (O) position, since the PSU includes a soft on/off

feature. This lets you turn the computer on and off by using the soft switch on the

computer case. If the computer crashes and you can’t shut it down using the soft

switch, you can switch the main power to the OFF (O) position to shut the system

down. Then turn the switch back to the ON (I) position and reboot.

Although care has been taken to prevent sharp edges in your Antec case, we

strongly recommend taking your time and the appropriate care when working with

it. Hurried or careless motion and use of excessive force, particularly when you are

working in areas you cannot see clearly, are but a few examples of activity that

should be avoided. Please use reasonable precaution.

Setting Up

1. Place the case on a flat, stable surface.

2. Remove the thumbscrews from the back of the top panel. Slide the panel

towards the rear to remove it from the case.

3. Inside the case you should see the power supply, some wiring with marked

connectors (USB, PWR etc.), an installed I/O panel and a power cord.

The Triple Chamber structure

The case interior is divided into three separate chambers – the power supply

chamber, the motherboard chamber and the HDD chamber. This triple chamber

structure isolates heat and noise resulting in much quieter and cooler operation

Disclaimer

This manual is intended only as a guide for Antec’s Computer Enclosures. For more

comprehensive instructions on installing the motherboard and peripherals, please

refer to the user’s manuals that come with those components.

than in a traditional desktop case. There are small openings between the chambers to

allow for the routing of cables as needed.

Installing the Motherboard

This manual is not designed to cover CPU, RAM, or expansion card installation.

Please consult the motherboard manual for specific mounting instructions and

troubleshooting.

The motherboard is located inside the main chamber. Two 120mm TriCool™ fans

are preinstalled right next to the CPU.

1. Lay the case down so that the open side is up. You should be able to see the

drive bay and power supply.

2. Make sure you have the appropriate I/O panel for the motherboard. If the

panel provided is not suitable for your motherboard, please contact the

motherboard manufacturer for the correct I/O panel.

3. Line up the motherboard with the standoff holes. Determine which holes line

up and remember where they are. Not all motherboards will match with all of

the provided screw holes, and this is not necessary for proper functionality.

Some standoffs may be pre-installed for your convenience.

4. Lift up and remove the motherboard.

5. Screw in the brass standoffs to the threaded holes that line up with

the motherboard.

6. Place the motherboard on the brass standoffs.

7. Screw in the motherboard to the standoffs with the provided

Phillips-head screws.

8. The motherboard is now installed.

Connecting the Power and LED

The power supply conforms to the ATX12V Version 2.2 standard. Before you

connect the power supply to any of the devices, please consult the appropriate

user manuals for the motherboard and other peripherals.

1. Connect the 24-pin Main Power Connector and the

4-pin 12V connector to the motherboard as needed.

If the motherboard uses a 20-pin connector; detachthe

4-pin attachment on the 24-pin power connector

(see pictures 1 and 2). the detachable 4-pin Note:

section of the main power connector cannot be used

in place of a 4-pin +12V connector.

2. Connect the Reset switch (labeled RESET SW) to the motherboard at the RST

connector. Polarity (positive and negative) does not matter for switches.

3. Power Switch (labeled POWER SW) connects to the PWR connector on the

motherboard.

4. Power LED connector is a molex connector with blue/white wires. Connect

this to any molex connector on the power supply and this will illuminate the

circle around the power button when the system is on.

5. Hard Drive LED (labeled HDD LED) connects to the IDE connector. For LEDs,

colored wires are positive (+). White or black wires are negative (-). If the

LED does not light up when the system is powered on, try reversing the

connection. For more info on connecting LEDs to your motherboard, see your

motherboard manual.

Picture 1 Picture 2

For 24-pin

motherboards

For 20-pin

motherboards

Product specificaties

Merk:	Antec
Categorie:	Computerbehuizing
Model:	NSK2480-EC
Kleur van het product:	Zwart, zilver
Gewicht:	6530 g
Breedte:	445 mm
Diepte:	414 mm
Hoogte:	139.7 mm
Soort:	PC
Vormfactor:	Desktop
Aantal USB 2.0-poorten:	2
Certificering:	80 PLUS Certification \nActive PFC
Netvoeding:	380 W
Audio-ingangen:	Ja
Audio-uitgang:	Ja
Soort voeding:	80 Plus, PFC
Rack-montage:	Ja
Uitbreidingsslots:	4
Rackcapaciteit:	2U
Interne schijfposities:	4
Interne drive bays:	2 x 3.5"
Ventilator(en):	3
Main board size:	9.6 x 9.6 "