American DJ Freq 5 Handleiding

American DJ Verlichting Freq 5

Lees hieronder de 📖 handleiding in het Nederlandse voor American DJ Freq 5 (10 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

User Instructions

FREQ 5 Strobe Introduction

Rev. 1/13

Unpacking: Thank you for purchasing the FREQ 5 Strobe by Ameri-

can DJ . Every FREQ 5 Strobe has been thoroughly tested and has ®

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all accessories necessary to operate the unit has

arrived intact. In the case damage has been found or parts are miss-

ing, please contact our toll free customer support number for further

instructions. Do not return this unit to your dealer without rst contact-

ing customer support.

Introduction: The FREQ 5 Strobe is part of American DJ’s continuing

pursuit for creating high quality affordable intelligent fixtures. The FREQ

5 Strobe is a revolutionary 5-zone LED strobe. The unit has 4 operating

modes; Sound Active (with adjustable sound sensitivity), Show Mode,

Manual Mode, or DMX Control. This unit can be used as a stand alone

xture, or in a Master/Slave conguration. This fixture is suitable for

theaters, studios, retail stores, and other similar locations.

Customer Support: American DJ provides a toll free customer sup®-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@americandj.com

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ .®

PLEASE recycle the shipping carton when ever possible.

FREQ 5 Strobe Safety Precautions

• Built in Microphone

• 4 DMX Channel Modes: 1 Channel Mode, 2 Channel Mode, 5

Channel Mode, & 7 Channel Mode

• 12 Show Modes

• 4 Operating Modes - Sound Active, Show Mode, Manual Mode,

and DMX Control

• Sound Sensitivity Adjustable

• UC3 Remote Control Compatiable (Not Included)

• Power Cord Daisy Chaining. See page 17.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break off the ground

prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

t he manufacturer. See page 17 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (inclu-

d ing ampliers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

FREQ 5 Strobe Warranty Registration

FREQ 5 Strobe Features

To optimize the performance of this product, please read these operat-

ing instructions carefully to familiarize yourself with the basic operations

of this unit. These instructions contain important safety information

regarding the use and maintenance of this unit. Please keep this manual

with the unit, for future reference.

FREQ 5 Strobe General Instructions

The FREQ 5 Strobe carries a 3 year (1095 days) limited warranty.

Please ll out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www.

americandj.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact American DJ® cus-

tomer support for a R.A. number.

FREQ 5 Strobe Installation

The unit should be mounted using a mounting clamp (not provided),

afxing it to the mounting bracket that is provided with the unit.

Always ensure that the unit is rmly xed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10

times the unit’s weight. Also, always use a safety cable that can hold

12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be

installed in a place where it is out of the reach of people’s grasp.

©American DJ® - www.americandj.com - FREQ 5 Strobe Instruction Manual Page 5 © ®American DJ Supply - www.americandj.com - FREQ 5 Strobe Instruction Manual Page 6

Power Supply: The American DJ FREQ 5 Strobe contains a auto®-

matic voltage switch, which will auto sense the voltage when it is

plugged into the power source. With this switch there is no need to

worry about the correct power voltage, this unit can be plugged in

anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav-

els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX fixtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a single

controller, as long as all xtures and the controller are DMX compli-

ant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The FREQ 5 Strobe has 4 DMX Channel modes. The DMX address is set

on the rear panel of the FREQ 5 Strobe. Your unit and your DMX con-

troller require a approved DMX-512 110 Ohm Data cable for data input

and data output. We recommend Accu-Cable DMX cables. If you are

making your own cables, be sure to use standard

110-120 Ohm shielded cable (This cable may be

purchased at almost all professional sound and

lighting stores). Your cables should be made with

a male and female XLR connector on either end

of the cable. Also remember that DMX cable must

be daisy chained and cannot be split.

FREQ 5 Strobe Set Up

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket

XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

Termination educes signalr errors and

avoids signal transmission problem s

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture. Figure 4

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

FREQ 5 Strobe Set Up

Product specificaties

Merk:	American DJ
Categorie:	Verlichting
Model:	Freq 5

Heb je hulp nodig?

Als je hulp nodig hebt met American DJ Freq 5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Verlichting American DJ

American DJ ENCORE LB15IP Handleiding

18 December 2024

American DJ ENCORE LP12IP Handleiding

18 December 2024

American DJ RGBW4C IR Handleiding

15 November 2024

American DJ MyDMX5 Handleiding

8 April 2024

American DJ SDC24 Handleiding

18 Maart 2024

American DJ UV Flood 36 Handleiding

7 Mei 2023

American DJ Freq 5 Handleiding

6 Mei 2023

American DJ S-81 LED Handleiding

20 April 2023

American DJ Pocket Pro Handleiding

17 April 2023

American DJ myDMX 3.0 Handleiding

28 Maart 2023

Handleiding Verlichting

Nieuwste handleidingen voor Verlichting

LumenRadio CRMX Galileo MAX Handleiding

21 December 2024

Showtec Performer Fresnel 2200 DDT Handleiding

21 December 2024

Showtec AirDrive 2.4 IP Handleiding

21 December 2024

Bosch FSN 1400 Set Professional Handleiding

21 December 2024

Neewer VL66C Handleiding

18 December 2024

Wiesenfield UNI-LP-100 Handleiding

17 December 2024

Cateye Wearable mini SL-WA10 Handleiding

16 December 2024

Cateye Volt50 HL-EL460RC-REAR Handleiding

16 December 2024

Cateye Wearable X SL-WA100 Handleiding

16 December 2024

Luxli ORC-TIMPANI-M2 Handleiding

16 December 2024