American International TOYK989 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor American International TOYK989 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Double DIN Mount Applications
NOTE: Remove shaded pocket support Tabs on left and right bracket.
1. Remove the shaded tab from the bottom of each left and right mounting bracket (See figure C below).
2. Cut and remove center rib from main frame and file edges smooth.
3. Attach the left and right side brackets to the main frame (See figure C below).
4. Follow steps 4-6 from single ISO instructions on page 3.
5. Attach a rear support bracket to the rear of the radio components and adjust as needed
to allow rear support in the sub-dash (optional).
CUSTOMER HELP LINE
8am-4:30 P.S.T. Monday-Friday Except Holidays
USA 800-323-4329 • Canada 800-245-8777
Toyota
2008-12 HIGHLANDER (WITHOUT FACTORY NAVIGATION)
VEHICLE APPLICATIONS
KIT ASSEMBLY INSTRUCTIONS
NOTE: #1 - ISO trim ring (DITR989) must be used in place of after-market radio’s trim rings. For ISO mount
applications, mount after-market radio components to side brackets using screws provided with
radio when possible or hardware included with kit.
For ISO mount only: Attach (1) ISO Spacer to the
inside of lower sections on both Left
& Right mounting brackets as shown in Fig. A.
Cut
Cut
Left
Right
Fig. A
DITR989
IMB989L
IMB989R
Fig. C
Main Frame
TOYK989 Mounting Kit
iTOYK989 ©2017 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 06/17 PRINT Ver. 06/17
Remove shaded pocket
support Tabs on left
and right bracket.
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B.
2. Insert pocket (part # POC989) into upper section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of lower section on both Left & Right mounting
brackets as shown in Fig. A.
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit (optional).
KIT ASSEMBLY INSTRUCTIONS
2 3
NOTE: #1 - ISO trim ring (ITR989) may be used in place of after-market radio’s removable trim ring.
ITR989
(BOTTOM
OPTIONAL)
For ISO mount only: Attach (1) ISO
Spacer to the inside of lower section
on both Left & Right mounting
brackets as shown in Fig. A.
Left
POC989
IMB989L
IMB989R
Right
Fig. A
Fig. B
Main Frame
NOTE: ISO trim ring (ITR989) may be used in
place of after-market radio’s removable trim ring.
(Some radio faces may be too large and the
trim ring may need to be modified)
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B opposite page.
2. Insert pocket (part # POC-989) into upper section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the lower section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. Attach a rear support bracket to the
rear of the new radio and adjust as
necessary to attach to the rear support
stud located on the back of the pocket
using the small phillips screw supplied
with kit (optional).
1. Carefully unclip and remove the vent panel above the radio. The vent panel is held to
the sub-dash with plastic clips.
2. Lower the glove box door.
3. Remove the climate control panel that extends from the glove box down to the access
door for the auxiliary plug and up to the key cylinder area. The access door is attached
to the trim bezel.
4. Remove the (4) 10mm bolts securing the radio in place.
5. There are (4) plastic clips left holding the radio in the sub dash.
6. Carefully pull forward the radio assembly to remove from the sub-dash.
7. Disconnect all harnesses and antenna leads attached to the radio assembly.
8. Remove the hazard switch assembly from the radio mounting brackets.
This will need to be reinstalled into the new installation kit.
9. Remove the clock assembly from the radio mounting brackets (4) phillips screws).
This will need to be installed in the new kit.
10.Remove the 4 radio support studs from the back of the factory radio.
DASH DISASSEMBLY AND RADIO REMOVAL INSTRUCTIONS
2008-2012 TOYOTA HIGHLANDER
(WITHOUT FACTORY NAVIGATION)
Main Frame
DIN Sleeve
KIT ASSEMBLY INSTRUCTIONS
1. Remove the 4 factory radio (upper + lower side) support studs,
as shown in Fig. D below, and attach to the rear side of the TOYK989
main bezel using the screws from the factory radio.
Fig. D
Support studs


Product specificaties

Merk: American International
Categorie: Niet gecategoriseerd
Model: TOYK989

Heb je hulp nodig?

Als je hulp nodig hebt met American International TOYK989 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd American International

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd