Alto Stagedrive+ Handleiding

Alto Hifi systeem Stagedrive+

Lees hieronder de 📖 handleiding in het Nederlandse voor Alto Stagedrive+ (156 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/156
STAGEDRIVE+
QUICKSTART GUIDE
ENGLISH ( 1 - 26 )
GUÍA DE INICIO RÁPIDO
ESPAÑOL ( 27 - 52 )
GUIDE D’UTILISATION SIMPLIFIÉ
FRANÇAIS ( 53 – 77 )
GUIDA RAPIDA
ITALIANO ( 78 - 103 )
KURZANLEITUNG
DEUTSCH ( 104 – 128 )
SNELSTARTGIDS
NEDERLANDS ( 129 – 153 )
QUICKSTART GUIDE (ENGLISH)
BOX CONTENTS
STAGEDRIVE+
Power cable
Software CD
Quickstart Guide
Safety & Warranty Information Booklet
QUICK SETUP
1. Make sure all items listed in the BOX CONTENTS section are included in the box.
2. READ SAFETY & WARRANTY INFORMATION BOOKLET BEFORE USING THE PRODUCT.
3. Study the connection diagram in this guide.
4. Place all devices in an appropriate position for operation.
5. Make sure all devices are turned off and all faders and gain knobs are set to "zero."
6. Connect all sound sources' outputs to amplifier inputs as indicated in the diagram.
7. Connect the amplifier outputs to speakers.
8. Plug all devices into an appropriate power source.
9. Switch everything on in the following order:
• Sound sources (i.e. microphones, turntables, CD players, etc.)
• Mixer
• Amplifier
• Speakers
10. When turning powering down, turn everything off in the following order:
• Speakers
• Amplifier
• Mixer
• Sound sources
FRONT PANEL DIAGRAM
1. MODE BUTTON- Selecting one of four modes: PRESET, DELAY, EDIT and UTILITY.
2. DISPLAY- Shows the pages of the various menus and their parameters.
3. DIAL KNOB- Edits the value of the selected parameter.
4. PREV/NEXT BUTTON- Accesses menu pages and/or parameters.
5. NAVIGATION CURSOR KEYS- Selects various parameters.
6. MEMORY CARD SLOT- MMC card slot to store PRESETS.
7. ENTER KEY- Confirms editing of parameters.
8. ESC KEY- Exits the selected editing page or cancels an editing operation.
9. INPUT LEVEL LEDs- Shows the level of input A/B.
10. MUTE SWITCHES- Mutes the signal from any of the six respective outputs.
11. OUTPUT LEVEL LEDS- Shows the output level.
Note: The LIMITER will change the way in which the output level is displayed on the corresponding LED. The
level shown on the meter is no longer the "absolute" output level, but the level of the signal at -24dB, -12dB,
-6dB compared to the limiter threshold (indicated by the orange LIMIT LED).
1
23
4
6
5
7
8
9
10
11
2
REAR PANEL DIAGRAM
1
3
2456
7
8
1. AC INPUT AND FUSE HOLDER- Connect the included power cable here.
CAUTION: If the fuse needs to be replaced, please refer to a qualified technician. If the fuse continues
to blow after replacing, discontinue use of this unit and seek repair.
2. POWER SWITCH- Turns the main POWER on and off.
3. DIGITAL IN- Connect a balanced XLR-F cable here.
4. RS485 OUT- Allows outgoing communication between a STAGEDRIVE+ and other STAGEDRIVE+
units.
5. RS485 IN- Allows incoming communication between a STAGEDRIVE+ and other STAGEDRIVE+
units.
6. USB PORT- Allows communication via PC.
7. OUTPUTS- Use Balanced XLR-M cables on these outputs.
8. INPUTS- Balanced XLR - ¼” combo jacks.
GETTING STARTED
Adjusting the input signal
1. Keep the STAGEDRIVE+ outputs in MUTE status (LEDs on) by pressing each respective Mute button
on the front panel.
2. Feed a signal into the STAGEDRIVE+ input and watch the INPUT LEVEL A-B LED meter.
3. Keep the signal high, but without triggering the CLIP LED continually, adjusting the input gain if
necessary.
4. Press the MODE key until the EDIT menu LED lights up. Use the PREV and NEXT keys to go to the
Input Gain page and then press ENTER.
5. Use the DIAL to change the gain value and watch the level of the signal on the LED meter until ideal
values are reached.
6. Use the PREV and NEXT keys to access to the INB Gain page.
MENUS
PRESET Menu
Types of PRESETS
There are 3 categories of PRESETS:
• F = Factory PRESETS which cannot be permanently changed. These are the starting points for
creating User PRESETS and card PRESETS from scratch.
• U = User PRESETS can be programmed by users.
• C = Card PRESETS can be programmed by users and stored on a Multimedia Memory Card.

Product specificaties

Merk: Alto
Categorie: Hifi systeem
Model: Stagedrive+

Heb je hulp nodig?

Als je hulp nodig hebt met Alto Stagedrive+ stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Hifi systeem Alto

Alto

Alto MixPack Pro Handleiding

11 April 2023
Alto

Alto Black 15 Handleiding

11 Maart 2023
Alto

Alto Stealth Pro Handleiding

9 Maart 2023
Alto

Alto Stealth Wireless Handleiding

24 Februari 2023
Alto

Alto Live-Drive Handleiding

22 Januari 2023
Alto

Alto Stagedrive+ Handleiding

13 Januari 2023
Alto

Alto Transport 12 Handleiding

3 December 2022
Alto

Alto Black 18 sub Handleiding

14 Oktober 2022

Handleiding Hifi systeem

Nieuwste handleidingen voor Hifi systeem

Lenoxx

Lenoxx CD813 Handleiding

16 November 2024
Denon

Denon CEOL N-8 Handleiding

16 November 2024
Fiio

Fiio M7K Handleiding

16 November 2024
Fiio

Fiio X1II Handleiding

16 November 2024
Fiio

Fiio M3 Handleiding

16 November 2024
Fiio

Fiio X3 Mark III Handleiding

16 November 2024
Pro-Ject

Pro-Ject BT Box E HD Handleiding

15 November 2024
Blaupunkt

Blaupunkt RCD 204 Handleiding

15 November 2024
Samsung

Samsung MM-X7 Handleiding

15 November 2024
Auna

Auna VCP-191 Handleiding

14 November 2024